SLAB_LEVEL_MASK is only used internally to the slab and is
and alias of GFP_LEVEL_MASK.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is only used internally in the slab.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Binderman and his Intel C compiler rightly observe that
install_file_pte no longer has any use for its pte_val.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: d binderman <dcb314@hotmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These patches introduced new switch statements which are indented contrary
to the concensus in mm/*.c. Fix them up to match that concensus.
[PATCH] node local per-cpu-pages
[PATCH] ZVC: Scale thresholds depending on the size of the system
commit e7c8d5c995
commit df9ecaba3f
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fsfuzzer found this; with a corrupt small swapfile that claims to have
many pages:
[root]# file swap.741.img
swap.741.img: Linux/i386 swap file (new style) 1 (4K pages) size 1040191487 pages
[root]# ls -l swap.741.img
-rw-r--r-- 1 root root 16777216 Nov 22 05:18 swap.741.img
sys_swapon() will try to vmalloc all those pages, and -then- check to see if
the file is actually that large:
if (!(p->swap_map = vmalloc(maxpages * sizeof(short)))) {
<snip>
if (swapfilesize && maxpages > swapfilesize) {
printk(KERN_WARNING
"Swap area shorter than signature indicates\n");
It seems to me that it would make more sense to move this test up before
the vmalloc, with the other checks, to avoid the OOM-killer in this
situation...
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NUMA node ids are passed as either int or unsigned int almost exclusivly
page_to_nid and zone_to_nid both return unsigned long. This is a throw
back to when page_to_nid was a #define and was thus exposing the real type
of the page flags field.
In addition to fixing up the definitions of page_to_nid and zone_to_nid I
audited the users of these functions identifying the following incorrect
uses:
1) mm/page_alloc.c show_node() -- printk dumping the node id,
2) include/asm-ia64/pgalloc.h pgtable_quicklist_free() -- comparison
against numa_node_id() which returns an int from cpu_to_node(), and
3) mm/mpolicy.c check_pte_range -- used as an index in node_isset which
uses bit_set which in generic code takes an int.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drain_node_pages() currently drains the complete pageset of all pages. If
there are a large number of pages in the queues then we may hold off
interrupts for too long.
Duplicate the method used in free_hot_cold_page. Only drain pcp->batch
pages at one time.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the needlessly global "global_faults" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When booting a NUMA system with nodes that have no memory (eg by limiting
memory), bootmem_alloc_core tried to find pages in an uninitialized
bootmem_map. This caused a null pointer access. This fix adds a check, so
that NULL is returned. That will enable the caller (bootmem_alloc_nopanic)
to alloc memory on other without a panic.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Martin Bligh <mbligh@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch (as824b) makes percpu_free() ignore NULL arguments, as one would
expect for a deallocation routine. (Note that free_percpu is #defined as
percpu_free in include/linux/percpu.h.) A few callers are updated to remove
now-unneeded tests for NULL. A few other callers already seem to assume
that passing a NULL pointer to percpu_free() is okay!
The patch also removes an unnecessary NULL check in percpu_depopulate().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We have variants of kmalloc and kmem_cache_alloc that leave leak tracking to
the caller. This is used for subsystem-specific allocators like skb_alloc.
To make skb_alloc node-aware we need similar routines for the node-aware slab
allocator, which this patch adds.
Note that the code is rather ugly, but it mirrors the non-node-aware code 1:1:
[akpm@osdl.org: add module export]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It would be possible for /proc/swaps to not always print out the header:
swapon /dev/hdc2
swapon /dev/hde2
swapoff /dev/hdc2
At this point /proc/swaps would not have a header.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
OOM can panic due to the processes stuck in __alloc_pages() doing infinite
rebalance loop while no memory can be reclaimed. OOM killer tries to kill
some processes, but unfortunetaly, rebalance label was moved by someone
below the TIF_MEMDIE check, so buddy allocator doesn't see that process is
OOM-killed and it can simply fail the allocation :/
Observed in reality on RHEL4(2.6.9)+OpenVZ kernel when a user doing some
memory allocation tricks triggered OOM panic.
