Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Limit the amount of address space claimed for Alchemy serial ports to
0x1000. On the Au1300, ports are only 0x1000 apart, and the registers
only extend to 0x110 at most on all supported alchemy models.
On the Au1300 the autodetect logic no longer works and this makes it
necessary to specify the port type through platform data. Because of
this the MSR quirk needs to be moved outside the autoconfig() function
which will no longer be called when UPF_FIXED_TYPE is specified.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not ignore the error returned by simple_config() / multi_config().
CC: linux-serial@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Currently the support for MPC5121 PSC UART in the mpc52xx_uart
driver is broken (only console pre-initialized by the bootloader
works). Re-enable it now by providing MPC5121 specific ops
for PSCx clock activation, FIFO controller init/uninit and
MPC5121 PSC FIFO shared interrupt handling functions.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When controlling an industrial radio modem it can be necessary to
manipulate the handshake lines in order to control the radio modem's
transmitter, from userspace.
The transmitter should not be turned off before all characters have been
transmitted. serial8250_tx_empty() was reporting that all characters were
transmitted before they actually were.
===
Discovered in parallel with more testing and analysis by Kees Schoenmakers
as follows:
I ran into an NetMos 9835 serial pci board which behaves a little
different than the standard. This type of expansion board is very common.
"Standard" 8250 compatible devices clear the 'UART_LST_TEMT" bit together
with the "UART_LSR_THRE" bit when writing data to the device.
The NetMos device does it slightly different
I believe that the TEMT bit is coupled to the shift register. The problem
is that after writing data to the device and very quickly after that one
does call serial8250_tx_empty, it returns the wrong information.
My patch makes the test more robust (and solves the problem) and it does
not affect the already correct devices.
Alan:
We may yet need to quirk this but now we know which chips we have a
way to do that should we find this breaks some other 8250 clone with
dodgy THRE.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Since sci_rxd_in() is used by SCI only, clean up
the header file by killing off code dealing with
SCIF ports and their register definitions.
Also introduce a default sci_rxd_in() function
which can be shared by all SCIF-only processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fmvj18x_cs, serial_cs:
add new id
Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quirk is applied on all cards with given manfid (is it that correct?).
Unfortunately, that quirk breaks resume on zaurus with billionton
bluetooth card inserted: c950ctrl is 0 and outb() faults.
I believe it is simply not a multiport card. (info->multi == 1). ...
... confirmed by printks.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since UCR1_UARTEN is defined 1, the port was always treated as enabled.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Oskar Schirmer <os@emlix.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In that situation if the old rate is invalid and the new rate is invalid
and the chip cannot do 9600 baud we report zero, which makes all the
drivers explode.
Instead force the rate based on min/max
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Perform a tricky suspend/resume even with no_console_suspend.
With no_console_suspend, kernel skips serial port suspend/resume and the
serial hardware may remain in undefined state after resume. It actually
happens on devices that don't have BIOS that handle serial
initialization. It makes impossible to use serial console after resume.
Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards
The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them
It allows to capture late console messages without breaking console
after resume.
This is just a resend of a patch discussed in these threads, as the
patch was not yet applied.
"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM
list, later LKML)
"serial-core: resume serial hardware with no_console_suspend" (Sep
15-Oct 18, 2009, LKML & ARM lists)
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wacom claims that the WACF namespace will always be devoted to serial
Wacom tablets. Remove the existing entries and add a wildcard to avoid
having to update the kernel every time they add a new device.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a new two finger touch Fujitsu Wacom Tablet PC.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems that in qemu, we can see an interrupt in R3 despite the
fact that it's masked in W1. The chip doesn't actually issue an
interrupt, but we can "see" it when taking an interrupt for the
other channel. This may be a qemu bug ... or not, so let's be
safe and avoid calling into the UART layer when that happens which
woulc cause a crash.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Landley <rob@landley.net>
The sh-sci driver used the wrong fifosize for PORT_SCIFA and PORT_SCIF
ports. If an incorrect size is used, the serial core will enforce an
early shutdown on the port, especially with baudrates < 9600.
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The console hangs during bootup when disable_irq is called from the
transmit interrupt handler (it will wait forever for it's "own"
interrupt in synchronize_irq). Fix by using disable_irq_nosync()
instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pcnet_cs,serial_cs:
add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctrl_xxx() is an antiquated SH interface, while __raw_xxx is the standard
API that accomplishes the same thing. As such, this converts the
remaining sh-sci straggles over, which enables the driver to be wired up
for ARM SH-Mobile CPUs as well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This establishes a sensible max baud rate for the earlyprintk cases where
the port's uartclk has not yet been determined.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Two IOC3 and IOC4 drivers have broken error paths on registration. Fix
them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several IOC3 and IOC4 drivers misuse the __devinit and __devexit section
markers. Use __init and __exit instead as appropriate, then add __devinit
and __devexit where they really belong for PCI drivers.
Also make ioc4_serial_init static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is V2 of early serial console support for the sh-sci
driver. The early serial console is using early platform
devices and "earlyprintk". To use this feature the early
platform devices must be broken out to one device per port
and the desired port should be selected on the kernel command
line like: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Do not read IIR in serial8250_start_tx when UART_BUG_TXEN
Reading the IIR clears some oustanding interrupts so it is not safe.
Instead, simply transmit immediately if the buffer is empty without
regard to IIR.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intel(R) PXA27x Processor Family Specification Update (Nov 2005)
says:
E75. UART: Baud rate may not be programmed correctly on
back-to-back writes.
Problem:
When programming the Divisor Latch registers, Low and High (DLL and
DLH), with back-to-back writes, the second register write may not
take effect. The result is an incorrect baud rate.
Workaround:
After programming the first Divisor Latch register, read and verify
it before programming the second Divisor Latch register.
This was hit when changing the baud rate from 115200 to 9600 while
receiving characters at 9600 Bd.
And fixed indention of some comments nearby.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding EEH handlers for the serial jsm driver. This patch adds
the PCI error handlers and also register them to be called when
a error is detected.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently there is a field in the jsm_board structure to cont
the number of interrupt that the card recevived, but it's not
working properly when the IRQ line is shared, and also nowhere
else this field is used. So, This patch is removing it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the jsm_channel->ch_wopen field is defined and never
used. So, this patch removes it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the field jsm_channel->ch_cpstime is defined but never
used, so this patch removes it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the field jsm_channel->ch_old_baud is not used, just
assigned in a lot of places but never used. This patches removes
this field.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the ch_custom_speed field exists but is never used,
so, this patch removes it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Actually jsm displays "Device Added" 8 times (for a 8 port device).
This silly patch just makes things more informative, showing
the port (instead of the device) that was added.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently jsm is showing the following message when loaded:
IRQ 432/JSM: IRQF_DISABLED is not guaranteed on shared IRQs
It's because the request_irq() is called using IRQF_DISABLED
and IRQF_SHARED.
Actually there is no need to use IRQF_DISABLED in this driver.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately, one cannot hold on to the struct firmware
that request_firmware_nowait() hands off, which is needed
in some cases. Allow this by requiring the callback to
free it (via release_firmware).
Additionally, give it a gfp_t parameter -- all the current
users call it from a GFP_KERNEL context so the GFP_ATOMIC
isn't necessary. This also marks an API break which is
useful in a sense, although that is obviously not the
primary purpose of this change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently serial ports on SH CPUs get disabled too early, because the
sci_tx_empty() routine claims to not be able to detect whether the
transmission has been completed and just always returns TIOCSER_TEMT. This
results in corrupt output of last characters if the port is not open for
reading at the same time. It is however possible to detect whether
transmission has been completed. Use the TEND bit of the status register
for this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function mcf_remove is used only wrapped by __devexit_p so define it
using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
There are a number of statements of the form A, B or A, B, C where
the numbers A,B,C are not consecutive. However, referencing [1] it
is the correct thing to replace these with A-B or A-C as apropriate.
[1] http://www.copyrightservice.co.uk/copyright/p03_copyright_notices
section 4iii 'Year of publication'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver missed a small API change while sitting in Ralf's tree, this
patch makes it compile again.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sh-sci code conditionalized the clock framework support in order to
give the other platforms a chance to catch up. sh64 supported this some
time ago and the forthcoming ARM changes handle this as well, this leaves
h8300 as the odd one out. H8300 has had since 2.5 to merge it's sh-sci
support upstream, and has yet to do so. At this point I will no longer be
holding back the driver to support an unreponsive architecture, 7 years
is quite enough of a grace period. Support is easily implemented on the
architecture if and when it ever decides to merge its changes upstream.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Finn Thain