ide_hwif_to_major[] has only 10 entries as there are 10 major numbers
reserved for IDE (if somebody needs more it shouldn't be hard to fix).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver crashes the kernel on HPT302N chips due to the missing initializer
for 'hpt302n.settings' having been unfortunately overlooked so far. :-<
Much thanks to Mike Mattie for pin-pointing the reason of crash.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add PCI ID for a newer variant of cardbus CF/IDE adapter card.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add "optical" to sysfs "media" attribute as already in /proc
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I get the following error messages when trying to open a CD device
(specifically, the Teac CD-ROM CD-224E) that has no media present:
hda: packet command error: status=3D0x51 { DriveReady SeekComplete Error }
hda: packet command error: error=3D0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
This happens when a "start stop unit" command (0x1b 0 0 0 3 0 0 0 0 0)
is sent to the drive to try to close the CD-ROM tray, but this drive
doesn't have that capability (it's a slim portable-type CD-ROM), so it
reports sense key 5 (illegal request) with asc/ascq 24/0. This is
exactly how SFF8090i says it should respond.
But ide-cd.c (in cdrom_decode_status() ) just sees sense key 5 and spews
out an error. It then goes on to request sense data, and
cdrom_log_sense() understands this error and doesn't log it.
The patch, for kernel 2.6.20.4, suppresses this error message.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[ bart: the ressurection of 2 years old patch which slipped thru the cracks
(thanks to Sergei Shtylyov for finding it) ]
These is the patch to turn on pdc202xx_new for ATAPI DMA. When testing, it
works fine without the (request_bufflen % 256) workaround as needed in libata.
ide-scsi filters out (pc->request_transfer % 1024) and use PIO, so the pdc202xx
ATAPI DMA problem is avoid. Both ide-cd and ide-scsi won't hit the ATAPI DMA
problem on pdc202xx_new.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since especially Serial ATA has it's own menu point now, I guess we can
change the description of the deprecated SATA driver as well, since the
new libATA subsystem is not configured through a SCSI low-level driver
anymore, but has it's own menu point.
From: Patrick Ringl <patrick_@freenet.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since hwif->ide_dma_check and hwif->ide_dma_on never queue any commands
(ide_config_drive_speed() sets transfer mode using polling and has no error
recovery) we are safe with setting hwgroup->busy for the time while DMA
setting for a drive is changed (so it won't race against I/O commands in fly).
I audited briefly all ->ide_dma_check/->ide_dma_on/->tuneproc/->speedproc
implementations and they all look OK wrt to this change.
This patch finally allowed me to close kernel bugzilla bug #8169
(once again thanks to Patrick Horn for reporting the issue & testing patches).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
"ide: fix drive side 80c cable check, take 2" patch from Tejun Heo (commit
fab59375b9) fixed 80c bit test (bit13 of word93)
but we also need to fix master/slave IDENTIFY order (slave device should be
probed first in order to make it release PDIAG- signal) and we should also
check for pre-ATA3 slave devices (which may not release PDIAG- signal).
[ Unfortunately the fact that IDE driver doesn't reset devices itself helps
only a bit as it seems that some BIOS-es reset ATA devices after programming
the chipset, some BIOS-es can be set to not probe/configure selected devices,
there may be no BIOS in case of add-on cards etc. ]
Since we are quite late in the release cycle and the required changes will
affect a lot of systems just revert the fix for now.
[ Please also see libata commit f31f0cc2f0. ]
Thanks goes out to Fernando Mitio Yamada for reporting the problem
and patiently testing patches.
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All modern distributions have been setting these options to "y" for ages.
(additionally "n" cases have been obsoleted for few years). Therefore use
DMA by default and remove CONFIG_IDEDMA_{ICS,PCI}_AUTO (also remove no longer
needed CONFIG_IDEDMA_AUTO). This fixes DMA support for rare configurations
where CONFIG_IDEDMA_{ICS,PCI}_AUTO was set to "n" but "hdparm -d 1" was used
to enable DMA support and which were forced to PIO mode by "ide: don't allow
DMA to be enabled if CONFIG_IDEDMA_{ICS,PCI}_AUTO=n" patch. There is no
functionality loss because "ide=nodma" kernel option is still available.
