Replace dev_kfree_skb with dev_kfree_skb_any in bnad_start_xmit that
can be called in hard irq and other contexts.
dev_kfree_skb_any is used as bnad_start_xmit only frees skbs when to
drop them, normally transmitted packets are handled elsewhere.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udelay() does not work on some architectures for values above
2000, in particular on ARM:
ERROR: "__bad_udelay" [drivers/net/ethernet/brocade/bna/bna.ko] undefined!
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit "fe1624c bna: RX Filter Enhancements" disables
VLAN tag stripping if the NIC is in promiscuous mode. This causes
__vlan_hwaccel_put_tag() is called when the stripping is disabled.
Because of this VLAN over bna does not work and causes BUGs in conjunction
with openvswitch like this:
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Rasesh Mody <rmody@brocade.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'make namespacecheck' to code that could be declared static.
After that remove code that is not being used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
> as reported for linux-next of Dec.20, 2013
> when CONFIG_NEED_DMA_MAP_STATE is not enabled:
>
> drivers/net/ethernet/brocade/bna/bnad.c: In function 'bnad_start_xmit':
> drivers/net/ethernet/brocade/bna/bnad.c:3074:26: error: 'struct bnad_tx_vector' has no member named 'dma_len'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes change to enable firmware patch simplication feature.
This feature is targeted to address the requirement to have independent patch
release for firmware. Prior to the 3.2.3.0 firmware, releasing a patch fix for
firmware would require changes to bna driver, to use new firmware images.
However with these changes, if the new firmware is flashed on to the Adapter,
the driver will use the new firmware after checking the patch release byte in
the firmware version.
Update the f/w version to 3.2.3.0
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Store the length of the skb buffer mapped along with the handle and use it
while unmapping the buffer.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- When bnad_setup_tx() returns NULL, the error is NOT returned to the caller.
The caller will incorrectly assume success. So Return ENOMEM when bna_tx_create()
fails.
- If bnad_tx_msix_register() fails, call bna_tx_destroy() to free tx & to NULL
the bnad reference to tcb.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we already check to see whether the BNAD_TXQ_TX_STARTED cleared.
But if the tcb structure which contains this flag is also already freed by that
time, we would dereference the NULL pointer. This patch is to check tcb for NULL
pointer, before dereferencing it.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Valid bit check for completion needs read fence, so that it does not get
reordered with other loads.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Prefetch header in GRO path. This reduces napi_frags_skb time from 9% to 5%.
- Changed the configurable limit of RxQ depth to 16384 (was 2048).
- bnad_rx_unmap_q elements are cachealigned.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CT2 HW supports multi-buffer Rx. This patch provides the necessary changes
for bnad to use multi-buffer Rx feature. For BNAD, multi-buffer Rx is by
default enabled when MTU is > 4096. For >4096 MTU, q0 data/large buffers are of
2048 size. As the resource requirements of multi-buffer Rx are different new Rx
needs to be created to use this feature. ASIC posts multiple completions if
frame exceeds buffer size. The last completion is marked with EOP flag.
- Separate HQ and DQ enums for resource allocations and configurations.
- rx_config and rxq structure changes to pass the correct info from bnad.
- DQ depth need not be same as HQ depth. So CQ depth is adjusted accordingly.
- Rx CFG frame size is taken from configured MTU.
- Rx q0 buffer size is configured from bnad s rx_config when multi-buffer is
enabled.
- Poll for entire frame completion.
- Once EOP completion is received gather the number of vectors used by the
frame to submit it to the stack.
- Changed MTU to frame size wherever necessary.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Added bna_rx_ucast_listset() for synchronous ucast listadd operation.
- Clear mac->handle before adding it to free_q.
- bnad_set_rx_mode() rewritten. bnad_set_rx_mode() adds the MACs in uc_list
to UCAM. If it exceeds the max supported, DEFAULT mode is turned on. If
MCAM limit is exceeded, ALLMULTI mode is turned on.
- Clear CF flags, check for the new mode and reprogram the Rx approach.
- Added bnad_set_rx_ucast_fltr() and bnad_set_rx_mcast_fltr().
- Check for IFF_PROMISC to set the correct mode.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- bna_rx_mcast_listset() API first looks at free_q only and not at other
pending Qs rendering it non-deterministic of giving an upper limit.
Modify bna_rx_mcast_listset() implementation to not use only half of the
limit.
- Allocate and initialize queue for deleting
- Segregate the adding and deleting process by using separate queues.
- The filter framework in bna does not let adding addresses to its max capacity
due to asynchronous operations involved.
Provide a synchronous option to set a given list.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add APIs to set and get IOC currnet fw state and alt IOC fw state
- bfa_ioc_ct_set_cur_ioc_fwstate()
- bfa_ioc_ct_get_cur_ioc_fwstate()
- bfa_ioc_ct_set_alt_ioc_fwstate()
- bfa_ioc_ct_get_alt_ioc_fwstate()
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Invoke skb_tx_timestamp() API just before invoking txq_doorbell()
- Add ethtool (-T) support
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
*using_dac = true;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err)
goto release_regions;
}
This means we only try and set the coherent DMA mask if we failed to
set a 32-bit DMA mask, and only if both fail do we fail the driver.
Adjust this so that if either setting fails, we fail the driver - and
thereby end up properly setting both the DMA mask and the coherent
DMA mask in the fallback case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the firmware to address the thermal notification issue
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bna_rx_sm_stop_wait_entry(), bna_rx_sm_rxf_stop_wait_entry(),
bna_rx_sm_started_entry(), bna_rx_sm_cleanup_wait_entry(),
and bna_rx_sm_cleanup_wait() are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1423:1: warning: symbol 'bna_rx_sm_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1476:1: warning: symbol 'bna_rx_sm_rxf_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1532:1: warning: symbol 'bna_rx_sm_started_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1597:1: warning: symbol 'bna_rx_sm_cleanup_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1602:1: warning: symbol 'bna_rx_sm_cleanup_wait' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you copy some code, you are supposed to read it. If nothing else,
there's a chance to spot and fix an obvious bug instead of sharing it...
X-Song: "I Got It From Agnes", by Tom Lehrer
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Tom Lehrer? You're dating yourself, Al ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
User should not be allowed to delete base function of eth port. Add a new field
to the bfa ioc attributes structure to indicate if the given ioc is default
function on the port or not.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure of the UCAST set for base mac address fails when user configures a
duplicate mac address that matches that of another vNIC on the same port.
The bna does not handle the ucast failure and keeps this address in cache.
On disable of the vNIC, bna tries to delete the failed base mac address and the
fw asserts.
On failure of ucast address, mark ucast address set to false.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver configuration flags are retained across open/stop operations preventing
configurations to be set in next open/stop. Setting MTU on a 1020 causes
network to fail until a reboot is performed on the host.
Clear the flags when configuration resets in hardware.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing iounmap() before return from bnad_init()
in the error handling case.
Introduced by commit 01b54b1451
(bna: tx rx cleanup fix).
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is declared to take u32 but definition uses enum.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Added Stats clear counter to the bfi_enet_stats_mac structure and
ethtool stats
- Modified the firmware naming convention to contain the firmware image
version (3.1.0.0). The new convention is
<firmware-image>-<firmware-version>.bin The change will enforce loading
only compatible firmware with this driver and also avoid over-writing
the old firmware image in-order to load new version driver as the
firmware names used to be the same.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- BNA state machine for Rx in start_wait state moves it to stop_wait on
receipt of RX_E_STOP. In Rx stop_wait state, on receipt of
RX_E_STARTED event does enet stop
RX_E_STOPPED event does rx_cleanup_cbfn
rx_cleanup_cbfn in this case is called without post_cbfn. post_cbfn
happens only after RX_E_STARTED event is received in start_wait. Without
doing post_cbfn, NAPI remains disabled and in cleanup we try to disable
again causing endless wait. ifconfig process and other workers can thus
get stuck.
- Introducing start_stop_wait state for Rx. This state handles the case of
if post_cbfn is not done simply do stop without the cleanup.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
Enhanced support for GRO. Page-base allocation method for Rx buffers is
used in GRO. Skb allocation has been removed in Rx path to use always warm-cache
skbs provided by napi_get_frags.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
For Tx IB, IPM was enabled with inter_pkt_timeo of 0. This caused the
Tx IB not to generate interrupt till inter_pkt_count of packets have been
received. Correct definition for BFI_TX_INTERPKT_TIMEO & BFI_TX_INTERPKT_COUNT
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Have contiguous queue pages for TxQ, RxQ and CQ. Data structure and
QPT changes related to contiguous queue pages
- Optimized Tx and Rx unmap structures. Tx and Rx fast path changes due to
unmap data structure changes
- Re-factored Tx and Rx fastpath routines as per the new queue data structures
- Implemented bnad_txq_wi_prepare() to program the opcode, flags, frame_len
and num_vectors in the work item
- Reduced Max TxQ and RxQ depth to 2048 while default value for Tx/Rx queue
depth is unaltered (512)
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Remove unnecessary prefetch
- Simplify checking & comparison of CQ flags
- Dereference & store unmap_array, unmap_cons & current unmap_array
element only once
- Make structures tx_config & rx_config cache line aligned.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Rasesh Mody <rmody@brocade.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These calls are followed by calls to memcpy() on the same memory area, so they
can safely be removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC can't see that in all non-error-return paths we do in fact
set *using_dac to something.
Add an explicit initialization to remove this warning:
drivers/net/ethernet/brocade/bna/bnad.c: In function ‘bnad_pci_probe’:
drivers/net/ethernet/brocade/bna/bnad.c:3079:5: warning: ‘using_dac’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/brocade/bna/bnad.c:3233:7: note: ‘using_dac’ was declared here
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment. Delete a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu