Make the register offset table more maintainable.
From the 'sii-lbt' branch, which enables the LBT chip feature.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci: enable sg segment clustering
The specification states that ahci supports segments up to 4MiB in size,
so enable clustering.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->cbl == ATA_CBL_SATA indicates SATA cable while ap->flags &
ATA_FLAG_SATA indicates SATA host port. Till now they always gave the
same result but SATA/PATA bridge handling will change that. Switch to
ATA_FLAG_SATA test if we're testing for host port type.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement _GTM/_STM support. acpi_gtm is added to ata_port which
stores _GTM parameters over suspend/resume cycle. A new hook
ata_acpi_on_suspend() is responsible for storing _GTM parameters
during suspend. _STM is executed in ata_acpi_on_resume(). With this
change, invoking _GTF is safe on IDE hierarchy and acpi_sata check
before _GTF is removed.
ata_acpi_gtm() and ata_acpi_stm() implementation is taken from Alan
Cox's pata_acpi implementation. ata_acpi_gtm() is fixed such that the
result parameter is not shifted by sizeof(union acpi_object).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reimplements ACPI invocation such that, instead of
exporting ACPI details to the rest of libata, ACPI event handlers -
ata_acpi_on_resume() and ata_acpi_on_devcfg() - are used. These two
functions are responsible for determining whether specific ACPI method
is used and when.
On resume, _GTF is scheduled by setting ATA_DFLAG_ACPI_PENDING device
flag. This is done this way to avoid performing the action on wrong
device device (device swapping while suspended).
On every ata_dev_configure(), ata_acpi_on_devcfg() is called, which
performs _SDD and _GTF. _GTF is performed only after resuming and, if
SATA, hardreset as the ACPI spec specifies. As _GTF may contain
arbitrary commands, IDENTIFY page is re-read after _GTF taskfiles are
executed.
If one of ACPI methods fails, ata_acpi_on_devcfg() retries on the
first failure. If it fails again on the second try, ACPI is disabled
on the device. Note that successful configuration clears ACPI failed
status.
With all feature checks moved to the above two functions,
do_drive_set_taskfiles() is trivial and thus collapsed into
ata_acpi_exec_tfs(), which is now static and converted to return the
number of executed taskfiles to be used by ata_acpi_on_resume(). As
failures are handled properly, ata_acpi_push_id() now returns -errno
on errors instead of unconditional zero.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add missing LOCKING: and RETURNS: to function comment.
* Don't conditionalize warning messages with ata_msg_probe(). Print
directly with KERN_WARNING.
* Drop duplicate debug messages.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch cleans up ata_acpi_exec_tfs() and its friends.
* Rename taskfile_array to ata_acpi_gtf and make it __packed as it's
used as argument to ACPI method, and use pointer to ata_acpi_gtf and
number of taskfiles to represent _GTF taskfiles instead of a pointer
casted into unsigned long and byte count. This makes argument
re-checking in do_drive_set_taskfiles() unnecessary.
* Pointer in void * not in unsigned long.
* Clean up do_drive_get_GTF() error handling and make
do_drive_get_GTF() return number of taskfiles on success, 0 if _GTF
doesn't exist or doesn't contain valid ata. -errno on other errors.
* Remove superflous check for acpi->buffer.pointer.
* Update taskfile_load_raw() such that printed messages look similar
to the messages printed by ata_eh_report().
* s/do_drive_get_GTF/ata_dev_get_GTF/
s/do_drive_set_taskfiles/ata_dev_set_taskfiles/
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add acpi_handle to ata_host and ata_port. Rename
ata_device->obj_handle to ->acpi_handle and move it above such that
it doesn't get cleared on reconfiguration.
* Replace ACPI node association which ata_acpi_associate() which is
called once during host initialization. Unlike the previous
implementation, ata_acpi_associate() uses ATA_FLAG_ACPI_SATA to
choose between IDE or SATA ACPI hierarchy and uses simple child look
up instead of recursive walk to match the nodes. This is way safer
and simpler. Please read the following message for more info.
http://article.gmane.org/gmane.linux.ide/17554
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PIO4 is a maximum PIO mode supported by a driver. Using "255" as a max_mode
argument to ide_get_best_pio_mode() could result in wrong timings being used
by a driver (for "pio" equal to 5) or OOPS (for "pio" values > 5 && < 255).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reviewed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
The SiS966 has one additional PCI-ID 1180.
If the chipset is using this PCI-ID, the primary channel is connected to the
first PATA-port. The secondary channel is connected to SATA-ports in IDE
emulation mode. The legacy IO-ports are used.
The including of the PCI-ID into pata_sis is not sufficient, because the legacy
driver in drivers/ide is initialized before pata_sis.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In 7d12e780e0 David Howells performed
this evolution:
"IRQ: Maintain regs pointer globally rather than passing to IRQ handlers"
He correctly updated many of the function definitions that were using this
extra regs pointer parameter but forgot to update some caller sites of
those functions. The reason the modifications was not properly done on all
drivers is that some drivers were rarely compiled because they are for
AMIGA, or that some code sites were inside #ifdefs where the option is not
set or inside #if 0.
Here is the semantic patch that found the occurences
and fixed the problem.
@ rule1 @
identifier fn;
identifier irq, dev_id;
typedef irqreturn_t;
@@
static irqreturn_t fn(int irq, void *dev_id)
{
...
}
@@
identifier rule1.fn;
expression E1, E2, E3;
@@
fn(E1, E2
- ,E3
)
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we enable the SMCf010 IR device, the Toshiba Portege 4000 BIOS claims
the device is working, but it really isn't configured correctly. The BIOS
*will* configure it, but only if we call _SRS after (1) reversing the order
of the SIR and FIR I/O port regions and (2) changing the IRQ from
active-high to active-low.
This patch addresses the 2.6.22 regression:
"no irda0 interface (2.6.21 was OK), smsc does not find chip"
I tested this on a Portege 4000. The smsc-ircc2 driver correctly detects
the device, and "irattach irda0 -s && irdadump" shows transmitted and
received packets.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yeah, we could have just disabled it, but there's work on a new one that
isn't as fundamentally broken, so there really doesn't seem to be any
point in keeping it around.
The recent timer cleanup broke the only valid use, and when I say
"valid", I obviously mean "totally broken". So it's not like it works,
or really even can work in the current format that uses the unsafe
"panic" LED blinking routines..
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/ide/setup-pci.c: In function 'ide_scan_pcibus':
drivers/ide/setup-pci.c:879: warning: ignoring return value of '__pci_register_driver', declared with attribute warn_unused_result
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Recently the PLL input clock of Promise 2027x is sometimes detected
higher than expected (e.g. 20.027 MHz compared to 16.714 MHz).
It seems sometimes the mdelay() function is not as precise as it
used to be. Per Alan's advice, HT or power management might affect
the precision of mdelay().
This patch calls gettimeofday() to measure the time elapsed and
calculate the PLL input clock accordingly.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bahadir Balban <bahadir.balban@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
SWDMA modes are unsupported by it821x. Attempts to tune SWDMA modes always
fail (due to sanity check in ->speedproc) and result in PIO being tuned.
* Fix incorrect SWDMA mask so core code won't try these modes and will just
tune PIO if no other DMA modes are available.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* Driver can't skip programming transfer mode on the device in amd_set_drive()
(similar fix has been applied to via82cxxx driver ages ago).
* While at it remove redundant warning (ide_config_drive_speed() already
produces more valuable one).
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The HPT36x chips finally turned out to have the channel enable bits -- however,
badly implemented. Make use of them despite it's probably only going to burden
the driver's code -- assuming both channels are always enabled by the HighPoint
BIOS anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Cc: michal.kepien@poczta.onet.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add the MAXTOR STM3320620A drive into the UltraDMA/66 mode blacklist
for the HPT36x chips.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Found by a static analyser. It is in theory possible we dereference
dev->id when it has become invalid. Re-order to avoid this.
Not needed for new-ide as we no longer support the crazy exabyte nest stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Look at wait_drive_not_busy in drivers/ide/ide-taskfile.c:
static u8 wait_drive_not_busy(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
int retries = 100;
u8 stat;
/*
* Last sector was transfered, wait until drive is ready.
* This can take up to 10 usec, but we will wait max 1 ms
* (drive_cmd_intr() waits that long).
*/
while (((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) && retries--)
udelay(10);
if (!retries)
printk(KERN_ERR "%s: drive still BUSY!\n", drive->name);
return stat;
}
`printk' is never called because `retries' never holds zero at the
outside of `while' loop: when `retries' holds zero at the while's loop
condition, `retries' will hold -1 at the if condition.
Signed-off-by: Masatake YAMATO <jet@gyve.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: joe@perches.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
if the call to budget_register() fails in ttpci_budget_int(),
ttpci_budget_init() returns success. The attached patch will
fix this problem.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted and tested by Thomas Sattler <tsattler@gmx.de>.
cinergyT2.c does cancel_delayed_work() + flush_scheduled_work() while
holding cinergyt2->sem. This leads to deadlock because work->func()
needs the same mutex to complete. Another bug is that this code in fact
can't reliably stop the re-arming delayed_work.
Convert this code to use cancel_rearming_delayed_work() and move it
out of ->sem. Another mutex, ->wq_sem, was added to protect against the
concurrent open/resume.
This patch is a horrible hack to fix the lockup which happens in practice.
As Dmitry Torokhov pointed out this driver has other problems and needs
further changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l-info and other programs would loop indefinitely while querying the
tuners for cx88-blackbird cards.
The cause was that vidioc_g_tuner didn't return an error value for
qctrl->id != 0, making the application think there is a never ending
list of tuners...
This patch adds the same index check as done in vidioc_g_tuner() in
cx88-video.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If one uses a V4L *one* application, such as vlc or mplayer's v4l driver, as
the first user after the driver is loaded, the driver wedges itself and will
never capture properly. Even if one uses a V4L2 application later, it still
won't work.
If one uses a V4L *two* application first, such as tvtime or mplayer's v4l2
driver, then the driver will be ok. One can then run a V4L1 application, and
it will work.
It turns out the problem is with norm changing and the crop support that was
added in 2.6.21. The driver defaults to PAL, and keeps the last norm it was
set too across opens. If one changes the norm via V4L1, the cropping
parameters are not reset like they should be, and they'll remain broken across
device opens.
This patch removes the direct setting of btv->tvnorm in the V4L1 ioctl
VIDIOCSCHAN handler. The norm is set via the existing call to set_input(),
which calls set_tvnorm(), which will reset the cropping values now that it is
able to detect the norm change.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PCMCIA doesn't use DMA and as this driver is used on many platforms we
don't want it to fail on those that define the DMA alloc API as a NULL
return
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We got it backwards and now the other detects are fixed it shows up
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
host->irq and host->irq2 should be set before ata_host_register() for
IRQ reporting to work. Move up host->irq assignment in
ata_host_activate() and add it to ata_pci_init_one() native path and
pata_cs5520.
The port info printing in ata_host_register() doesn't fit all the
different controllers. It should probably be moved out to LLDs with
some helpers in the future.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to check for special case "acpi_osi=!Linux" before handling the
general case "acpi_osi=!*", or it will have no effect.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a page can't be allocated for the frag list of a skb, the code to
unmap the partially allocated list is off by one. For exaple, if
'frags' equals one, i == 0, and the alloc_page() fails, then the old
loop would have unmapped mapping[1] which is uninitialized. The same
would happen if the call to ib_dma_map_page() failed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Russell King wrote:
> Having upgraded from 2.6.16 to 2.6.22-rc6, I'm now seeing the following.
