Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T3 firmware only supports one WRs worth of page list for fast register
work requests. The driver currently allows 2 WRs worth, which
doesn't work for T3, so reduce the limit in the driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current MTT allocator uses kmalloc() to allocate a buffer for its
buddy allocator, and thus is limited in the amount of MTT segments
that it can control. As a result, the size of memory that can be
registered is limited too. This patch uses a module parameter to
control the number of MTT entries that each segment represents,
allowing more memory to be registered with the same number of
segments.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a task did not complete normally due to a TMF, libiscsi will
now complete the task with the state ISCSI_TASK_ABRT_TMF. Drivers
like bnx2i that need to free resources if a command did not complete normally
can then check the task state. If a driver does not need to send
a special command if we have dropped the session then they can check
for ISCSI_TASK_ABRT_SESS_RECOV.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.
I think there are two problems with this.
1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.
2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.
Fixes for cxgb3i from Karen Xie.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered. So use trylock and syscall_restart to avoid this
deadlock.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix increment, i is incremented one past 10K/5K before the
loop ends, so the error messages will be displayed too soon if the
test succeeds on the last iteration. Fix the comparisons to be >
instead of >=.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The queue map for flush completion circumvention is only used for
kernel space queue pairs. This patch skips the allocation of the
queue maps in case the QP is created for userspace. In addition, this
patch does not iomap the galpas for kernel usage if the queue pair is
only used in userspace. These changes will improve the performance of
creation of userspace queue pairs.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In case of large queue pairs there is the possibillity of allocation
failures due to memory fragmentation when using kmalloc(). To ensure
the memory is allocated even if kmalloc() can not find chunks which
are big enough, we fall back to allocating the memory with vmalloc().
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To improve performance of driver resource allocation, replace
vmalloc() calls with kmalloc().
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The low-level mlx4 driver modified the page-list addresses for fast
register work requests post send to big-endian, and set a "present"
bit. This caused problems later when the consumer attempted to unmap
the pages using the page-list (using the list addresses which were
assumed to be still in CPU-endian order). Fix the mlx4 driver to
allocate two buffers and use a private buffer for the hardware-format
bus addresses.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1571>,
an NFS/RDMA server crash. The cause of the crash was found by Vu Pham
of Mellanox. The fix is along the lines suggested by Steve Wise in
comment #21 in bug 1571.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the SQ is flushed, mark the flushed entries as not signaled so
the poll logic doesn't re-insert the CQ entry thinking its an out of
order completion.
The bug can cause the NFS/RDMA server to crash due to processing the
same completed work request twice.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If reg_phys_mem() fails, we need to free memory allocated for MPA
frame with private data before returning the error. Also move
nes_add_ref() after the reg_phys_mem() is successful.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Running large cluster setup, we are hanging after many hours of
testing. Fixing this required going over the code and making sure the
rexmit entry was properly removed based on the cm_node's state and
packet received. Also when receiving a FIN packet, check seq# and
make sure there were no errors before calling handle_fin().
Following are the changes done in nes_cm.c:
* handle_ack_pkt() needs to return error value, so in case of error,
handle_fin() is not called. Some cleanup done while going over the code.
* handle_rst_pkt(), handling of cm_node's NES_CM_STATE_LAST_ACK is missing.
* process_packet(), in case of FIN only packet is received, call
check_seq() before processing.
* in handle_fin_pkt(), we are calling cleanup_retrans_entry() for all
conditions, even if the packets need to be dropped.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under heavy load with large cluster testing, it may take longer to
receive a response to MPA requests. Change the driver to wait longer
after each rexmit to max time value.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
check_seq() was not checking if the seq#s have wrapped. Fix it.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connect request comes, apbvt should only be set for
non-loopback connections.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the NES_DEBUG that is causing the compile warning about an
unused variable when INFINIBAND_NES_DEBUG is not enabled.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/sys/class/infiniband/nes?/fw_ver is not displaying firmware version
properly (it shows 0.0.0 with the current code). Fill in the correct
firmware version number.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With updated PHY firmware for SFP_D, setting the trace length to 1
inch for SFP_D provides a more stable link.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable repause timer for port 1. Without this setting, under stress,
the chip may misbehave.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In commit 1b949324 ("RDMA/nes: Fix SFP+ PHY initialization") there is
a mistake in the clean up code that removed port 1 CDR loop filter
settings for 10G cards other than CX4. Put the correct setting back
for appropriate PHY types.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change thermo mitigation code to flip the SerDes1 reference clock to
internal, to match the change in commit a4849fc1 ("RDMA/nes: Add
wide_ppm_offset parm for switch compatibility").
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In error paths where a CQ is not created, pbl is not freeed properly.
In nes_destroy_cq(), add the corresponding check for nescq->mcrqf to
not call nes_free_resource() when it is already done in nes_create_cq().
Signed-off-by: Miroslaw Walukiewicz <miroslaw.walukiewicz@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commands INIT_HCA, CLOSE_HCA, SYS_EN, SYS_DIS, and CLOSE_IB all have 1
second timeouts. For INIT_HCA this causes problems when had more than
2^18 are QPs configured, since the command takes more than 1 second to
complete.
All other commands have 60-second timeouts. This patch makes the
above commands consistent with the rest of the commands (and with the
chip documentation).
This patch is an expansion of a patch from Arthur Kepner
<akepner@sgi.com> fixing just the INIT_HCA timeout.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
QP attributes must stay initialized when moving back to IDLE. Zeroing
them will crash the system in _flush_qp() if the QP is subsequently
moved to ERROR and back to IDLE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code incorrectly failed memory registration if the buffer was not
page aligned. Also, the length field is mangled causing the hardware
to think the registration is much larger than it really is.
The fix is to remove the page alignment restriction as well the
incorrect length adjustment. Also make sure that all buffers after
the first start at a page boundary, and all buffers except the last
end on a page boundary.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Initialize pbl_count_256 to 0 to get rid of the warning:
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_reg_mr':
drivers/infiniband/hw/nes/nes_verbs.c:1955: warning: 'pbl_count_256' may be used uninitialized in this function
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If NAPI is enabled while IPoIB's CQ is being drained, it creates a
race on priv->ibwc between ipoib_poll() and ipoib_drain_cq(), leading
to memory corruption.
The solution is to enable/disable NAPI in ipoib_ib_dev_{open/stop}()
instead of in ipoib_{open/stop}(), and sync NAPI on the INITIALIZED
flag instead on the ADMIN_UP flag. This way NAPI will be disabled when
ipoib_drain_cq() is called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1587>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
NFS/RDMA currently fails to set up connections if peer2peer is on.
This is due to the fact that the NFS/RDMA client sets its ORD to 0.
If peer2peer is set, make sure the active side ORD is >= 1 and the
passive side IRD is >=1.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new register settings for new SFP+ PHY/firmware.
Add new PHY to to nes_netdev_get/set_settings.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have observed unstable link with a new BNT switch.
Add wide_ppm_offset parameter to allow the user to control the clock
ppm offset on the CX4 interface for better compatibility. Default is
100ppm, setting it to 1 will increase it to 300ppm. Change default
SerDes1 reference clock to external source.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SFP+ PHY initialization has very long delays, incorrect settings for
direct attach copper cables, and inconsistent link detection.
Adjust delays to the minimum required by the PHY. Worst case is now
less than 4 seconds. Add new register settings for direct attach
cables. Change link detection logic to use two new registers for more
consistent link state detection. Reorganize code to shorten line
length.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We are getting crash or hung situation when we are running network
cable pull tests during RDMA traffic.
In schedule_nes_timer(), we return an error if nes_nic_cm_xmit()
returns failure. This is changed to success as skb is being put on
the timer routines to be processed later. In send_syn() case, we are
indicating connect failure once from nes_connect() and the other when
the rexmit retries expires.
The other issue is skb->users which we are incrementing before calling
nes_nic_cm_xmit() which calls dev_queue_xmit() but in case of failure
we are decrementing the skb->users at the same time putting the skb on
the rexmit path. Even if dev_queue_xmit() fails, the skb->users is
decremented already. We are removing the decrement of skb->users in
case of failure from both schedule_nes_timer() as well as from
nes_cm_timer_tick().
There is also extra check in nes_cm_timer_tick() for rexmit failure
which does a break from the loop is removed. This causes problem as
the other nodes have their cm_node->ref_count incremented and are not
processed.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix issues found by static code analysis:
(1) Check if cm_node was successfully created for loopback connection.
(2) schedule_nes_timer() does not free up allocated memory after
encountering an error. There is a WARN_ON() for this condition.
(3) there is a cm_node->freed flag which is set but not used.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The were some incorrect casts to unsigned long that caused 64-bit values
to be truncated on 32-bit architectures and made the driver pass invalid
adresses and lengths to the hardware. The problems were primarily seen
with kernels with highmem configured but some could show up in
non-highmem kernels, too.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When doing rdma_resolve_addr(), if the relevant IB port is down, the
function fails and the cm_id is not bound to the correct device.
Therefore, application does not have a device handle and cannot wait
for the port to become active. The function fails because the
underlying IPoIB interface is not joined to the broadcast group and
therefore the SA does not have a multicast record to take a Q_Key
from.
The fix is to use lazy Q_Key resolution - cma_set_qkey() will set
id_priv->qkey if it was not set, and will be called just before the
Q_Key is really required.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When joining an IPoIB multicast group, use the same rate as in the
broadcast group. Otherwise, if the RDMA CM creates this group before
IPoIB does, it might get a different rate. This will cause IPoIB to
fail joining to the same group later on, because IPoIB uses strict
rate selection.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have to release the RTNL before calling free_netdev() so that the
device state has a chance to become NETREG_UNREGISTERED. Otherwise
when removing a child interface, we hit the BUG() that tests the
device state in free_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cxgb3 l2t entry, hwtid, and dst entry were being released before
all the iwch_ep references were released. This can cause a crash in
t3_l2t_send_slow() and other places where the l2t entry is used.
The fix is to defer releasing these resources until all endpoint
references are gone.
Details:
- move flags field to the iwch_ep_common struct.
- add a flag indicating resources are to be released.
- release resources at endpoint free time instead of close/abort time.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eric Dumazet