This patch for the ftdi_sio driver adds a bunch of new devices and fixes
an incorrect PID:
o Fix PID for ELV UO100 (the PID was in fact for ELV UR100).
o Add PID ELV UR100 (see above) and ELV ALC 8500 Expert.
o Add a whole bunch of other PIDs for ELV USB devices, commented out for
now as they may be used by other drivers eventually. (Christian Abt
of ELV.de submitted a full list of devices including an indication of
which set of drivers are used by default in the MS Windows world. We
decided to comment out the devices that use FTDI's D2XX Windows
drivers by default.)
o Add PIDs for eight devices from Xsens Technologies BV (submitted in a
patch against 2.6.12.2 by Patrick Riphagen).
o Add PID for Falcom Samba GPRS modem (submitted by Sebastian Schubert).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Support one user specified vendor and product ID via a couple
of new module parameters.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Fix timeouts in a couple of usb_control_msg() calls due to
change of units from jiffies to milliseconds in 2.6.12.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR. Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds the following new devices to the ftdi_sio driver:
* microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL).
* Evolution Robotics ER1 Control Module submitted by Shawn M. Lavelle.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Remove redundant handling of TIOCMBIS and TIOCMBIC ioctls
as they are handled in the tty layer and never reach this driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Use a single usb_device_id table and detect the type of chip
programatically. The table also flags devices requiring special
initialization. The patch makes the driver about 10K smaller and makes
it easier to add new device IDs.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Avoid losing bytes at tty-ldisc.
This patch was originally developed by Daniel Smertnig. I
(Ian Abbott) made a few changes. It has been tested by both
Daniel and I, at least for raw, non-canonical receive data
processing.
Here is Daniel's original description of the patch:
===
During a project in which I was using a FTDI 232BM to
transmit data at relative high speeds (625kBit/s), I
noticed a problem where data was lost even if flow
control was enabled: The FTDI-Driver receives 512 Bytes
of data over USB at a time, which consists of 8 64-Byte
packets. Subtracting the 2 bytes of status information
included in each packet this gives 496 "real" data
bytes per read.
This data is passed (indirectly, via the flip buffers)
to the tty line discipline which takes care of
throttling when there the free buffer space reaches
TTY_THRESHOLD_THROTTLE (128). Because the FTDI driver
processes up to 496 bytes at a time, throttling won't
happen in time and the line discipline will discard the
remaining bytes.
To avoid this the patch passes data in 62-byte blocks
to the tty layer and checks the available space in the
ldisc-buffers. If there isn't enough free space,
processing the rest of the data is delayed using a
workqueue.
Note: The original problem should be easily
reproducible with a userspace program which does slow &
small reads.
===
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Daniel Smertnig <daniel.smertnig@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Add PID for "ELV USB Module UM100".
PID sent by Armin Laugher.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ftdi_sio] Replaced redundant INTERFACE_A and INTERFACE_B macros with
the equivalent PIT_SIOA and PIT_SIOB macros.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some VID/PID updates for the ftdi_sio driver:
* The "Gude Analog- und Digitalsysteme GmbH" entries were missing from
the "combined" table.
* Replaced FTDI_8U232AM_ALT_ALT_PID with 3 PIDs for devices from
4n-galaxy.de.
* Removed redundant FTDI_RM_VID and renamed FTDI_RMCANVIEW_PID to
FTDI_RM_CANVIEW_PID.
* Added VID/PID for serial converter in Mobility Electronics EasiDock
USB 200 (mentioned by Gregory Schmitt).
* Added PID for Active Robots USB comms board (mentioned by John Koch).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -ur a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
Get rid of a bunch of redundant NULL pointer checks in drivers/usb/*,
there's no need to check a pointer for NULL before calling kfree() on it.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/class/audio.c
===================================================================
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Ian Abbott