ISAPNP, PNPBIOS, and ACPI describe the "possible resource settings" of
a device, i.e., the possibilities an OS bus driver has when it assigns
I/O port, MMIO, and other resources to the device.
PNP used to maintain this "possible resource setting" information in
one independent option structure and a list of dependent option
structures for each device. Each of these option structures had lists
of I/O, memory, IRQ, and DMA resources, for example:
dev
independent options
ind-io0 -> ind-io1 ...
ind-mem0 -> ind-mem1 ...
...
dependent option set 0
dep0-io0 -> dep0-io1 ...
dep0-mem0 -> dep0-mem1 ...
...
dependent option set 1
dep1-io0 -> dep1-io1 ...
dep1-mem0 -> dep1-mem1 ...
...
...
This data structure was designed for ISAPNP, where the OS configures
device resource settings by writing directly to configuration
registers. The OS can write the registers in arbitrary order much
like it writes PCI BARs.
However, for PNPBIOS and ACPI devices, the OS uses firmware interfaces
that perform device configuration, and it is important to pass the
desired settings to those interfaces in the correct order. The OS
learns the correct order by using firmware interfaces that return the
"current resource settings" and "possible resource settings," but the
option structures above doesn't store the ordering information.
This patch replaces the independent and dependent lists with a single
list of options. For example, a device might have possible resource
settings like this:
dev
options
ind-io0 -> dep0-io0 -> dep1->io0 -> ind-io1 ...
All the possible settings are in the same list, in the order they
come from the firmware "possible resource settings" list. Each entry
is tagged with an independent/dependent flag. Dependent entries also
have a "set number" and an optional priority value. All dependent
entries must be assigned from the same set. For example, the OS can
use all the entries from dependent set 0, or all the entries from
dependent set 1, but it cannot mix entries from set 0 with entries
from set 1.
Prior to this patch PNP didn't keep track of the order of this list,
and it assigned all independent options first, then all dependent
ones. Using the example above, that resulted in a "desired
configuration" list like this:
ind->io0 -> ind->io1 -> depN-io0 ...
instead of the list the firmware expects, which looks like this:
ind->io0 -> depN-io0 -> ind-io1 ...
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the resource list is empty, say that explicitly. Previously,
it was confusing because often the heading was followed by zero
resource lines, then some "add resource" lines from auto-assignment,
so the "add" lines looked like current resources.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
PNP used to have a fixed-size pnp_resource_table for tracking the
resources used by a device. This table often overflowed, so we've
had to increase the table size, which wastes memory because most
devices have very few resources.
This patch replaces the table with a linked list of resources where
the entries are allocated on demand.
This removes messages like these:
pnpacpi: exceeded the max number of IO resources
00:01: too many I/O port resources
References:
http://bugzilla.kernel.org/show_bug.cgi?id=9535http://bugzilla.kernel.org/show_bug.cgi?id=9740http://lkml.org/lkml/2007/11/30/110
This patch also changes the way PNP uses the IORESOURCE_UNSET,
IORESOURCE_AUTO, and IORESOURCE_DISABLED flags.
Prior to this patch, the pnp_resource_table entries used the flags
like this:
IORESOURCE_UNSET
This table entry is unused and available for use. When this flag
is set, we shouldn't look at anything else in the resource structure.
This flag is set when a resource table entry is initialized.
IORESOURCE_AUTO
This resource was assigned automatically by pnp_assign_{io,mem,etc}().
This flag is set when a resource table entry is initialized and
cleared whenever we discover a resource setting by reading an ISAPNP
config register, parsing a PNPBIOS resource data stream, parsing an
ACPI _CRS list, or interpreting a sysfs "set" command.
Resources marked IORESOURCE_AUTO are reinitialized and marked as
IORESOURCE_UNSET by pnp_clean_resource_table() in these cases:
- before we attempt to assign resources automatically,
- if we fail to assign resources automatically,
- after disabling a device
IORESOURCE_DISABLED
Set by pnp_assign_{io,mem,etc}() when automatic assignment fails.
Also set by PNPBIOS and PNPACPI for:
- invalid IRQs or GSI registration failures
- invalid DMA channels
- I/O ports above 0x10000
- mem ranges with negative length
After this patch, there is no pnp_resource_table, and the resource list
entries use the flags like this:
IORESOURCE_UNSET
This flag is no longer used in PNP. Instead of keeping
IORESOURCE_UNSET entries in the resource list, we remove
entries from the list and free them.
IORESOURCE_AUTO
No change in meaning: it still means the resource was assigned
automatically by pnp_assign_{port,mem,etc}(), but these functions
now set the bit explicitly.
We still "clean" a device's resource list in the same places,
but rather than reinitializing IORESOURCE_AUTO entries, we
just remove them from the list.
Note that IORESOURCE_AUTO entries are always at the end of the
list, so removing them doesn't reorder other list entries.
This is because non-IORESOURCE_AUTO entries are added by the
ISAPNP, PNPBIOS, or PNPACPI "get resources" methods and by the
sysfs "set" command. In each of these cases, we completely free
the resource list first.
IORESOURCE_DISABLED
In addition to the cases where we used to set this flag, ISAPNP now
adds an IORESOURCE_DISABLED resource when it reads a configuration
register with a "disabled" value.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
This patch adds a "pnp_resource_type_name(struct resource *)" that
returns the string resource type. This will be used by the sysfs
"show resources" function and the debug resource dump function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
In the debug resource dump, decode the flags and indicate when
a resource is disabled or has been automatically assigned.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Add a common hex array in hexdump.c so everyone can use it.
Add a common hi/lo helper to avoid the shifting masking that is
done to get the upper and lower nibbles of a byte value.
Pull the pack_hex_byte helper from kgdb as it is opencoded many
places in the tree that will be consolidated.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes more direct references to pnp_resource_table from the
pnp_assign_resources() path and the /sys user interface path.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds code to dump PNP resources before and after
assigning resources and before writing them to the device.
This is enabled by CONFIG_PNP_DEBUG=y.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Converting the EISA ID to a string is messy and error-prone, and
we might as well use the same code for ISAPNP and PNPBIOS.
PNPACPI uses the conversion done by the ACPI core with
acpi_ex_eisa_id_to_string().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These are manual fixups after running Lindent. No functional change.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seems pointless to require .c files to test CONFIG_PNP_DEBUG and
conditionally define DEBUG before including <linux/pnp.h>. Just test
CONFIG_PNP_DEBUG directly in pnp.h.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Bjorn Helgaas