We used to assume that even numbered threads were the primary
threads, ie those that would be listed and started as a cpu from
open firmware. Replace a left over is even (% 2) check with a check
for it being a primary thread and update the comments.
Tested with a debug print on pseries, identical code found for cell.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
64 bit powerpc requires the kexec user space tools avoid overwriting
the static kernel image and translation hash table when choosing
where to put memory image data because it copies the data into place
using the kernels virtual memory system. Kexec userspace determines
these and other areas blocked by reading properties the kernel adds,
but does not filter these properties when creating the device tree
for the next kernel.
When the second kernel tries to add its values for these properties,
the export via /proc/device-tree is hidden by the pre-existing but
stale values from the flat tree. Kexec userspace reads the old
property, allocates the new kernel at the old kernel's end, and
gets rejected by the overlap check.
Search and remove these stale properties before adding the new values.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are no users of PPC_MERGE in tree so we can get rid of it.
It was a hold over from the arch/ppc days.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are two issues when we enable CONFIG_RELOCATABLE. The first is due
to the fact that phys_addr_t is now defined in linux/types.h. The second
is due to the fact that the DMA code changes expose memstart_addr to
prom_init.c
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This target is needed to build cuImages with an embedded ramdisk image.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed, when trying to use, e.g.,
node = find_node_by_prop_value(prev, "booleanprop", "", 0))
to search for all nodes with a certain boolean property, that memcmp()
returns garbage when comparing zero bytes. It should return zero.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adjust amount to reserve based on previous nodes for reserves spanning
multiple nodes. Check if the node active range is empty before attempting
to pass the reserve to bootmem. In practice the range shouldn't be empty,
but to be sure we check.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The issue is the SPU code is not holding the kernel mutex lock while
adding samples to the kernel buffer.
This patch creates per SPU buffers to hold the data. Data
is added to the buffers from in interrupt context. The data
is periodically pushed to the kernel buffer via a new Oprofile
function oprofile_put_buff(). The oprofile_put_buff() function
is called via a work queue enabling the funtion to acquire the
mutex lock.
The existing user controls for adjusting the per CPU buffer
size is used to control the size of the per SPU buffers.
Similarly, overflows of the SPU buffers are reported by
incrementing the per CPU buffer stats. This eliminates the
need to have architecture specific controls for the per SPU
buffers which is not acceptable to the OProfile user tool
maintainer.
The export of the oprofile add_event_entry() is removed as it
is no longer needed given this patch.
Note, this patch has not addressed the issue of indexing arrays
by the spu number. This still needs to be fixed as the spu
numbering is not guarenteed to be 0 to max_num_spus-1.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Acked-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
"unsigned int" speed cannot be negative, it's thus pointless
to test if it is.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pfn of the memory to be removed should be validated prior to
attempting to remove the memory. In cases where the probe of a
memory section fails during hotplug add, the pfn for the lmb may
not be valid.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the vmlinux binary in memory is larger than 4 MiB than it collides
with the initial boot code which is linked at 4 MiB in case of cuBoot.
If the the uncompressed image size (on disk size) is less than 4 MiB
then it would fit. The difference between those two sizes is the bss
section. In cuBoot we have the dtb embedded right after the data
section so it is very likely that the reset of the bss section (in
kernel's start up code) will overwrite the dtb blob. Therefore we
reallocate the dtb. Something similar is allready done to the initrd.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a comment to clarify why atomic_dec_if_positive is being used
to decrement gang's aff_sched_count on SPU context unbind.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This patch improves redability of the code responsible for trying to find
a node with enough SPUs not committed to other affinity gangs.
An additional check is also added, to avoid taking into account gangs that
have no SPU affinity.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
With most file readers (eg cat, dd), reading a context's regs file will
result in two reads: the first to read the data, and the second to
return EOF. Because each read performs a spu_acquire_saved, we end up
descheduling and re-scheduling the context twice.
This change does a simple check to see if we'd return EOF before
calling spu_acquire_saved(), saving the extra schedule operation.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, read() on the sputrace log will block until the read buffer
is full. This makes it difficult to retrieve the end of the buffer, as
the user will need to read with the right-sized buffer.
In a similar method as 91553a1b5e0df006a3573a88d98ee7cd48a3818a, this
change makes the switch_log return if there has already been data
read.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we use ctx->mapping_lock and ctx->switch_log->lock for the
context switch log. The mapping lock only prevents concurrent open()s,
so we require the switch_lock->lock for reads.
Since writes to the switch log buffer occur on context switches, we're
better off synchronising with the state_mutex, which is held during a
switch. Since we're serialised througout the buffer reads and writes,
we can use the state mutex to protect open and release too, and
can now kfree() the log buffer on release. This allows us to perform
the switch log notify without taking any extra locks.
Because the buffer is only present while the file is open, we can use
it to prevent multiple simultaneous openers.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, read() on the sputrace buffer will only return data when
the user buffer is exhausted. This may mean that we never see the
end of the event log, unless we read() with exactly the right-sized
buffer.
This change makes sputrace_read not block if we have data ready to
return.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, sputrace will start logging to the event buffer before the
log buffer has been open()ed. This results in a heap of "lost samples"
warnings if the sputrace file hasn't yet been opened.
Since the buffer is reset on open() anyway, there's no need to enable
logging when no-one has opened the log.
Because open clears the log, make it return EBUSY for mutliple open
calls.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This patch adds support for the GPIO functions of PPC40x and PPC44x
SOCs.
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cuboot wrapper for the AMCC PowerPC 405EZ Acadia board. The
clocking code is derived from U-Boot, originally written by Stefan Roese.
Signed-off-by: Josh Boyer <jwboyer@linux.ibm.com>
This adds a common board file for almost all of the "simple" PowerPC 40x
boards that exist today. This is intended to be a single place to add
support for boards that do not differ in platform support from most of the
evaluation boards that are used as reference platforms. Boards that have
specific requirements or custom hardware setup should still have their own
board.c file.
The first board ported to this is the AMCC PowerPC 405EZ Acadia board.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display
This adds the basic platform support to build from.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
MPC5200 needs to have pipelining disabled for ATA to work. MPC5200B does not.
So, for the latter, don't touch the original setting from the bootloader.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current device trees do not have the device_type = soc property set
anymore. Fix up the cuImage bootwrapper fragment to still find the IMMR
nodes.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patchset removes some dead code and creates a platform device
for the RTC class driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patchset removes some dead code and creates a platform device
for the RTC class driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below changes register_pci_controller() such that controllers
being added after pcibios_init() has run are be scanned immediately.
This is needed for example by the BCM47xx PCI controller, which is located
on the SSB bus, which is now initialized after the PCI subsystem.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the reset button of WGT634U machine, using
GPIO interrupts. Based on a patch from Michel Lespinasse.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch simplifies the BCM47xx GPIO code by using the new SSB GPIO
API, which does a lot things that were implemented directly in the
BCM47xx code.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the remaining reference to the BCM947xx development
board codename.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds a printk message when a WGT634U machine is detected.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
... and move it to where all its brothers and sisters reside. Requested by
Shane McDonald <mcdonald.shane@gmail.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most if not all x86 platforms have an RTC device, but sometimes the RTC
is not exposed as a PNP0b00/PNP0b01/PNP0b02 device in PNPBIOS or ACPI:
http://bugzilla.kernel.org/show_bug.cgi?id=11580https://bugzilla.redhat.com/show_bug.cgi?id=451188
It's best if we can discover the RTC via PNP because then we know
which flavor of device it is, where it lives, and which IRQ it uses.
But if we can't, we should register a platform device using the
compiled-in RTC_PORT/RTC_IRQ resource assumptions.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Rik Theys <rik.theys@esat.kuleuven.be>
Reported-by: shr_msn@yahoo.com.tw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently, indirect_pci was changed to test if the bus number requested
is the one hanging straight off the PHB, then it substitutes the bus
number with another one contained in a new "self_busno" field of the
pci_controller structure.
However, this breaks CHRP which didn't initialize this new field, and
which relies on having the right bus number passed to the hardware.
This fixes it by initializing this variable properly for all CHRP bridges
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The detection of the IBM "Python" PCI host bridge on IBM CHRP
machines such as old RS6000 was broken when we changed
of_device_is_compatible() from strncasecmp to strcasecmp (dropped
the "n" variant) due to the way IBM encodes the chip version.
We fix that by instead doing a match on the model property like
we do for others bridges in that file. It should be good enough
for those machines. If yours is still broken, let me know.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
prom_init was changed to take a new argument, the address
where the kernel is loaded, which is now used to copy the
SMP spin loop down before use.
However, only head_64.S was adapted to pass this new value,
not head_32.S, thus breaking SMP boot on 32-bit SMP CHRP
machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new merged DMA code will try to access isa_bridge_pcidev when
trying to DMA to/from legacy devices. This is however only defined
on 64-bit. Fixes this for now by adding the variable, even if it
stays NULL. In the long run, we'll make isa-bridge.c common to
32 and 64-bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the powerpc PCI layer is not configured to re-assign everything,
it currently fails to detect that a PCI to PCI bridge has been left
unassigned by the firmware and tries to allocate resource for the
default window values in the bridge (0...X) (with the notable exception
of a hack we have in there that detects some Apple firmware unassigned
bridge resources).
This results in resource allocation failures, which are generally
fixed up later on but it causes scary warnings in the logs and we
have seen the fixup code fall over in some circumstances (a different
issue to fix as well).
This code improves that by providing a more complete & useful function
to intuit that a bridge was left unassigned by the firmware, and thus
force a full re-allocation by the PCI code without trying to allocate
the existing useless resources first.
The algorithm we use basically considers unassigned a window that
starts at 0 (PCI address) if the corresponding address space enable
bit is not set. In addition, for memory space, it considers such a
resource unassigned also if the host bridge isn't configured to
forward cycles to address 0 (ie, the resource basically overlaps
main memory).
This fixes a range of problems with things like Bare-Metal support
on pSeries machines, or attempt to use partial firmware PCI setup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
..
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
..>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If CONFIG_PROC_FS is not set, I get:
| arch/m68k/kernel/ints.c:433: error: redefinition of 'init_irq_proc'
| include/linux/interrupt.h:438: error: previous definition of 'init_irq_proc' was here
This was introduced by commit 6168a702ab
("Declare init_irq_proc before we use it."), which replaced the #ifdef
protection of the init_irq_proc() call by a static inline dummy if
CONFIG_PROC_FS is not set.
Make init_irq_proc() depend on CONFIG_PROC_FS to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the no longer used m68k PCI code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milton Miller