As far as I know no M32R hardware actually has ISA slots.
And ISA drivers don't compile on M32R.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Remove the unused NOHIGHMEM option.
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: remove unneeded power_mutex lock in snd_pcm_drop
ALSA: fix locking in snd_pcm_open*() and snd_rawmidi_open*()
Delete ARM's own cnt32_to_63.h as the copy in include/linux/ should now be
used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty_find_polling_driver() routine did not correctly check the base
part of the tty name. This can lead to kgdboc selecting an incorrect
driver, as well as accepting a completely invalid tty such as "echo
ffff0 > /sys/module/kgdboc/parameters/kgdboc".
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
On x86_64 the gdb serial register structure defines the PS (also known
as eflags), CS and SS registers as 4 bytes entities.
This patch splits the x86_64 regnames enum into a 32 and 64 version to
account for the 32 bit entities in the gdb serial packets.
Also the program counter is properly filled in for the sleeping
threads.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The BX and DX registers in the gdb serial register packet need to be
flipped for gdb to receive the correct data.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
On the x86 arch, user space single step exceptions should be ignored
if they occur in the kernel space, such as ptrace stepping through a
system call.
First check if it is kgdb that is executing a single step, then ensure
it is not an accidental traversal into the user space, while in kgdb,
any other time the TIF_SINGLESTEP is set, kgdb should ignore the
exception.
On x86, arm, mips and powerpc, the kgdb_contthread usage was
inconsistent with the way single stepping is implemented in the kgdb
core. The arch specific stub should always set the
kgdb_cpu_doing_single_step correctly if it is single stepping. This
allows kgdb to correctly process an instruction steps if ptrace
happens to be requesting an instruction step over a system call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
On the ARM architecture, kgdb will crash the kernel if the last byte
of valid memory is written due to a flush_icache_range flushing
beyond the memory boundary.
Signed-off-by: Atsuo Igarashi <atsuo_igarashi@tripeaks.co.jp>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6:
UBIFS: fix printk format warnings
UBIFS: remove incorrect assert
UBIFS: TNC / GC race fixes
UBIFS: create the name of the background thread in every case
Yet another bug was found in xfs_iext_irec_compact_full() and while the
source of the bug was found it wasn't an easy task to track it down
because the conditions are very difficult to reproduce.
A HUGE thank-you goes to Russell Cattelan and Eric Sandeen for their
significant effort in tracking down the source of this corruption.
xfs_iext_irec_compact_full() and xfs_iext_irec_compact_pages() are almost
identical - they both compact indirect extent lists by moving extents from
subsequent buffers into earlier ones. xfs_iext_irec_compact_pages() only
moves extents if all of the extents in the next buffer will fit into the
empty space in the buffer before it. xfs_iext_irec_compact_full() will go
a step further and move part of the next buffer if all the extents wont
fit. It will then shift the remaining extents in the next buffer up to the
start of the buffer. The bug here was that we did not update er_extoff and
this caused extent list corruption.
It does not appear that this extra functionality gains us much. Calling
xfs_iext_irec_compact_pages() instead will do a good enough job at
compacting the indirect list and will be quicker too.
For the case in xfs_iext_indirect_to_direct() the total number of extents
in the indirect list will fit into one buffer so we will never need the
extra functionality of xfs_iext_irec_compact_full() there.
Also xfs_iext_irec_compact_pages() doesn't need to do a memmove() (the
buffers will never overlap) so we don't want the performance hit that can
incur.
SGI-PV: 987159
SGI-Modid: xfs-linux-melb:xfs-kern:32166a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
If we don't move all the records from the next buffer into the current
buffer then we need to update the er_extoff field of the next buffer as we
shift the remaining records to the start of the buffer.
SGI-PV: 987159
SGI-Modid: xfs-linux-melb:xfs-kern:32165a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Russell Cattelan <cattelan@thebarn.com>
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") changed how paths are flushed on an SM event. This
change introduces a problem if the path record query triggered by
fails, causing path->ah to become NULL. A later successful path query
will then trigger WARN_ON() in path_rec_completion(), and crash
because path->ah has already been freed, so the ipoib_put_ah() inside
the lock in path_rec_completion() may actually drop the last reference
(contrary to the comment that claims this is safe).
Fix this by updating path->ah and freeing old_ah only when the path
record query is successful. This prevents the neighbour AH and that
path AH from getting out of sync.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1194>
Reported-by: Rabah Salem <ravah@mellanox.com>
Debugged-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The power_mutex lock in snd_pcm_drop may cause a possible deadlock
chain, and above all, it's unneeded. Let's get rid of it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM and rawmidi open callbacks have a lock against card->controls_list
but it takes a wrong one, card->controls_rwsem, instead of a right one
card->ctl_files_rwlock. This patch fixes them.
This change also fixes automatically the potential deadlocks due to
mm->mmap_sem in munmap and copy_from/to_user, reported by Sitsofe
Wheeler:
A: snd_ctl_elem_user_tlv(): card->controls_rwsem => mm->mmap_sem
B: snd_pcm_open(): card->open_mutex => card->controls_rwsem
C: munmap: mm->mmap_sem => snd_pcm_release(): card->open_mutex
The patch breaks the chain.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the e1000/e1000e split, no hardware supported by e1000
supports packet split, just remove the Kconfig option and associated
code from the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following sparse warnings are being generated
because bonding.h is missing definitons for items
declared in bond_main.c but also used in bond_sysfs.h
Also export bond_dev_list as this is also declared
in bond_main but used elsewhere in drivers/net/bonding.
bond_main.c:105:20: warning: symbol 'bonding_defaults' was not declared. Should it be static?
bond_main.c:148:1: warning: symbol 'bond_dev_list' was not declared. Should it be static?
bond_main.c:162:22: warning: symbol 'bond_lacp_tbl' was not declared. Should it be static?
bond_main.c:168:22: warning: symbol 'bond_mode_tbl' was not declared. Should it be static?
bond_main.c:179:22: warning: symbol 'xmit_hashtype_tbl' was not declared. Should it be static?
bond_main.c:186:22: warning: symbol 'arp_validate_tbl' was not declared. Should it be static?
bond_main.c:194:22: warning: symbol 'fail_over_mac_tbl' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Netpoll will call the interrupt handler with interrupts
disabled when using kgdboe, so spin_lock_irqsave() should
be used instead of spin_lock_irq() to prevent interrupts
from being incorrectly enabled.
Signed-off-by: Weiwei Wang <weiwei.wang@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove
the dead code associated with !CONFIG_PPC_MERGE.
With this change the pre_request_irq() and post_free_irq() calls became
nops so they have been removed. Also removed fs_request_irq() and
fs_free_irq() and just called request_irq() and free_irq().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms so we don't need to depend on it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch will add the phy reset bit into the power up mask which is
used during power up. Certain BIOSes will place the phy in reset and
therefore the driver must take the phy out of reset when it loads.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With 2.6.27-rc3 I noticed the following messages in my boot log:
0000:01:00.0: 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:04:ff:09
The second seems correct, but the first has a silly repetition of the
PCI device before the actual message. The message originates from
e1000_eeprom_checks in e1000e/netdev.c.
With this patch below the first message becomes
e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
which makes it similar to directly preceding messages.
Use dev_warn instead of e_warn in e1000_eeprom_checks() as the interface
name has not yet been assigned at that point.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unneeded (struct atl1e_adapter *) casts, for hw->adapter
already has type atl1e_adapter *.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Recent changes to MII bus initialization code added exit points which
didn't free or iounmap the bus before returning.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11372.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reported-by: Daniel Marjamki <danielm77@spray.se>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Removing the module would cause a kernel oops as platform_driver_probe
failed to detect a device and unregistered the platform driver on module
init, and cleanup_module would unregister the already unregistered driver.
The suspend and resume functions weren't being called.
platform_driver support was added earlier, but without any
platform_device_register* calls I don't think it was being used. Now all
devices are registered using platform_device_register_simple and pointers
are kept to unregister the ones that the probe failed for or unregister
all devices on module shutdown. init_module no longer calls ne_init to
reduce confusion (and multiple unregister paths that caused the rmmod
oops). With the devices now registered they are added to the platform
driver and get suspend and resume events.
netif_device_detach(dev) was added before unregister_netdev(dev) when
removing the region as occationally I would see a race condition where the
device was still being used in unregister_netdev.
Signed-off-by: David Fries <david@fries.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The loop with the timeout used "while (... && timeout--)", which means
than when the timeout occurs, "timeout" will be -1 after the loop has
exited. The code that checks if the looped exited because of a timeout
used "if (timeout <= 0)". Seems ok, except timeout is unsigned, and
(unsigned)-1 isn't less than zero!
Using "--timeout" in the loop fixes this problem, as now "timeout" will be
0 when the loop times out.
This also fixes a bug in the existing code, where it will erroneously think
a timeout occurred if the condition the loop was waiting for is satisfied
on the final iteration before a timeout.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the driver fails to acquire the control flag used to serialize
NVM and PHY accesses between the driver, firmware and hardware, remove the
request for the flag otherwise the hardware might grant the flag when it
becomes available but the driver will not release the flag. This could
cause the firmware to prevent the driver getting the flag for all future
attempts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bug fix: don't set netdev->name early before netdev registration. Setting
netdev->name early with dev_alloc_name() would occasionally cause netdev
registration to fail returning error that device was already registered.
Since we're using netdev->name to name MSI-X vectors, we now need to
move the request_irq after netdev registartion, so move it to ->open.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bug fix: Free MSI intr with correct data handle
Use davem proposed naming for MSI-X tx/rx vectors (ethX-tx-0, ethX-rx-0)
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes for review items from Ben Hutchings:
- use netdev->net_stats rather than private net_stats
- use ethtool op .get_sset_count rather than .get_stats_count
- err out if setting Tx/Rx csum or TSO using ethtool and setting is
not enabled for device.
- pass in jiffies + constant to round_jiffies
- return err if new MTU is out-of-bounds
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
LRO is only applied to IPv4 pkts, so don't use the LRO indication functions
for anything other IPv4 pkts. Every non-IPv4 pkt is indicated using non-
LRO functions.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a wrong assignment in r6040_free_txbufs
on a receive skb pointer while we should actually do this
on the transmit skb pointer.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do not touch IFF_UP flag during qeth recovery, but invoke dev_close()
in case of failing recovery.
Cancel outstanding control commands in case of Data Checks or
Channel Checks.
Do not invoke qeth_l2_del_all_mc() in case of a hard stop to speed up
removal of qeth devices.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Real HiperSocket devices in layer2 mode have a firmware-created
MAC-address. This change enables the qeth driver to use this
firmware MAC-address for layer2 HiperSocket devices.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix mailing lists in two MAINTAINERS entries
i2c-dev: Return correct error code on class_create() failure
i2c-powermac: Fix section for probe and remove functions
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: prevent stale state of c1e_mask across CPU offline/online, fix
Make sched_clock() report time since boot rather than time since last
timer interrupt.
Make sched_clock() expand and scale the 32-bit TSC value running at
IOCLK speed (~33MHz) to a 64-bit nanosecond counter, using cnt32_to_63()
acquired from the ARM arch and without using slow DIVU instructions
every call.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move asm-arm/cnt32_to_63.h to include/linux/ so that MN10300 can make
use of it too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows reporting the link, checksum, and feature settings
of bonded device by using generic hooks.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Check if the link is available when a changed interrupt has been received and
set the carrier status appropriately. The code is copied nearly verbatim from
the dl2k module. The link status could be used in more places in the driver,
but this is enough to get the carrier status reported to userspace. Fixes
kernel bug #7487:
http://bugzilla.kernel.org/show_bug.cgi?id=7487
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adrian Bunk