Cc: Patrick Horn <phrh@yahoo.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
For CONFIG_IDEDMA_{ICS,PCI}_AUTO=n and/or "ide=nodma" option the host/device
are not programmed for DMA and it is also explicitly disabled by ide_set_dma()
(->ide_dma_check returns "-1"). However the code responsible for manually
enabling DMA ("hdparm -d 1") has a bug which results in DMA being erroneously
enabled - ide_set_dma() incorrectly passes "0" return value to set_using_dma().
This may work if BIOS/firmware configured the host/device for DMA and chipset
allows independent configuration of DMA/PIO modes but won't work after suspend
and is generally unsafe on many chipsets (possibly including data corruption
if the same registers are used for DMA/PIO timings).
This patch fixes kernel bugzilla bug #8169 (piix host driver fixes for
setting PIO mode exposed the problem described above). The side-effect of
the fix is that some rare configuration may be forced to PIO mode when DMA
mode was previously used - this is addressed by the next patch which removes
CONFIG_IDEDMA_{PCI,ICS}_AUTO config option completely.
Thanks goes out to Patrick Horn for reporting the issue, narrowing it down
to the specific commit and testing the fix. Also thanks to Sergei Shtylyov
for help in debugging the problem.
Cc: Patrick Horn <phrh@yahoo.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch fixes:
* the dependency of scc_pata on BLK_DEV_IDEDMA_PCI
* incorrect link to ide-core
* move scc_pata from ide/ppc to ide/pci
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Al Viro <viro@ftp.linux.org.uk>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
When libata is configured, the device is configured such that SATA and
PATA ports live in separate functions with different programming
interfaces. pata_jmicron and ide jmicron drivers can drive only the
PATA part.
This patch makes jmicron match PCI class code such that it doesn't
attach itself to the SATA part preventing the proper ahci driver from
attaching.
This change is suggested by Bartlomiej.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: justin@jmicron.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver wrongly takes the address setup time into account when calculating
the PIO recovery time -- this leads to slight overclocking of the PIO modes 0
and 1 (so, the prayers failed to help, as usual :-). Rework the code to be
calculating recovery clock count as a difference between the total cycle count
and the active count (we don't need to calculate the recovery time itself since
it's not specified for the PIO modes 0 to 2, and for modes 3 and 4 this formula
gives enough recovery time anyway in the chip's supported PCI frequency range).
This patch has been inspired by reading the datasheets and looking at what the
libata driver does; it has been compile-tested only (as usual :-) but anyway,
the new code gives the same or longer recovery times than the old one...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It's bool and it depends on IDE => should depend on IDE=y
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Legacy IDE VLB host drivers didn't check for "probe" options when compiled
as modules, which was obviously wrong as we don't want module to poke at
random I/O ports by simply loading it. Fix it by adding "probe" module param
to legacy IDE VLB host drivers.
v2:
* don't obsolete old "ide0=dtc2278/ht6560b/qd65xx/ali14xx/umc8672"
IDE driver options yet (per Alan Cox's request) and enhance documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove
* "hdx=serialize"
* "idex=noautotune"
* "idex=autotune"
kernel params, they have been obsoleted for ages.
"idex=serialize", "hdx=noautotune" and "hdx=autotune" are still available
so there is no funcionality loss caused by this patch.
v2:
* fix CONFIG_BLK_DEV_4DRIVES=y build broken by version 1 of the patch
[ /me wearing brown paper bag ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 27 February 2007, Akira Iguchi wrote:
>
> But since I sent the first patch, I found a bug for checking DMA IRQ status.
> (http://www.spinics.net/lists/linux-ide/msg06903.html)
> Then I sent the fixed patch for libata only. So my drivers/ide patch
> still has same bug and I want to fix it, too.
>
> The following patch fixes this bug. Please apply this patch.
From: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Revised DRAC4 warning as Jeff suggested, this one includes more info
about why the problem occurs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix breakage added in the IDE devel tree.
Add header, then fix
drivers/ide/ppc/pmac.c: In function `pmac_ide_setup_dma':
drivers/ide/ppc/pmac.c:2044: warning: assignment from incompatible pointer type
drivers/ide/ppc/pmac.c: In function `pmac_ide_dma_host_on':
drivers/ide/ppc/pmac.c:1989: warning: control reaches end of non-void function
include/linux/pci.h: In function `pmac_ide_init':
drivers/ide/ppc/pmac.c:1563: warning: ignoring return value of `pci_register_driver', declared with attribute warn_unused_result
Then add some apparently-long-missing error handling.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add CFA devices from I-O Data, Mitsubishi and Viking. Add SanDisk comment.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The tuneproc() method in both these drivers failed to set the drive's own speed.
Fix this by renaming the function and "wrapping around it" the new tuneproc()
method. Switch back to calling tuneproc() in the PIO fallback code.
While at it, also convert the rest of the PIO timing code into proper C. :-)
Has been kind of tested on SLC90E66. I'm too lazy to reboot my box and test
on ICH4... :-)
[ bart: I quickly tested it on ICH4. ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
eighty_ninty_three() had word 93 validitity check but not the 80c bit
test itself (bit 13). This increases the chance of incorrect wire
detection especially because host side cable detection is often
unreliable and we sometimes soley depend on drive side cable
detection. Fix it.
[ bart: fix off-by-1 bit name in the patch description ]
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to cmd64x_tune_pio(), making it return the mode set,
and "wrapping" the new tuneproc() method around it; while at it, also get rid
of the non-working prefetch control code (filtering out related argument values
in the "wrapper"), remove redundant PIO5 mode limitation, make cmdprintk() give
more sensible mode info, and remove mention about the obsolete /proc/ interface.
Get rid of the broken config_chipset_for_pio() which always tried to set PIO4,
switch to always auto-tuning PIO instead.
Oh, and add the missing PIO5 support to the speedproc() method while at it. :-)
Warning: compile tested only -- getting to the real hardware isn't that easy...
On Tuesday 06 February 2007 22:11, Mikael Pettersson <mikpe@it.uu.se> wrote:
>
> Worked fine on my SPARC Ultra5 with a CMD646 IDE controller.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to ali15x3_tune_pio() and "wrapping" the new tuneproc()
method around it and making it return the mode set, update the heading comment.
Also, setting PIO mode via the speedproc() method does not work due to passing
to the tuneproc() method's a mode number not biased by XFER_PIO_0 -- fix this
along with a typo in the heading comment...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_host_on is called either when drive->using_dma == 1
or when return value is discarded make it void, also drop "ide_" prefix
* make __ide_dma_host_on() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_on() to atiixp_dma_host_on()
and sgiioc4_ide_dma_host_on() to sgiioc4_dma_host_on().
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All users of ->mmio == 1 are gone so convert ->mmio into flag.
Noticed by Alan Cox.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly
Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).
v2:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove bogus comment for sis5513_config_xfer_rate()
* there is no need to call config_drive_art_rwp() because
it is called by config_art_rwp_pio()
* remove needless wrapper
* remove stale "TODO" comment
(IDE core should provide generic tuning code)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* disable DMA masks if no_piix_dma is set and remove now
not needed no_piix_dma_check from piix_config_drive_for_dma()
* there is no need to read register 0x55 in init_hwif_piix()
* move cable detection code to piix_cable_detect()
* remove unreachable 82371MX code from init_hwif_piix()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove redundant svwks_ide_dma_end() [ __ide_dma_end() is used by default ]
* remove init_dma_svwks() so the default ide_setup_dma() function is used
[ init_setup_csb6() takes care of not initializing disabled channels ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* BUG() on unknown DMA mode in cs5530_config_dma()
* there is no need to call hwif->ide_dma_host_{off,on}() in
cs5530_config_dma() because hwif->ide_dma_host_{off,on}()
is called by hwif->ide_dma_off_{quietly,on}()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz