Several sas drivers legitimately check the protocol against the union of
SAS_PROTOCOL_SATA and SAS_PROTOCOL_STP. Provide a SAS_PROTOCOL_STP_ALL
to silence warnings like:
drivers/scsi/pm8001/pm8001_sas.c:438:3: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:798:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:1783:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:1886:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/isci/request.c:3565:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the user has disabled CONFIG_SCSI_SAS_HOST_SMP then libsas drivers
will not be receiving smp-gpio frames and do not need this lookup code.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Tested-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.
Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation. Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written. If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.
Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:
smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The problem is that if we are doing a scsi scan then the device goes
into recovery then we will wait for the recovery to complete. It waits
because scsi-ml will send inquiries or report luns and the queueing code
will have been blocked due to the host not being ready. However, if we
are in recovery and then a scan is started the scan will silently fail
and some devices will not be added.
It is easy to hit the problem where devices do not show up with
FC where we are doing tests that disrupt the target controllers.
When the controller is disruprted (reboot, or setting firmware, etc),
and we cause the dev loss tmo to fire then devices will be removed
Then when the problem has been fixed, the rport will be scanned and
devices should be added back. But if we cause another disruption before
scanning has started then devices will not get added back. If the problem
is not started until the scan is started then the devices will be added
back.
This patch fixes that problem by not failing scans when the host
is in recovery. We will let scsi-ml send the IO and let the queueing
and scsi error handling deal with it like is done if we went into
recovery while scanning.
For recovery cases where the host is being torn down then with the
patch we will still fail the scan since there is not point in scanning.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new sysfs attr 'host_reset' in scsi_sysfs.c to
perform adapter or firmware reset as suggested by
Mike Christie here:
http://marc.info/?l=linux-scsi&m=127359347111167&w=2
user/application can write "adapter" or "firmware" on
this attr and it will call newly added function hook
in scsi_host_template to call LDD adapter or firmware
reset implementation.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Offload drivers like qla4xxx will offload the sending of the login/logout
pdus still, so this patch adds iscsi_conn_login_event which is
used by these types of drivers to notify userspace that the connection
has changed state.
It also adds a iscsi_is_session_online helper so the lld
can query the sessions state field.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to the iscsi class. There is only
1 request, the host vendor one, supported. It is expected that
this would be used for things like flash updates.
This patch is made over this one
http://marc.info/?l=linux-scsi&m=131149780020992&w=2
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set vlan priority and enable/disble a vlan.
Patch based on code from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We can replace the iface param mask with the
attr_is_visible callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A iscsi host can have multiple interfaces. This patch
adds a new iface iscsi class for this. It exports the
network settings now, and will be extended to also
export iscsi initiator port settings like the isid
and initiator name for drivers that can support multiple
initiator ports.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Export fcoe_get_wwn, fcoe_validate_vport_create and fcoe_wwn_to_str so that all
LLDs can use these common function.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ORE stands for "Objects Raid Engine"
This patch is a mechanical rename of everything that was in ios.c
and its API declaration to an ore.c and an osd_ore.h header. The ore
engine will later be used by the pnfs objects layout driver.
* File ios.c => ore.c
* Declaration of types and API are moved from exofs.h to a new
osd_ore.h
* All used types are prefixed by ore_ from their exofs_ name.
* Shift includes from exofs.h to osd_ore.h so osd_ore.h is
independent, include it from exofs.h.
Other than a pure rename there are no other changes. Next patch
will move the ore into it's own module and will export the API
to be used by exofs and later the layout driver
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the iscsi_sna_lt() and iscsi_sna_lte(), along with
iscsi_sna_gt() and iscsi_sna_gte() from iscsi_target_mod into
static inlines inside of include/scsi/iscsi_proto.h
This patch also includes the ISCSI_HDR_LEN and ISCSI_CRC_LEN
definitions.
(Added JesperJ simpliciation for iscsi_sna_* usage)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
struct scsi_lun is also just a struct with an array of 8 octets (64 bits)
but using it instead in iscsi structs lets us call scsilun_to_int
without a cast, and also lets us copy it using assignment, instead of
memcpy().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch renames the following iscsi_proto.h structures to avoid
namespace issues with drivers/target/iscsi/iscsi_target_core.h:
*) struct iscsi_cmd -> struct iscsi_scsi_req
*) struct iscsi_cmd_rsp -> struct iscsi_scsi_rsp
*) struct iscsi_login -> struct iscsi_login_req
This patch includes useful ISCSI_FLAG_LOGIN_[CURRENT,NEXT]_STAGE*,
and ISCSI_FLAG_SNACK_TYPE_* definitions used by iscsi_target_mod, and
fixes the incorrect definition of struct iscsi_snack to following
RFC-3720 Section 10.16. SNACK Request.
