Commit 5a5f561 (convert OMAP3 PRCM macros to the _SHIFT/_MASK suffixes)
mistakenly removed the check for PER when disabling the IO chain.
During idle, if the PER powerdomain transitions into a lower state
and CORE does not, the IO pad wakeups are not being disabled in
the idle path after they are enabled. This can happen with the
lower C-states when using CPUidle for example.
This patch ensures that the check for disabling IO wakeups also checks
for PER transitions, matching the check done to enable IO wakeups.
Found when debugging PM/CPUidle related problems reported by Ameya
Palande <ameya.palande@nokia.com>. Problems were triggered
particularily on boards with UART2 consoles (n900, Overo) since UART2
is in the PER powerdomain.
Tested on l-o master (omap3_defonfig + CONFIG_CPU_IDLE=y) as well
as with current PM branch. Boards tested: n900, Overo, omap3evm.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@nokia.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description to clarify the transistion]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3505/3517 doesn't have IO wakeup capability, so we do not need to set
the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register
PM_WKEN_WKUP when the system enters suspend state.
Tested on AM3517EVM and OMAP3530EVM.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Checking to se if the IO daisy chain is enabled should be checking the
PM_WKEN register, not the PM_WKST register. Reading PM_WKST tells us
if an event occurred, not whether or not it is enabled.
Apparently, we've been lucky until now in that a pending event has not
been there during enable. However, on 3630/Zoom3, I noticed because
of the WARN that this timeout was always happening.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error. This patch should
not cause any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.' This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.
The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We can remove this wakeup dependency since now, when
GPIO2-6 are enabled for IO-pad wakeup, PER domain is gauranteed
to be awake or be woken up to service.
The previous dependency did not handle all corner cases. Since there
was no sleep dependency between CORE and PER domains, if PER enters
RET and CORE is ON, PER will not be active for GPIO handling.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IO events can also come from GPIO modules, which reside in the PER domain.
It is possible for the PER to enter RET while CORE is still in ON.
If GPIO 2-6 are enabled for IO-pad wakeups, the PER domain will not
wakeup in this case, unless we enable it.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Millisecond resolution is possible and there are use cases for it
(automatic testing).
Seconds-based interface is preserved for compatibility.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Reviewed-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU. If these are not masked out, non-enabled
interrupts are caught, a WARN() is printed due to no 'handler' and the
events are cleared. In addition to being noisy, this can also
interfere with independent polling of this register by SR/VP code.
This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Acked-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add _MASK suffix to CM_FCLKEN_IVA2 bitfieds to conform with the rest
of the usage in cm-regbits-34xx.h of using _SHIFT and _MASK suffixes.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When 'enable_off_mode' is 0, the target power state for MPU
and CORE was locally changed to PWRDM_POWER_RET but, the
statistics are updated for idle state originally selected
by the governor.
This patch 'invalidates' the idle states that lead either of
MPU or Core to PWRDM_POWER_OFF state when 'enable_off_mode'
is '0'. The states are valid once 'enable_off_mode' is set
to '1'.
Added function next_valid_state() to check if current state
is valid; else get the next valid state. It is called from
omap3_enter_idle_bm().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add usecounting for wakeup and sleep dependencies. In the current
situation, if several functions add dependencies on the same
clockdomains, when the first dependency removal function is called,
the dependency will be incorrectly removed from the hardware.
Add clkdm_clear_all_wkdeps() and clkdm_clear_all_sleepdeps(), which
provide a fast and usecounting-consistent way to clear all hardware
clockdomain dependencies, since accesses to these registers can be
quite slow. pm{2,3}4xx.c has been updated to use these new functions.
The original version of this patch did not touch these files, which
previously wrote directly to the wkdep registers, and thus confused
the usecounting code. This problem was found by Kevin Hilman
<khilman@deeprootsystems.com>.
N.B.: This patch introduces one significant functional difference over
the previous pm34xx.c code: sleepdeps are now cleared during
clockdomain initialization, whereas previously they were left
untouched. This has been tested by Kevin and confirmed to work.
The original version of this patch also did not take into
consideration that some clockdomains do not have sleep or wakeup
dependency sources, which caused NULL pointer dereferences. This
problem was debugged and fixed by Kevin Hilman
<khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Move clockdomain wakeup dependency and sleep dependency data
structures from the powerdomain layer to the clockdomain layer, where
they belong. These dependencies were originally placed in the
powerdomain layer due to unclear documentation; however, it is clear
now that these dependencies are between clockdomains. For OMAP2/3,
this is not such a big problem, but for OMAP4 this needs to be fixed.
Thanks to Benoît Cousson <b-cousson@ti.com> for his advice on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Module offsets were same for OMAP2 and OMAP3 while they differ for OMAP4.
Hence we need different macros for identifying platform specific offsets.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Currently, DSS does not wakeup when there is a DMA request. DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.
Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
`!' has a higher precedence than `&' so parentheses are required.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a bug where scheduling is delayed until next wakeup due to race
condition (e.g. interrupt requests scheduling just before omap_sram_idle
is entered.)
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes the check to see if some functional clocks are
still enabled before entering sleep. This is no longer needed when
using safe state (C1) that keeps CORE active.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It is more efficient to use pwrdm_set_next_pwrst for mpu, core and neon
instead of set_pwrdm_state in idle loop. It is anyway known that those are
active in idle loop. So no need to use set_pwrdm_state.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Previously omap3_idle_init() was called in device_init, while
omap_pm_init() is called at late_initcall. This causes the cpu idle
driver to call omap_sram_idle before it is properly initialized. This
patch fixes the issue by moving omap3_idle_init into omap3_pm_init.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support and enables state C4(MPU RET + CORE RET)
and MPU OFF states (C3 and C5.)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Basic CPUidle driver for OMAP3 with deepest sleep state supported
being MPU CSWR.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to an OMAP3 errata (1.142), on HS/EMU devices SDRC should be
programed to issue automatic self refresh on timeout
of AUTO_CNT = 1 prior to any transition to OFF mode.
This is needed only on sil rev's ES3.0 and above.
This patch enables the above needed WA in the SDRC power register
value stored in scratchpad, so that ROM code restores this value
in SDRC POWER on the wakeup path.
The original SDRC POWER register value is stored and restored back
in omap_sram_idle() function.
This fixes some random crashes observed while stressing suspend
on HS/EMU devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP 3430 ES3.1 chips have a separate bit for IO daisy-chain
wake up enabling. It needs to be enabled when entering
retention or off state, otherwise waking up might not work
in all situations.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
MPU and CORE should stay awake if there is CAM domain ACTIVE. This is
because that module doesn't have wake-up capability.
This should replace the patch that is currently in the PM branch.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP3 can't generate wakeups in this state, thus it is not permitted.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using debugfs, export a configurable wakeup timer to be used to
wakeup system from suspend.
If a non-zero value is written to
/debug/pm_debug/wakeup_timer_seconds, A timer wakeup event will wake
the system and resume after the configured number of seconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Allow enable/disable of low-power states during idle. To
enable low-power idle:
echo 1 > /debug/pm_debug/sleep_while_idle
to disable:
echo 0 > /debug/pm_debug/sleep_while_idle
Also allow enable/disable of OFF-mode. To enable:
echo 1 > /debug/pm_debug/enable_off_mode
to disable:
echo 0 > /debug/pm_debug/enable_off_mode
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The SMS_SYSCONFIG register gets reset in off mode, added a
save/restore mechanism for that.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The secure sram context save uses dma channels 0 and 1.
In order to avoid collision between kernel DMA transfers and
ROM code dma transfers, we need to reserve DMA channels 0
1 on high security devices.
A bug in ROM code leaves dma irq status bits uncleared.
Hence those irq status bits need to be cleared when restoring
DMA context after off mode.
There was also a faulty parameter given to PPA in the secure
ram context save assembly code, which caused interrupts to
be enabled during secure ram context save. This caused the
save to fail sometimes, which resulted the saved context
to be corrupted, but also left DMA channels in secure mode.
The secure mode DMA channels caused "DMA secure error with
device 0" errors to be displayed.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix for ES3.0 bug: SDRC not sending auto-refresh when OMAP wakes-up
from OFF mode (warning for HS devices.)
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The function omap3_save_secure_ram() is now called only once during
the initialization of the device and consequent sleep cycles will
re-use the same saved contents for secure RAM. Users who need secure
services should do secure RAM saving before entering off-mode, if a
secure service has been accessed after last save.
There are both latency and reliability issues with saving secure RAM
context in the idle path. The context save uses a hardware resource
which takes an order of hundreds of milliseconds to initialize after a
wake up from off-mode, and also there is no way of checking whether it
is ready from kernel side or not. It just crashes if you use it too
quickly
Additional fix to ensure scratchpad save is done after secure
RAM by Roger Quadros.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, some additional resources need to be
saved/restored for off-mode support. Namely, saving the secure RAM
and a pointer to it in the scratchpad.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, these additional features are also used:
- DMA interrupt disable routine added
- Added DMA controller reset to DMA context restore
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for CORE powerdomain resources in order
to support off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a 'save_state' option when calling into SRAM idle function
and adds some minor cleanups of SRAM asm code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
During the MMU restoration on the restore path from MPU OFF, the page
table entry for the page consisting of the code being executed is
modified to make MMU return VA=PA.
The MMU is then enabled and the original entry is being stored in
scratchpad. This patch reads the original values stored in
scratchpad, and restores them back.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Expand the powerdomains handled in the idle path to include PER, NEON
and CORE. This includes properly clearing the previous powerstates,
linking NEON state to MPU state and calling the UART prepare functions
for only the appropraite powerdomain transitions (CORE for UART1,2,
PER for UART3.)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Generalize the copy of SRAM functions into omap_push_sram_idle()
so it can be used on init but also after off-mode transitions.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman