* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Delete filenames/versions from comments.
I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.
While at it:
* Remove unused VERSION define from ide.c.
* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.
While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:
generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method
it821x.c:
* if memory allocation fails drive->autotune won't be set
(but there also won't be ->set_pio_mode method in such case)
piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)
However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.
* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
method may still override them).
* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.
While at it:
* Use ATA_{UDMA,MWDMA,SWDMA}* defines.
* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.
* serverworks.c: fix DMA masks being set before checking DMA base.
v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.
v2:
* Fix pmac_ide_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_rate_filter() calls from host drivers to IDE core.
* Make ide_rate_filter() static.
* Make 'speed' argument of ->speedproc const.
v2:
* Fix it8213_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ATA_PIO[0-6] defines to <linux/ata.h>.
* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.
* Add PIO masks to host drivers.
<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
and convert all users accordingly.
* Remove no longer needed ide_pio_data_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.
* Add IDE_HFLAG_SINGLE flag for single channel devices.
* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
and remove no longer needed ide_pci_device_t.channels field.
v2:
* Fix issues noticed by Sergei:
- correct code alignment in scc_pata.c
- s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter. Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.
Next patches add automatic detection of some systems using short cables.
Changes:
* Rename hwif->udma_four to hwif->cbl and make it u8.
* Convert all existing users accordingly (use ATA_CBL_* defines while at it).
* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().
* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
SWDMA modes are unsupported by it821x. Attempts to tune SWDMA modes always
fail (due to sanity check in ->speedproc) and result in PIO being tuned.
* Fix incorrect SWDMA mask so core code won't try these modes and will just
tune PIO if no other DMA modes are available.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
The DMA support for RAID mode broke after:
commit 71ef51cc17
Author: Jens Axboe <axboe@suse.de>
Date: Â Fri Jul 28 09:02:17 2006 +0200
  [PATCH] it821x: fix ide dma setup bug
  Only enable dma for a valid speed setting.
  Signed-off-by: Jens Axboe <axboe@suse.de>
commit 0a8348d086
Author: Jens Axboe <axboe@suse.de>
Date: Â Fri Jul 28 08:58:26 2006 +0200
  [PATCH] ide: if the id fields looks screwy, disable DMA
  It's the safer choice. Originally due to a bug in itx821x, but a
  generally sound thing to do.
  Signed-off-by: Jens Axboe <axboe@suse.de>
However it worked by pure luck before Jens' fixes: bogus ide_dma_enable()
usage in it821x driver combined with loosy check in ide_dma_verbose() allowed
the hardware to operate in DMA mode. When these problems were fixed the DMA
support broke...
The source root for the regression turned out to be that the it821x.c code
was clearing too much of id->field_valid. The IDE core code was using the
original value of id->field_valid to do the tuning but later DMA got disabled
in ide_dma_verbose() because of the incorrect id->field_valid fixup. Fix it.
While at it:
* Do fixup() after probing the drives but before tuning them (which is also
OK w.r.t. ide_undecoded_slave() fixup). This change fixes device IDENTIFY
data to be consistent before/after the tuning and allows us to remove extra
re-tuning of drives from it821x_fixups().
* Fake MWDMA0 enabled/supported bits in IDENTIFY data if the device has
DMA capable bit set (this is just to tell the IDE core that DMA is
supported since it821x firmware takes care of DMA mode programming).
* Don't touch timing registers and don't program transfer modes on devices
et all when in RAID mode - depend solely on firmware to do the tuning
(as suggested by Alan Cox and done in libata pata_it821x driver).
Thanks for testing the patch goes out to Thomas Kuther.
Cc: Thomas Kuther <gimpel@sonnenkinder.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.
* add ide_hwif_t.udma_filter hook for filtering UDMA mask
(use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
(loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()
v2:
* rename ->filter_udma_mask to ->udma_filter
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings
+ incorrect base clock being set for controller in the passthrough mode
* move code limiting max PIO according to the pair device capabilities from
config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also
applied for mode change requests coming through ->tuneproc and ->speedproc
interfaces
* set device speed in it821x_tuneproc()
* in it821x_tune_chipset() call it821x_tuneproc() also if the controller is
in the smart mode (so the check for pair device max PIO is done)
* rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc()
wrapper which does the max PIO mode check; it worked by the pure luck
previously, pio[4] and pio_want[4] arrays were used with index == 255
so random PIO timings and base clock were set for the controller in the
passthrough mode, thankfully PIO timings and base clock were corrected
later by config_it821x_chipset_for_pio() call (but it was not called for
PIO-only devices during resume and for user requested PIO autotuning)
* remove config_it821x_chipset_for_pio() call from config_chipset_for_dma()
as the driver sets ->autotune to 1 and ->tuneproc does the proper job now
* convert the last user of config_it821x_chipset_for_pio() to use
it821x_tuneproc(drive, 255) and remove no longer needed function
While at it:
* fix few comments
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Missing variable initialisation would mean it would sometimes not put ATAPI
devices into DMA by default.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <Jack.Lee@ite.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This lets you throw out the iteraid stuff that has ended up back in due
to stupid goings on in the IDE world. Its the same heavily tested code
shipped in Fedora/Red Hat products but without the other dependancies on
the Bartlomiej IDE layer.
Pre-requisite: the ide-disk patch I sent to handle pure LBA devices.
Obviously you lose things like hot unplug with the Bartlomiej IDE layer
at the moment but that won't matter to most users.
The patch does the following
- Add IT8211/12 to pci_ids.h
- Add Makefile/Kconfig entry
- Add it8212 driver
No core IDE code is touched by this diff
Embedded system testing and the ability to force raid mode off by David
Howells
Made possible by the ite reference code, documentation and also several
clarifications and pieces of assistance provided by ITE themselves
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bartlomiej Zolnierkiewicz