Signed-off-by: Denis Lunev <den@sw.ru>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mm is defined as vma->vm_mm, so use that.
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When using numa=fake on non-NUMA hardware there is no benefit to having the
alien caches, and they consume much memory.
Add a kernel boot option to disable them.
Christoph sayeth "This is good to have even on large NUMA. The problem is
that the alien caches grow by the square of the size of the system in terms of
nodes."
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's an attempt towards doing away with lock_cpu_hotplug in the slab
subsystem. This approach also fixes a bug which shows up when cpus are
being offlined/onlined and slab caches are being tuned simultaneously.
http://marc.theaimsgroup.com/?l=linux-kernel&m=116098888100481&w=2
The patch has been stress tested overnight on a 2 socket 4 core AMD box with
repeated cpu online and offline, while dbench and kernbench process are
running, and slab caches being tuned at the same time.
There were no lockdep warnings either. (This test on 2,6.18 as 2.6.19-rc
crashes at __drain_pages
http://marc.theaimsgroup.com/?l=linux-kernel&m=116172164217678&w=2 )
The approach here is to hold cache_chain_mutex from CPU_UP_PREPARE until
CPU_ONLINE (similar in approach as worqueue_mutex) . Slab code sensitive
to cpu_online_map (kmem_cache_create, kmem_cache_destroy, slabinfo_write,
__cache_shrink) is already serialized with cache_chain_mutex. (This patch
lengthens cache_chain_mutex hold time at kmem_cache_destroy to cover this).
This patch also takes the cache_chain_sem at kmem_cache_shrink to protect
sanity of cpu_online_map at __cache_shrink, as viewed by slab.
(kmem_cache_shrink->__cache_shrink->drain_cpu_caches). But, really,
kmem_cache_shrink is used at just one place in the acpi subsystem! Do we
really need to keep kmem_cache_shrink at all?
Another note. Looks like a cpu hotplug event can send CPU_UP_CANCELED to
a registered subsystem even if the subsystem did not receive CPU_UP_PREPARE.
This could be due to a subsystem registered for notification earlier than
the current subsystem crapping out with NOTIFY_BAD. Badness can occur with
in the CPU_UP_CANCELED code path at slab if this happens (The same would
apply for workqueue.c as well). To overcome this, we might have to use either
a) a per subsystem flag and avoid handling of CPU_UP_CANCELED, or
b) Use a special notifier events like LOCK_ACQUIRE/RELEASE as Gautham was
using in his experiments, or
c) Do not send CPU_UP_CANCELED to a subsystem which did not receive
CPU_UP_PREPARE.
I would prefer c).
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When CONFIG_SLAB_DEBUG is used in combination with ARCH_SLAB_MINALIGN, some
debug flags should be disabled which depend on BYTES_PER_WORD alignment.
The disabling of these debug flags is not properly handled when
BYTES_PER_WORD < ARCH_SLAB_MEMALIGN < cache_line_size()
This patch fixes that and also adds an alignment check to
cache_alloc_debugcheck_after() when ARCH_SLAB_MINALIGN is used.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Imprecise RSS accounting is an irritating ill effect with pt sharing. After
consulted with several VM experts, I have tried various methods to solve that
problem: (1) iterate through all mm_structs that share the PT and increment
count; (2) keep RSS count in page table structure and then sum them up at
reporting time. None of the above methods yield any satisfactory
implementation.
Since process RSS accounting is pure information only, I propose we don't
count them at all for hugetlb page. rlimit has such field, though there is
absolutely no enforcement on limiting that resource. One other method is to
account all RSS at hugetlb mmap time regardless they are faulted or not. I
opt for the simplicity of no accounting at all.
Hugetlb page are special, they are reserved up front in global reservation
pool and is not reclaimable. From physical memory resource point of view, it
is already consumed regardless whether there are users using them.