>
> Looks like netfilter is calling local_bh_enable() with IRQs disabled,
> which would appear to be illegal. Thankfully, this is a warn-once
> warning.
>
> WARNING: at /home/rmk/git/linux-2.6-rmk/kernel/softirq.c:138 local_bh_enable()
> [...]
> [<c01447fc>] (nf_conntrack_destroy+0x0/0x2c) from [<c012c05c>] (__kfree_skb+0xd0/0x100)
> [<c012bf8c>] (__kfree_skb+0x0/0x100) from [<c012c0d8>] (kfree_skb+0x4c/0x50)
> r5:c12a3800 r4:00000300
> [<c012c08c>] (kfree_skb+0x0/0x50) from [<bf03cbb0>] (el3_start_xmit+0xb8/0xd0 [3c589_cs])
> [<bf03caf8>] (el3_start_xmit+0x0/0xd0 [3c589_cs]) from [<c01324dc>] (dev_hard_start_xmit+0x1a8/0x244)
> r7:c12a3800 r6:c1a9aa00 r5:c1a9aa00 r4:c12a3800
> [<c0132334>] (dev_hard_start_xmit+0x0/0x244) from [<c013fcc0>] (__qdisc_run+0xb0/0x198)
Thats a bug in the 3c589_cs driver. Patch attached.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changed PATA handler for PATA-ports used by sata_sis.
This patch was originally submitted by Jeff Garzik.
Added PCI-ID 1180 for SiS966 Controller in pata_sis.
The 1180 mode is fully compatible to other SiS PATA-controller.
The PCI-ID 1183 is SATA in PATA-emulation, but not fully compatible
to SiS5513/5518. sata_sis.c is forwarding this ID to pata_sis.
1183 is not working if simply added to pata_sis.
This handling fixes issues with SiS968.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Another member of HTS5416* family doing spurious NCQ completion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Enrico Sardi <enricoss@tiscali.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_nv driver was missing the change_queue_depth hook in the SCSI host
template which the other NCQ-capable libata drivers had. This made it impossible
to change the queue depth by user request. Add this in.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_inic162x can't do LBA48 properly yet and is likely to corrupt
data on drives larger than LBA28 limit. Disable LBA48 devices during
device configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In ata_hsm_qc_complete():
Calling ata_altstatus() after the qc is completed might race with next qc. Remove it.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recently the PLL input clock of pata_pdc2027x is sometimes detected
higer than expected (e.g. 20.027 MHz compared to 16.714 MHz).
It seems sometimes the mdelay() function is not as precise as it
used to be. Per Alan's advice, HT or power management might affect
the precision of mdelay().
This patch calls gettimeofday() to mesure the time elapsed and
calculate the PLL input clock accordingly.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Mon, 11 Jun 2007 20:28:16 +0200 api wrote:
> Good day,
> When doing make menuconfig one comes across CONFIG_BLK_DEV_SD.
> The help file states that this is for scsi disks.NO MENTION IS MADE THAT
> IT IS NEEDE FOR SATA DISKS AS WELL!
> Would have saved me a lot of time if the help was up to date.
> I hope this can be changed so others can make a kernel for sata systems
> quicker.
From: Randy Dunlap <randy.dunlap@oracle.com>
Add help info for BLK_DEV_SD referring to its use in
SATA or PATA driver configurations.
Add help text for "ATA" indicating that it probably needs
some SCSI config symbols enabled in order to be useful.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resending patch 3/3 only.
These changes allow driver close routine to be called during module unload,
to clean-up buffers and other software resources, flush queues etc. Also,
hardware is reset to pristine state.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove an "sparse" warning about a shadowed variable name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the various access routines to access different
control and status settings present in different register locations.
This will fix problems related to working of different ports in
multi Port card.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen driver uses PCI function 0 to provide the functionality of MSI.
The patch makes driver check the bus master bit for function 0 and
enable it after the card initialization.
Signed-off-by: Dhananjay Phadke<dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik