LDPC is enabled by the rate control if the its determined
that the target peer supports LDPC. We would have already
intersected the HT capabilities so if our peer supports
LDPC so do we.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LDPC will be enabled through the rate control algorithm
for each buffer the the tx_info flags.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a function to clean up tx status ring.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable CRC check on the descriptor fetched from host on AR9003
upon reseting the TX queue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also reset tx status ring suring chip reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9002 hardware code enables aggregation for WEP but
mac80211 doesn't enable aggregation with WEP, and the AR9003
code family does not need this so skip it for now for AR9003
but leave the code and annotate we should eventually consider
how to remove this in consideration for the HAL unification
goals.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asynch fifo code is specific to >= AR9287 so stuff it
into the AR9002 hardware family code and skip it for AR9003
cards.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is done depending on what the EEPROM settings indicates.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add this now as OFDM spur mitigation required accessing
the EEPROM for the AR9003 devices.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once upon a time the AR_EEPROM_MAC macro was added to let us
add a random attribute to the three 4-bytes of MAC addresses
entries we read from the EEPROM. This was good while a random
high-enough value was used which did not conflict with any
of the already existing enum eeprom_param values. With AR9003
support the enums overlap and it means we either increment
the random offset or just restore the reading logic to match
what the HAL has. I choose to do the later to synchronize
the logic on both code bases.
This should fix reading the MAC address from the EEPROM
on AR9003 hardware.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is so we can share routines which access this register
on calib.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also move interrupt related code to mac.c
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 TX/RX gain is currently initialized with the other
components, so for now AR9003 does not implment this callback,
after hardware bring up we can test moving the TX/RX gain there
as well and if it works well move them to its own callback as
well.
Since all INI stuff is now moved out hw.c no longer needs to
include and touch any original INI headers/structs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is specific to the AR9002 family only.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move out the generic hardware family code out into their own
files, we have one for AR5008, AR9001, and AR9002 family (ar9002_hw.c)
and another file for the new AR9003 hardware family (ar9003_hw.c).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration code touches phy registers and since these
change the calibration code needs to be abstracted.
Noise floor calibration is the only thing remaining but
since the remaining calls only touch the AR_PHY_AGC_CONTROL
register we'll just define that register conditionally, that
will be done separately. The goal is to remove the dependency
of ar9002_phy.h on calib.c
This also adds stubs to be filled for AR9003 calibration code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration settings should go into the respective
hardware family AR9002 calibration settings callback,
ar9002_hw_init_cal_settings().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can do the family revision check on the top level caller.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're bailing out on the alternative code path so remove the
else branch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Open Loop Control temperature compensation changes between our
hardware so use a helper for it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code can be simplified and shared between two locations if we bring
this into a helper. During reset we do not account for the skip count.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan