This patch enables the wakeup capabilities of ads7846 touchscreen driver.
ads7846 driver can now wakeup the system from suspend on OMAP3430 EVM
and SDP boards.
The earlier approach of enabling wakeup on the touchscreen GPIO pin during
board level mux init is removed. Instead the wakeup flag in
ads7846_platform_data is enabled. Based on the flag, the ads7846 driver
will do an enable_irq_wake which will eventually call into the OMAP GPIO
layer and will enable the wakeup capability on the GPIO pin.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP3530 TRM section 7.4.4.4.2 requires OFFOUTENABLE to be set (active low)
if wakeup capabilities are enabled on a pad. During OFF mode testing
on OMAP3530 EVM, it was observed that the device was not residing in
the OFF state. The device enters into the OFF state and immediately exits
from that state as if an IO wakeup event has occured. The issue was traced
down to the pad configuration of wkaeup enabled pad's.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Millisecond resolution is possible and there are use cases for it
(automatic testing).
Seconds-based interface is preserved for compatibility.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Reviewed-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU. If these are not masked out, non-enabled
interrupts are caught, a WARN() is printed due to no 'handler' and the
events are cleared. In addition to being noisy, this can also
interfere with independent polling of this register by SR/VP code.
This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Acked-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This fixes a regression of
7d58289 (mx1: prefix SOC specific defines with MX1_ and deprecate old names)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. Remove CACHE_ALL_LOOP2 macro because it is identical to CACHE_ALL_LOOP
2. Change BUG_ON to WARN_ON
3. Remove end aligned from CACHE_LOOP_LIMITS.
C implementation do not need aligned end address and ASM code do aligned
in their macros
4. ASM optimized CACHE_RANGE_LOOP_1/2 macros needs to get aligned end address.
Because end address is compound from start + size, end address is the first address
which is exclude.
Here is the corresponding code which describe it.
+ int align = ~(line_length - 1);
+ end = ((end & align) == end) ? end - line_length : end & align;
a) end is aligned:
it is necessary to subtruct line length because we don't want to work with
next cacheline
b) end address is not aligned:
Just align it to be ready for ASM code.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Microblaze cacheline length is configurable and current cpu
uses two cacheline length 4 and 8.
We are taking conservative maximum value to be sure that cacheline
alignment is satisfied for all cases.
Here is the calculation for cacheline lenght 8 32bit=4Byte values
which is corresponding with SHIFT 5.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Based on PowerPC patche 52142e756e
PowerPC description:
On platforms doing non-coherent DMA (4xx, 8xx, ...), it's important
that the kmalloc minimum alignment is set to the cache line size, to
avoid sharing cache lines between different objects, so that DMA to
one of the objects doesn't corrupt the other.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch fix consistent code which had problems with consistent_free
function.
I am not sure if we need to call flush_tlb_all after it but it keeps
tlbs synced.
I added noMMU and MMU version together.
Uncached shadow feature is not tested.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Current implementation doesn't handle dcache_line_length
correctly that's why is better to use generic memcpy.
Cache optimized function could be good way howto improve
performance but must be based on benchmarking not blind
function like this.
Signed-off-by: Michal Simek <monstr@monstr.eu>
As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Michal Simek <monstr@monstr.eu>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Fix divide exception message to say "divide by zero".
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Signed-off-by: Michal Simek <monstr@monstr.eu>
Remove section mismatch - based on ppc aproach.
WARNING: vmlinux.o(.text+0x64834): Section mismatch in reference
from the function __pte_alloc_kernel() to the function .init.text:early_get_page()
The function __pte_alloc_kernel() references
the function __init early_get_page().
This is often because __pte_alloc_kernel lacks a __init
annotation or the annotation of early_get_page is wrong.
Signed-off-by: Michal Simek <monstr@monstr.eu>
_start is located in .text, which causes mismatch warnings with
machine_early_init() and start_kernel() in .init.text.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Function traces on Microblaze don't include IRQ entry and exit arrows,
i.e.
0) | memcpy_toiovec() {
0) ==========> |
0) | do_IRQ() {
...
0) <========== |
0) ! 5414.000 us | }
...because do_IRQ() doesn't have the proper attributes.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This change should be part of b26b2d494b
Origin description:
resource/PCI: align functions now return start of resource
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This change should be part of 89a74ecccd
Origin description:
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Michal Simek <monstr@monstr.eu>
The use of mfp_cfg_t causes build errors without including <mach/mfp.h>.
CC: stable@kernel.org
CC: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Jakob Viketoft <jakob.viketoft@bitsim.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On/Off contains slash in the name, which causes warning during boot.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Fix the wrong variable used in cpu_is_pxa950().
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Update CPUID pattern of PXA9xx in head.S and fix the duplicate
entries for pxa935.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The timeout value is in jiffies, so it should be using HZ, not a plain
number. Assume with HZ=100 '100' means 1s here and adapt accordingly.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Shen <paul.shen@marvell.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
"on/off button" was recently renamed to remove the slash character.
Follow that change in the pin polarity detection as well.
While at it, fix another cosmetic coding style flaw as well.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
- Bring in a CMDLINE that actually works and prints to the right tty
- Compile-in JFFS2 to boot into rootfs
- Remove unneeded options for Bluetooth and radio
- Disable CPU_FREQ as it makes the flash driver fail
Thanks Jonathan for spotting what I messed up.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The x86_64 call_rwsem_wait() treats the active state counter part of the
R/W semaphore state as being 16-bit when it's actually 32-bit (it's half
of the 64-bit state). It should do "decl %edx" not "decw %dx".
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The show_mem() and mem_init() function are assuming that the page map is
contiguous and calculates the start and end page of a bank using (map +
pfn). This fails with SPARSEMEM where pfn_to_page() must be used.
Tested-by: Will Deacon <Will.Deacon@arm.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With F10, model 10, all valid frequencies are in the ACPI _PST table.
Cc: <stable@kernel.org> # 33.x 32.x
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
LKML-Reference: <1270065406-1814-6-git-send-email-bp@amd64.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit e67a807 ("x86: Fix 'reservetop=' functionality") added a
fixup_early_ioremap() call to parse_reservetop() and declared it
in io.h.
But asm/io.h was only included indirectly - and on some configs
not at all, causing a build failure on those configs.
Cc: Liang Li <liang.li@windriver.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1272621711-8683-1-git-send-email-liang.li@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
iop32x_defconfig:
In file included from include/linux/elf.h:7,
from kernel/elfcore.c:1:
arch/arm/include/asm/elf.h:101: warning: "struct task_struct" declared inside parameter list
arch/arm/include/asm/elf.h:101: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Just to make sure that this driver won't run on StrongArm SA1100
when both SA1100 and SA1110 cpufreq drivers are built in (usually
in multimachine config). SA1100 driver already has similar check.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
They have StrongARM SA1110, not SA1100.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the preempt leak in the cpuidle path invoked from
cpu-hotplug. The fix is suggested by Russell King and is based
on x86 idea of calling init_idle() on the idle task when it's
re-used which also resets the preempt count amongst other things
dump:
BUG: scheduling while atomic: swapper/0/0x00000002
Modules linked in:
Backtrace:
[<c0024f90>] (dump_backtrace+0x0/0x110) from [<c0173bc4>] (dump_stack+0x18/0x1c)
r7:c02149e4 r6:c033df00 r5:c7836000 r4:00000000
[<c0173bac>] (dump_stack+0x0/0x1c) from [<c003b4f0>] (__schedule_bug+0x60/0x70)
[<c003b490>] (__schedule_bug+0x0/0x70) from [<c0174214>] (schedule+0x98/0x7b8)
r5:c7836000 r4:c7836000
[<c017417c>] (schedule+0x0/0x7b8) from [<c00228c4>] (cpu_idle+0xb4/0xd4)
# [<c0022810>] (cpu_idle+0x0/0xd4) from [<c0171dd8>] (secondary_start_kernel+0xe0/0xf0)
r5:c7836000 r4:c0205f40
[<c0171cf8>] (secondary_start_kernel+0x0/0xf0) from [<c002d57c>] (prm_rmw_mod_reg_bits+0x88/0xa4)
r7:c02149e4 r6:00000001 r5:00000001 r4:c7836000
Backtrace aborted due to bad frame pointer <c7837fbc>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With CONFIG_KPROBES enabled two section are getting created which
leads to below build break.
