This allows e100 to be configured to append the
Ethernet FCS to the skb.
Useful for sniffing networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Need to use the new 'saddr' variable not the void 'addr' in
set_mac_address().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver xmit function is not allowed to change skb without special
care.
mlx4_en_xmit() should not call skb_reset_mac_header() and instead should
use skb->data to access ethernet header.
This removes a dumb test : if (ethh && ethh->h_dest)
Also remove this slow mlx4_en_mac_to_u64() call, we can use
get_unaligned() to get faster code.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename e1000e_reload_nvm() to e1000e_reload_nvm_generic() to signify the
function is used for more than one MAC-family type, and set and use it as a
MAC ops function pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove reference to non-existant function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_config_collision_dist() to
e1000e_config_collision_dist_generic() to signify the function is used for
more than one MAC-family type, and set and use it as a MAC ops function
pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call the MAC ops setup_physical_interface function pointer instead of the
MAC-family-specific function to conform to the rest of the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace e1000_check_reset_block() inline function with calls to the PHY ops
check_reset_block function pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace e1000_check_mng_mode() inline function with calls to the MAC ops
check_mng_mode function pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_setup_link() to e1000e_setup_link_generic() to signify the
function is used for more than one MAC-family type. The 82571-family has
a custom setup_link function which also calls the generic function. The
ich8lan-family has a custom function which should just be called via the
function pointer. The 80003es2lan-family just uses the generic function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_id_led_init() to e1000e_id_led_init_generic() to signify the
function is used for more than one MAC-family type. For the ich8lan MAC
family, some MACs use the generic function and others use the function
e1000_id_led_init_pchlan(). In all cases where e1000e_id_led_init() was
called directly, change to call the function pointer to be consistent with
the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When pre-allocating skbs for received packets, we set ip_summed =
CHECKSUM_UNNCESSARY. We used to change it back to CHECKSUM_NONE when
the received packet had an incorrect checksum or unhandled protocol.
Commit bc8acf2c8c ('drivers/net: avoid
some skb->ip_summed initializations') mistakenly replaced the latter
assignment with a DEBUG-only assertion that ip_summed ==
CHECKSUM_NONE. This assertion is always false, but it seems no-one
has exercised this code path in a DEBUG build.
Fix this by moving our assignment of CHECKSUM_UNNECESSARY into
efx_rx_packet_gro().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM instead
of custom code.
Use memcpy to set the address to dev->dev_addr in set_mac_address,
instead of mxing it up in a for loop with printing a debug msg.
Check also if the given address is valid.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_<level> for printk
Use temporary instead of multiple pr_conts
Coalesce formats.
Save a few bytes of object code too:
$ size drivers/net/ethernet/intel/e1000/e1000_main.o*
text data bss dec hex filename
60507 369 14120 74996 124f4
drivers/net/ethernet/intel/e1000/e1000_main.o.new
60717 369 14176 75262 125fe
drivers/net/ethernet/intel/e1000/e1000_main.o.old
Removed printing of pktdata.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Separate a complicated bit of e1000_config_dsp_after_link_change
into a new static function e1000_1000Mb_check_cable_length.
Reduces indentation and adds a bit of clarity.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent discussions on LKML, kernel-janitors, linux-wireless and netdev
have suggested boolean comparisons should use logical operators instead of
equality comparisons with true/false.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive the Ethernet FCS
and pass it up the stack, allowing sniffers and
other interested programs to inspect the FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to receive packets with bad FCS and
Runts, which can help when sniffing.
NOTE: r8169, at least on my NIC, silently drops packets
with bad FCS instead of counting them. It seems they are
only received in any fashion if the RxCRC flag is set
(which this patch allows).
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to pass the Ethernet FCS on up
the stack, and is useful when sniffing networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to receive Runts and frames with bad
Ethernet Frame Checksums (FCS).
Useful to sniffing & diagnosing bad networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to pass the Ethernet Frame Checksum
(FCS) up the stack. Useful when sniffing packets.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Good for testing the RX logic for bad CRC handling.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive all frames available, including
those with bad FCS, un-matched vlans, ethernet control frames,
and more.
Tested by sending frames with bad FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This can aid with testing the RX logic for bad
CRCs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables enabling/disabling reception of the Ethernet
FCS. This can be useful when sniffing packets.
For e1000e, enabling RXFCS can change the default
behaviour for how the NIC handles CRC. Disabling RXFCS
will take the NIC back to defaults, which can be configured
as part of the module options.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a regression that was introduced by
commit 0a5f384677
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
This patch reverts commit 0a5f384677
and instead issues warnings only if cpdma_chan_submit returns -ENOMEM.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Hegde, Vinay <vinay.hegde@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CLKDIV bitfield in the MDIO Control Register is a 16 bit field,
therefore the CLKDIV value may range from 0 to 0xffff.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
chan->chan_num is 0..CPDMA_MAX_CHANNELS-1 for tx channels and
CPDMA_MAX_CHANNELS..2*CPDMA_MAX_CHANNELS-1 for rx channels. However,
the rx and tx teardown registers expect zero based channel numbering.
Since the upper bits of the registers are reserved, the teardown also
worked before, this patch is cleanup only.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will prevent double free in some cases where be_clear() is called
for cleanup when be_setup() fails half-way.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a part of be_close(), instead of waiting for a max of 200ms for each TXQ,
wait for a total of 200ms for completions from all TXQs to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery involves ring cleanup and re-creation. The worker
thread must not run during EEH cleanup/resume.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch seeks to clean up the timer related code. It begins by
moving one-time timer setup code from tg3_open() to tg3_init_one().
It then creates a function that encapsulates the code needed to start
the timer. A tg3_timer_stop() function was added for parity. Finally,
this patch moves all the timer functions to a more suitable location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error happens in the tx completion thread, tg3_reset_task will be
scheduled and TX_RECOVERY_PENDING will be set. The TX_RECOVERY_PENDING
flag causes tg3_poll[_msix] to return early before doing much of its
work. Tg3_reset_task() gets canceled when the configuration of the
device is changing, which always results in a chip reset. When this
happens, the TX_RECOVERY_PENDING flag may be left set, which would
unnecessarily hinder tg3_poll from doing work. This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_phy_copper_begin() has code that configures the link
advertisements through the use of the link_config.speed and
link_config.duplex members. The driver does not internally use these
members in this way, nor is it (currently) permitted via the ethtool
interface. This patch removes the dead code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver tried to detect link changes by comparing the tg3 local
active_speed member with SPEED_UNKNOWN (or formerly SPEED_INVALID).
This check is not correct, since phylib will never set its speed member
to either of these two values. The code only appeared to work because
tg3 initializes active_speed to SPEED_INVALID during tg3_init_one. This
patch introduces a new "old_link" tg3 member and then compares the
phy_device's link member against it to detect link state changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Greear