Use gpio_request_array() / gpio_free_array(), this makes the code
cleaner and less error prone.
This patch also properly frees GPIOs in case ata_host_activate() call fails.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
In FSL sata v2 block, the snoop bit of PRDT Word3 description
information is at bit28 instead of bit22.
This patch adds FSL sata v2 probe and resolve this difference.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1b4b:91a3 seems to be another PCI ID for marvell ahci. Add it.
Reported and tested in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1068354
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-by: Alessandro Tagliapietra <tagliapietra.alessandro@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before
the transport layer instructs the link layer to transmit HOLDS. Note that it
can take some time for the HOLDs to get to the other end, and that in the
interim there must be enough room in the FIFO to absorb all data that could
arrive.
Update the new recommended value to 16.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When a single device error is detected, the device under the error
is indicated by the error bit set in the DER. There is a one to one
mapping between register bit and devices on Port multiplier(PMP)
i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device
1 etc.
Current implementation treats Device error register value as device
number not set of bits representing multiple device on PMP. It is
changed to consider bit level.
No need to check for each set bit as all command is going to be
aborted.
Signed-off-by: Ashish Kalra <B00888@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some DMA controllers (eg: drivers/dma/dw_dmac*) allow platform specific
configuration for dma transfers. User drivers need to set chan->private field
of channel with pointer to configuration data. This patch takes dma_priv data
from platform data and passes it to chan->private_data, in order to pass
platform specific configuration to DMAC controller.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 40d69ba029
("pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)")
used pr_<level>.
Add #define pr_fmt and remove DRV_NAME.
Increment driver version numbers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.
Currently driver supports only True IDE mode.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds ata_sff_queue_work() & ata_sff_queue_delayed_work() routine in
libata-sff.c file. This routine can be used by ata drivers to use ata_sff_wq.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds an updated SATA RAID DeviceID for the Intel Patsburg PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 6b7ae9545a (libata: reimplement link power
management) removed the check of ATA_FLAG_LPM but neglected to remove the flag
itself. Do it now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These flags are marked as obsolete and the checks for them have been removed
by commit 294440887b (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver makes use of the two options (CONFIG_SATA_DWC_[V]DEBUG) to enable
the debug output but they both are absent in drivers/ata/Kconfig...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver erroneously uses ata_get_cmd_descript() not only for printing out
the ATA commands but also the protocol and DMA direction enums. Add functions
for properly printing those out...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The caller expects this function to return the DMA channel number on success,
while it returns 0...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the following compilation errors/warnings:
drivers/ata/sata_dwc_460ex.c:43:1: warning: "DRV_NAME" redefined
In file included from drivers/ata/sata_dwc_460ex.c:38:
drivers/ata/libata.h:31:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c:44:1: warning: "DRV_VERSION" redefined
drivers/ata/libata.h:32:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_exec_command_by_tag':
drivers/ata/sata_dwc_460ex.c:1356: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1476: warning: `err' is used uninitialized in this
function
drivers/ata/sata_dwc_460ex.c:1465: note: `err' was declared here
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1493: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_prep':
drivers/ata/sata_dwc_460ex.c:1537: error: `tag' undeclared (first use in this
function)
drivers/ata/sata_dwc_460ex.c:1537: error: (Each undeclared identifier is
reported only once
drivers/ata/sata_dwc_460ex.c:1537: error: for each function it appears in.)
NB: error only happens if DEBUG_NCQ macro is defined...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Somehow the driver was committed with a bare number for the PIO mask, instead
of ATA_PIO4...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Right at the moment, the libata error handler is incredibly
monolithic. This makes it impossible to use from composite drivers
like libsas and ipr which have to handle error themselves in the first
instance.
The essence of the change is to split the monolithic error handler
into two components: one which handles a queue of ata commands for
processing and the other which handles the back end of readying a
port. This allows the upper error handler fine grained control in
calling libsas functions (and making sure they only get called for ATA
commands whose lower errors have been fixed up).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SCSI host eh_cmd_q should be protected by the host lock (not the
port lock). This probably doesn't matter that much at the moment,
since we try to serialise the add and eh pieces, but it might matter
in future for more convenient error handling. Plus this switches
libata to the standard eh pattern where you lock, remove from the cmd
queue to a local list and unlock and then operate on the local list.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host. For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code. However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone). Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths. This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_eh_analyze_serror() suppresses hotplug notifications if LPM is
being used because LPM generates spurious hotplug events. It compared
whether link->lpm_policy was different from ATA_LPM_MAX_POWER to
determine whether LPM is enabled; however, this is incorrect as for
drivers which don't implement LPM, lpm_policy is always
ATA_LPM_UNKNOWN. This disabled hotplug detection for all drivers
which don't implement LPM.
Fix it by comparing whether lpm_policy is greater than
ATA_LPM_MAX_POWER.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Right at the moment, the libata error handler is incredibly
monolithic. This makes it impossible to use from composite drivers
like libsas and ipr which have to handle error themselves in the first
instance.
The essence of the change is to split the monolithic error handler
into two components: one which handles a queue of ata commands for
processing and the other which handles the back end of readying a
port. This allows the upper error handler fine grained control in
calling libsas functions (and making sure they only get called for ATA
commands whose lower errors have been fixed up).
Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The SCSI host eh_cmd_q should be protected by the host lock (not the
port lock). This probably doesn't matter that much at the moment,
since we try to serialise the add and eh pieces, but it might matter
in future for more convenient error handling. Plus this switches
libata to the standard eh pattern where you lock, remove from the cmd
queue to a local list and unlock and then operate on the local list.
Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host. For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code. However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone). Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.
Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths. This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page. This
is achieved by setting queue DMA alignment. If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.
This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors(). Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.
This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size. While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVR-212D can't do SETXFER like its sibling DVRTD08. Add
ATA_HORKAGE_NOSETXFER for it. Reported in bko#27502.
https://bugzilla.kernel.org/show_bug.cgi?id=27502
Signed-off-by: Francesco Antonacci <fraanto@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 5f173107ec added HFLAG_YES_FBS workaround for 88SE9128
(1b4b:9123).
However, that change inadvertently caused the legacy IDE interface of
the controller (with the same pci id) to become associated with the AHCI
driver as well, causing the driver to try to bring the interface up in
vain.
Fix that by matching against class as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ab81a505ae (pata_hpt37x: unify ->pre_reset
methods) neglected to remove the initializer for the prereset() method from
'hpt374_fn1_port_ops' (it's inherited from 'hpt372_port_ops' anyway), as well
as to update the comment in hpt37x_init_one()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the AHCI-mode SATA DeviceID for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hpt37x_init_one() has a large *if* statement which should really be folded into
the *switch* statement that currently constitutes its *else* branch, reducing
one level of indentation...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
... the same as the 'pata_hpt366' driver does.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_mpc52xx supports BMDMA but inherits ata_sff_port_ops which
triggers BUG_ON() when a DMA command is issued. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_HAVE_PATA_PLATFORM, by virtue of where its defined, has a
dependency on CONFG_ATA and CONFIG_ATA_SFF. This causes Kconfig
warnings when it is selected by various architectures, such as
warning: (ARCH_VEXPRESS && <choice> || ARCH_RPC && <choice> || MACH_VPAC270 && ARCH_PXA || MACH_REALVIEW_PB11MP && ARCH_REALVIEW || MACH_REALVIEW_PBA8 && ARCH_REALVIEW || MACH_REALVIEW_PBX && ARCH_REALVIEW || MACH_BAST_IDE && ARCH_S3C2410 || MACH_ANUBIS && ARCH_S3C2410) selects HAVE_PATA_PLATFORM which has unmet direct dependencies (ATA && ATA_SFF)
Since this option is only used to control visibility of the
CONFIG_PATA_PLATFORM option and isn't itself visible in the menu,
it is straightforward to simply remove these dependencies rather
than adjust all the architectures.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver clearly tries to limit HPT370[A] to UltraDMA/66 if the PCI clock is
less than 50 MHz but due to cut&paste type mistake this code has no effect...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix 8 errors and 3 warnings given by checkpatch.pl:
- *switch* and *case* not on the same indentation level;
- no space between *for*/*switch*/*while* and open parenthesis;
- space between an unary operator and its operand;
- spaces before tabs;
- lines over 80 characters.
In addition to these changes, also do the following:
- add new line after variable definitions;
- fix the style of some multi-line comments.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix 12 errors and 15 warnings given by checkpatch.pl:
- *switch* and *case* not on the same indentation level;
- no space between *for*/*switch*/*while* and open parenthesis;
- space between an unary operator and its operand;
- drive blacklist arrays not being *const*;
- spaces before tabs;
- lines over 80 characters.
In addition to these changes, also do the following:
- add new line after variable definitions;
- fix the style of some multi-line comments.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix 2 errors and 11 warnings given by checkpatch.pl:
- *switch* and *case* not on the same indentation level;
- no space between *switch* and open parenthesis;
- drive blacklist arrays not being *const*;
- spaces before tabs;
- lines over 80 characters.
In addition to these changes, also add new line after variable definition in
hpt36x_init_chipset()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Lucas De Marchi