LOG:
AS arch/arm/kernel/entry-armv.o
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:431: Error: symbol ret_from_exception is in a different section
arch/arm/kernel/entry-armv.S:490: Error: symbol ret_from_exception is in a different section
arch/arm/kernel/entry-armv.S:491: Error: symbol __und_usr_unknown is in a different section
This was introduced by commit 4260415f6a
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Upstream PV guests fail to boot because of a NULL pointer in
irq_force_complete_move(). It is possible that xen guests have
irq_desc->chip_data = NULL.
Test for NULL chip_data pointer before attempting to complete an irq move.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
LKML-Reference: <20100427152434.16193.49104.sendpatchset@prarit.bos.redhat.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org> [2.6.33]
The -mfix-loongson2f-jump option provided by latest CVS binutils have fixed
the out-of-order issue of Loongson-2F described in chapter 15 of the
Loongson2F User Manual [1, 2], but introduced some problems.
The option changes all of the jump target to "addr & 0xcfffffff" through the
at($1) register, but for the reboot address of Loongson 2F 0xbfc00000 this is
wrong. Avoids the problem via telling the assembler to not use the $at
register.
[1] Loongson2F User Manual (Chinese Version)
http://www.loongson.cn/uploadfile/file/200808211
[2] English Version of Chapter 15:
http://groups.google.com.hk/group/loongson-dev/msg/e0d2e220958f10a6?dmode=source
Reported-and-tested-by: Liu Shiwei <liushiwei@gmail.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the "Fixups of Loongson2F" patch [1] having been applied to binutils
for binutils 2.20.1 we now can use it's time to enable the options provided
by the patch to compile the kernel.
Without these fixups, the system may hang if the erratum is triggered.
For more information on these fixups please refer to the following
references.
[1] "Fixups of Loongson2F" patch for binutils(actually for gas)
http://sourceware.org/ml/binutils/2009-11/msg00387.html
[2] Chapter 15 of "Loongson2F User Manual"(Chinese Version)
http://www.loongson.cn/uploadfile/file/200808211
[3] Chapter 15 of the English version Loongson 2F User Manual
http://groups.google.com.hk/group/loongson-dev/msg/e0d2e220958f10a6?dmode=source
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Zhang Le <r0bertz@gentoo.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As documented in the Loongson 2F User Manual [2, 3], the old Loongson2F
series (2F01 / 2F02) have the NOP & JUMP issues which requires workarounds
in the kernel and binutils. This issue has been rectified in Loongson 2F
series 2F03 so no workarounds needed.
Now that the workarounds [1] adding the the -mfix-loongson2f-nop and
-mfix-loongson2f-jump options have been comitted to the binutils the CVS
repository), we can add the workarounds in the kernel.
The workarounds have no significant side effect on the system but may
decrease performance so we control them through a a new
CPU_LOONGSON2F_WORKAROUNDS config option allowing the users to only enable
it as necessary.
[1] "Fixups of Loongson2F" patch for binutils(actually for gas)
http://sourceware.org/ml/binutils/2009-11/msg00387.html
[2] Chapter 15 of "Loongson2F User Manual"(Chinese Version)
http://www.loongson.cn/uploadfile/file/200808211
[3] English Version of the above chapter 15
http://groups.google.com.hk/group/loongson-dev/msg/e0d2e220958f10a6?dmode=source
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1105/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ranjith Lohithakshan