Also, this patch updates libiscsi, iSER, be2iscsi, and bn2xi to
use the updated structure definitions in a handful of locations.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The fcoe driver can implement ddp_targ() similarly to ddp_setup() when fcoe
stack works with existing target frame, e.g., tcm, where the ddp_targ() would
eventually point to the underlying hardware driver's implementation of
ndo_fcoe_ddp_targ() through net_device_ops. This new API sets up DDP context
for target appropriately by setting required bits for DDP context.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
struct scsi_lun is also just a struct with an array of 8 octets (64 bits)
but using it instead in iscsi structs lets us call scsilun_to_int
without a cast, and also lets us copy it using assignment, instead of
memcpy().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch converts target core and follwing scsi-misc upstream fabric
modules to use include/scsi/scsi_tcq.h includes for SIMPLE, HEAD_OF_QUEUE
and ORDERED SCSI tasks instead of scsi/libsas.h with TASK_ATTR*
*) tcm_loop: Convert tcm_loop_allocate_core_cmd() + tcm_loop_device_reset() to
scsi_tcq.h
*) tcm_fc: Convert ft_send_cmd() from FCP_PTA_* to scsi_tcq.h
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This allows a libsas driver to optionally provide a soft reset handler
for libata to drive. The isci driver allows software to control the
assertion/deassertion of SRST.
[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch converts target core and follwing scsi-misc upstream fabric
modules to use include/scsi/scsi_tcq.h includes for SIMPLE, HEAD_OF_QUEUE
and ORDERED SCSI tasks instead of scsi/libsas.h with TASK_ATTR*
*) tcm_loop: Convert tcm_loop_allocate_core_cmd() + tcm_loop_device_reset() to
scsi_tcq.h
*) tcm_fc: Convert ft_send_cmd() from FCP_PTA_* to scsi_tcq.h
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Commit c21e6beb removed our queue request_fn re-enter
protection, and defaulted to always running the queues from
kblockd to be safe. This was a known potential slow down,
but should be safe.
Unfortunately this is causing big performance regressions for
some, so we need to improve this logic. Looking into the details
of the re-enter, the real issue is on requeue of requests.
Requeue of requests upon seeing a BUSY condition from the device
ends up re-running the queue, causing traces like this:
scsi_request_fn()
scsi_dispatch_cmd()
scsi_queue_insert()
__scsi_queue_insert()
scsi_run_queue()
scsi_request_fn()
...
potentially causing the issue we want to avoid. So special
case the requeue re-run of the queue, but improve it to offload
the entire run of local queue and starved queue from a single
workqueue callback. This is a lot better than potentially
kicking off a workqueue run for each device seen.
This also fixes the issue of the local device going into recursion,
since the above mentioned commit never moved that queue run out
of line.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The xmit path can sleep with a page kmapped in the network
xmit code while it waits for space to open up, so we have to use
kmap instead of kmap atomic in that path.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During device discovery, scsi mid layer sends INQUIRY command to LUN
0. If the LUN 0 is not mapped to host, it creates a temporary
scsi_device with LUN id 0 and sends REPORT_LUNS command to it. After
the REPORT_LUNS succeeds, it walks through the LUN table and adds each
LUN found to sysfs. At the end of REPORT_LUNS lun table scan, it will
delete the temporary scsi_device of LUN 0.
When scsi devices are added to sysfs, it calls add_dev function of all
the registered class interfaces. If ses driver has been registered,
ses_intf_add() of ses module will be called. This function calls
scsi_device_enclosure() to check the inquiry data for EncServ
bit. Since inquiry was not allocated for temporary LUN 0 scsi_device,
it will cause NULL pointer exception.
To fix the problem, sdev->inquiry is checked for NULL before reading it.
Signed-off-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
both fcoe and bnx2fc drivers can access the common definition of
FCOE_MTU.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fc_fill_fc_hdr() expects fc_frame as an argument. Introduce __fc_fill_fc_hdr to
accept fc_frame_header as an argument.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This has cxgbi use the iscsi_conn_get_addr_param helper
and the get ep callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For drivers using the ep callbacks the addr and port
are attached to the endpoint instead of the conn.
This adds a callout to the iscsi_transport to get
ep values. It also adds locking around the get
param call to make sure that ep_disconnect does
not free the LLD's ep interconnect structs from
under us (the ep has a refcount so it will not
go away but the LLD may have structs from other
subsystems that are not allocated in the ep so
we need to protect them from getting freed).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This adds a helper to convert a addr struct to
a string. This will be used by the drivers in
the next patches.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The active variable on the iscsi_cls_conn is not used
so this patch removes it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When iscsid restarts it does not know the connection's
endpoint, so it is getting leaked. This fixes the problem
by having the iscsi class force a disconnect before a
new connection is bound.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To facilitate LLDDs to reuse the code, skb queue related functions are moved to
libfcoe, so that both fcoe and bnx2fc drivers can use them. The common structures
fcoe_port, fcoe_percpu_s are moved to libfcoe. fcoe_port will now have an
opaque pointer that points to corresponding driver's interface structure.
Also, fcoe_start_io and fcoe_fc_crc are moved to libfcoe.
As part of this change, fixed fcoe_start_io to return ENOMEM if
skb_clone fails.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables LLD to listen to rport events and perform LLD
specific operations based on the rport event. This patch also stores
sp_features and spp_type in rdata for further reference by LLD.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Dan Williams