The local APIC is no longer forced off when "nosmp" has been specified.
Correct the message printed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Disable the 8259A acting in the "virtual wire" mode to keep the interrupt
line inactive while fiddling with local APIC interrupt vector registers
associated with its destination inputs. To be on the safe side,
especially concerning flipping the trigger mode.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Disable the 8259A when routing of the timer interrupt through the chip to
the local APIC of the primary processor has failed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the "disable_8254_timer" and "enable_8254_timer" kernel
parameters. Now that AEOI acknowledgements are no longer needed for
correct timer operation, the 8259A can be kept disabled unconditionally
unless interrupts, either timer or watchdog ones, are actually passed
through it.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The code that used to be in do_slow_gettimeoffset() that relied on the
IRR bit of the master 8259A PIC for IRQ0 to check the state of the output
timer 0 of the PIT is no longer there. As a result, there is no need to
use the POLL command to acknowledge the timer interrupt in the "8259A
Virtual Wire", except for the NMI watchdog when the i82489DX APIC is used
(this is because this particular APIC treats NMIs as level-triggered and
keeping the input asserted would keep motherboard NMI sources held off for
too long). Remove the unneeded bits and adjust comments accordingly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use PAGE_OFFSET macro instead of using 0xffff810000000000UL directly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: hpa@zytor.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
1) Remove __meminit from update_pages_count. It is used inside
split_pages()
2) Make the code depend on PROC_FS. Doing statistics for nothing is
useless and not adding useless code is nice to the Linux tiny folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add information about the mapping state of the direct mapping to
/proc/meminfo. I chose /proc/meminfo because that is where all the other
memory statistics are too and it is a generally useful metric even
outside debugging situations. A lot of split kernel pages means the
kernel will run slower.
This way we can see how many large pages are really used for it and how
many are split.
Useful for general insight into the kernel.
v2: Add hotplug locking to 64bit to plug a very obscure theoretical race.
32bit doesn't need it because it doesn't support hotadd for lowmem.
Fix some typos
v3: Rename dpages_cnt
Add CONFIG ifdef for count update as requested by tglx
Expand description
v4: Fix stupid bugs added in v3
Move update_page_count to pageattr.c
Signed-off-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
v2: fix early_panic on this config:
http://redhat.com/~mingo/misc/config-Thu_Jun_19_14_22_37_CEST_2008.bad
reason : struct cpu_vendor_dev size is 16, need to make table to be 16
byte alignment
also print out the cpu supported...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"Form follows function". Code is now where it belongs to.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The name fits better since this is code not only for K8.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Tue, 17 Jun 2008, Rafael J. Wysocki wrote:
>
> BTW, with the C1E patches reverted I don't get the
> WARNING: at /home/rafael/src/linux-next/kernel/smp.c:215 smp_call_function_single+0x3d/0xa2
> in the log. Thomas?
The BROADCAST_FORCE notification uses smp_function_call and therefor
must be run with interrupts enabled.
While at it, add a comment for the BROADCAST_EXIT notifier as well.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
C1E on AMD machines is like C3 but without control from the OS. Up to
now we disabled the local apic timer for those machines as it stops
when the CPU goes into C1E. This excludes those machines from high
resolution timers / dynamic ticks, which hurts especially X2 based
laptops.
The current boot time C1E detection has another, more serious flaw
as well: some BIOSes do not enable C1E until the ACPI processor module
is loaded. This causes systems to stop working after that point.
To work nicely with C1E enabled machines we use a separate idle
function, which checks on idle entry whether C1E was enabled in the
Interrupt Pending Message MSR. This allows us to do timer broadcasting
for C1E and covers the late enablement of C1E as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The pxa27x DMA controller defaults to 64-bit alignment. This caused
the SCR reads to fail (and, depending on card type, error out) when
card->raw_scr was not aligned on a 8-byte boundary.
For performance reasons all scatter-gather addresses passed to
pxamci_request should be aligned on 8-byte boundaries, but if
this can't be guaranteed, byte aligned DMA transfers in the
have to be enabled in the controller to get correct behaviour.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit e872154921.
Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver. Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example
http://lkml.org/lkml/2008/7/5/236
for an analysis.
The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "remote_irr" variable is used to indicate an interrupt
which has been received by the LAPIC, but not acked.
In our EOI handler, we unset remote_irr and re-inject the
interrupt if the interrupt line is still asserted.
However, we do not set remote_irr here, leading to a
situation where if kvm_ioapic_set_irq() is called, then we go
ahead and call ioapic_service(). This means that IRR is
re-asserted even though the interrupt is currently in service
(i.e. LAPIC IRR is cleared and ISR/TMR set)
The issue with this is that when the currently executing
interrupt handler finishes and writes LAPIC EOI, then TMR is
unset and EOI sent to the IOAPIC. Since IRR is now asserted,
but TMR is not, then when the second interrupt is handled,
no EOI is sent and if there is any pending interrupt, it is
not re-injected.
This fixes a hang only seen while running mke2fs -j on an
8Gb virtio disk backed by a fully sparse raw file, with
aliguori "avoid fragmented virtio-blk transfers by copying"
changes.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Hypercalls can modify arbitrary regions of memory. Make sure to indicate this
in the clobber list. This fixes a hang when using KVM_GUEST kernel built with
GCC 4.3.0.
This was originally spotted and analyzed by Marcelo.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Fix some issues in pagemap_read noted by Alexey:
- initialize pagemap_walk.mm to "mm" , so the code starts working as
advertised
- initialize ->private to "&pm" so it wouldn't immediately oops in
pagemap_pte_hole()
- unstatic struct pagemap_walk, so two threads won't fsckup each other
(including those started by root, including flipping ->mm when you don't
have permissions)
- pagemap_read() contains two calls to ptrace_may_attach(), second one
looks unneeded.
- avoid possible kmalloc(0) and integer wraparound.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Personally, I'd just remove the functionality entirely - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These two macros are useful beyond lock debugging. Moved definitions from
include/linux/debug_locks.h to include/linux/kernel.h, so code that needs
them does not have to include the former, which would have been a less
intuitive choice of a header.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 ACPI: fix resume from suspend to RAM on uniprocessor x86-64
x86 ACPI: normalize segment descriptor register on resume
Don't use a static entry, so as to prevent races during concurrent use
of this function.
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ea0c62f7cf tried to clear all
bits in irq_stat but it didn't actually achieve that as irq_stat was
anded with port_map right after read. This patch makes ahci driver
always use the unmasked value to clear irq_status.
While at it, add explanation on the peculiarities of ahci IRQ
clearing.
This was spotted by Linus Torvalds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Holding ide_lock for ide_release_dma_engine() call is unnecessary
and triggers WARN_ON(irqs_disabled()) in dma_free_coherent().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
class->dev_release is called by device_release() iff dev->release
is not present so ide_port_class_release() is never called and the
last hwif->gendev reference is not dropped.
Fix it by removing ide_port_class_release() and get_device() call
from ide_register_port() (device_create_drvdata() takes a hwif->gendev
reference anyway).
This patch fixes hang on wait_for_completion(&hwif->gendev_rel_comp)
in ide_unregister() reported by Pavel Machek.
Cc: Pavel Machek <pavel@suse.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Most places in the kernel that go BUG: print a module list
(which is very useful for doing statistics and finding patterns),
however the softlockup detector does not do this yet.
This patch adds the one line change to fix this gap.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the trampoline code is now used for ACPI resume from suspend to RAM,
the trampoline page tables have to be fixed up during boot not only on SMP
systems, but also on UP systems that use the trampoline.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=10923
Reported-by: Dionisus Torimens <djtm@gmx.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some Dell laptops enter resume with apparent garbage in the segment
descriptor registers (almost certainly the result of a botched
transition from protected to real mode.) The only way to clean that
up is to enter protected mode ourselves and clean out the descriptor
registers.
This fixes resume on Dell XPS M1210 and Dell D620.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=10927
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Flags considered internal to the mempolicy kernel code are stored as part
of the "flags" member of struct mempolicy.
Before exposing a policy type to userspace via get_mempolicy(), these
internal flags must be masked. Flags exposed to userspace, however,
should still be returned to the user.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even the newer ENE controllers have bugs in their DMA engine that make
it too dangerous to use. Disable it until someone has figured out under
which conditions it corrupts data.
This has caused problems at least once, and can be found as bug report
10925 in the kernel bugzilla.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Document the kernel boot parameter: relax_domain_level=.
Signed-off-by: Paul Jackson <pj@sgi.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
# cat /devcg/devices.list
a *:* rwm
# echo a > devices.allow
# cat /devcg/devices.list
a *:* rwm
a 0:0 rwm
This is odd and maybe confusing. With this patch, writing 'a' to
devices.allow will add 'a *:* rwm' to the whitelist.
Also a few fixes and updates to the document.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a bug in the output of /sys/devices/system/node/node[n]/meminfo
where the Active and Inactive values are in pages instead of Kbytes.
Looks like this occurred back in 2.6.20 when the code was changed
over to use node_page_state().
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In linux-next there is a commit ("x86: Add performance variants of cpumask
operators") which, as part of the 4096 cpu support work adds some new APIs
for dealing with cpu masks. Add trivial versions of these now so that
subsystems can update in a timely manner and avoid conflicts in linux-next
and the next merge window.
Cc: Mike Travis <travis@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CaFe chip has a hardware bug that ends up with us getting a timeout
value that's too small, causing the following sorts of problems:
[ 60.525138] mmcblk0: error -110 transferring data
[ 60.531477] end_request: I/O error, dev mmcblk0, sector 1484353
[ 60.533371] Buffer I/O error on device mmcblk0p2, logical block 181632
[ 60.533371] lost page write due to I/O error on mmcblk0p2
Presumably this is an off-by-one error in the hardware. Incrementing
the timeout count value that we stuff into the TIMEOUT_CONTROL register
gets us a value that works. This bug was originally discovered by
Pierre Ossman, I believe.
[thanks to Robert Millan for proving that this was still a problem]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has been sitting around unloved for way too long..
The Marvell CaFe chip's SD implementation chokes during card insertion
if one attempts to set the voltage and power up in the same
SDHCI_POWER_CONTROL register write. This adds a quirk that does
that particular dance in two steps.
It also adds an entry to pci_ids.h for the CaFe chip's SD device.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the way we determine the maximum number of outstanding
commands for each controller.
Most Smart Array controllers can support up to 1024 commands, the notable
exceptions are the E200 and E200i.
The next generation of controllers which were just added support a mode of
operation called Zero Memory Raid (ZMR). In this mode they only support
64 outstanding commands. In Full Function Raid (FFR) mode they support
1024.
We have been setting the queue depth by arbitrarily assigning some value
for each controller. We needed a better way to set the queue depth to
avoid lots of annoying "fifo full" messages. So we made the driver a
little smarter. We now read the config table and subtract 4 from the
returned value. The -4 is to allow some room for ioctl calls which are
not tracked the same way as io commands are tracked.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old one bounces.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andreas Dilger <adilger@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maciej W. Rozycki