This patch decouples the dependency between the rx checksum feature and
vlan feature. This is done by ignoring the checksum information if the
user has disabled rx checksum when vlan is enabled.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses an errata found on certain marvell phys concerning
the reset of the BMCR phy register during phy reset.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adds PCI Error recovery callbacks to the Intel 10-gigabit ethernet ixgb
device driver. Lightly tested, works.
"Zhang, Yanmin" <yanmin_zhang@linux.intel.com> wrote:
Both pci_disable_device and ixgb_down would access the device. It doesn't
follow Documentation/pci-error-recovery.txt that error_detected shouldn't do
any access to the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
A recent patch in -mm3 titled
"gregkh-pci-pci-don-t-enable-device-if-already-enabled.patch" causes
pci_enable_device() to be a no-op if the kernel thinks that the device is
already enabled. This change breaks the PCI error recovery mechanism in
the e100 device driver, since, after PCI slot reset, the card is no longer
enabled. This is a trivial fix for this problem. Tested.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Device 0x10a4 is a double 82571 on a single PCI-Express card and
has 4 gigabit capable ports.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
WoL is constantly giving problems and needed a rewrite. Consolidates
all WoL capabilities into a single function, and disables WoL for all
other ports on the device except for port A.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
struct cp_private is reorganized to be more easily compared between the
r8169 and the 8139cp drivers.
The alignment should not be impacted.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The ring_info.len field is not used at all. cp_private.rx_skb is
turned into an array of sk_buff *.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
No need to chew CPU cycles as there is no heavy timing requirement
and the delays are always requested from a sleepable context.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The current probe table causes ledma and lebuffer
"le" devices to get probed twice which is not what
we want.
Match just "le" and look directly at the parent to get the correct
top-level node information.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found by inspection. The STRIP driver does neigh_lookup() but never
releases. This driver shouldn't being doing gratuitous arp anyway.
Untested, obviously, because of lack of hardware.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several people run into the situation where the E100
EEPROM contents are fine, but the checksum hasn't been
set properly. This renders the device useless for
them even though it would function correctly.
The default is off, which retains the current behavior.
Signed-off-by: David S. Miller <davem@davemloft.net>
The user level irq balance daemon uses "eth" as a way to distinquish
ethernet devices. Also, by using device name it is possible to distinquish
different boards.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To avoid problems with buggy protocols that assume extra header space,
use dev_alloc_skb() when allocating receive buffers.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At the end of a critical section, we need to force the PCI write
to complete by doing a read.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code for suspend/resume needs several fixes. The hardware lock
should be setup in probe only, not in resume. Interrupts should be
disabled during suspend, etc.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To save power, don't enable power to the PHY until device is brought up.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since many packets have the same checksum starting offset and insertion
location; the driver can save the last information and only tell hardware
when it changes.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The MSS in the transmit engine only has to change if TSO mtu changes. This
means less commands to the chip when mixing TSO and regular data.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The test for MSI IRQ could have timing issues. The PCI write needs to be
pushed out before waiting, and the wait queue should be initialized before
the IRQ.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't use force status bit. It was never implemented on all chips, or has
no impact.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use netdev_alloc_skb for buffer allocation to allow for headroom.
This prevents bugs in code paths that assume extra space at the
front and makes sky2 behave like other drivers.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code to handle cloned skb overwriting is unnecessary in the
sky2 driver and is buggy. The bug is that pskb_expand_head can change the
skb but the driver has already mapped in the header.
Since the sky2 hardware doesn't need to overwrite memory, the buggy
code can just be removed; it was mistakenly copied from the tg3
driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch sets the floor of wireless level (signal) and noise at
-110 dBm, which makes them be comatible with RCPI, as discussed by
Simon Barber. With this change, bcm43xx-softmac and bcm43xx-d80211
behave the same.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ayaz Abdulla