If the concern is that RSS can be used to control resource allocation, we
already can specify hugetlb fs size limit and sysadmin can enforce that at
mount time. Combined with the two points mentioned above, I fail to see if
there is anything got affected because of this patch.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Dave McCracken <dmccr@us.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Following up with the work on shared page table done by Dave McCracken. This
set of patch target shared page table for hugetlb memory only.
The shared page table is particular useful in the situation of large number of
independent processes sharing large shared memory segments. In the normal
page case, the amount of memory saved from process' page table is quite
significant. For hugetlb, the saving on page table memory is not the primary
objective (as hugetlb itself already cuts down page table overhead
significantly), instead, the purpose of using shared page table on hugetlb is
to allow faster TLB refill and smaller cache pollution upon TLB miss.
With PT sharing, pte entries are shared among hundreds of processes, the cache
consumption used by all the page table is smaller and in return, application
gets much higher cache hit ratio. One other effect is that cache hit ratio
with hardware page walker hitting on pte in cache will be higher and this
helps to reduce tlb miss latency. These two effects contribute to higher
application performance.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Dave McCracken <dmccr@us.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an arch_alloc_page to match arch_free_page.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new swap token patches replace the current token traversal algo. The old
algo had a crude timeout parameter that was used to handover the token from
one task to another. This algo, transfers the token to the tasks that are in
need of the token. The urgency for the token is based on the number of times
a task is required to swap-in pages. Accordingly, the priority of a task is
incremented if it has been badly affected due to swap-outs. To ensure that
the token doesnt bounce around rapidly, the token holders are given a priority
boost. The priority of tasks is also decremented, if their rate of swap-in's
keeps reducing. This way, the condition to check whether to pre-empt the swap
token, is a matter of comparing two task's priority fields.
[akpm@osdl.org: cleanups]
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@celunite.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure the contention for the token happens _before_ any read-in and
kicks the swap-token algo only when the VM is under pressure.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@celunite.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't cause all threads in all other thread groups to gain TIF_MEMDIE
otherwise we'll get a thundering herd eating our memory reserve. This may not
be the optimal scheme, but it fits our policy of allowing just one TIF_MEMDIE
in the system at once.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the OOM killer messages to be more consistent.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abort the kill if any of our threads have OOM_DISABLE set. Having this
test here also prevents any OOM_DISABLE child of the "selected" process
from being killed.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Optimize the critical zonelist scanning for free pages in the kernel memory
allocator by caching the zones that were found to be full recently, and
skipping them.
Remembers the zones in a zonelist that were short of free memory in the
last second. And it stashes a zone-to-node table in the zonelist struct,
to optimize that conversion (minimize its cache footprint.)
Recent changes:
This differs in a significant way from a similar patch that I
posted a week ago. Now, instead of having a nodemask_t of
recently full nodes, I have a bitmask of recently full zones.
This solves a problem that last weeks patch had, which on
systems with multiple zones per node (such as DMA zone) would
take seeing any of these zones full as meaning that all zones
on that node were full.
Also I changed names - from "zonelist faster" to "zonelist cache",
as that seemed to better convey what we're doing here - caching
some of the key zonelist state (for faster access.)
See below for some performance benchmark results. After all that
discussion with David on why I didn't need them, I went and got
some ;). I wanted to verify that I had not hurt the normal case
of memory allocation noticeably. At least for my one little
microbenchmark, I found (1) the normal case wasn't affected, and
(2) workloads that forced scanning across multiple nodes for
memory improved up to 10% fewer System CPU cycles and lower
elapsed clock time ('sys' and 'real'). Good. See details, below.
I didn't have the logic in get_page_from_freelist() for various
full nodes and zone reclaim failures correct. That should be
fixed up now - notice the new goto labels zonelist_scan,
this_zone_full, and try_next_zone, in get_page_from_freelist().
There are two reasons I persued this alternative, over some earlier
proposals that would have focused on optimizing the fake numa
emulation case by caching the last useful zone:
1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems)
have seen real customer loads where the cost to scan the zonelist
was a problem, due to many nodes being full of memory before
we got to a node we could use. Or at least, I think we have.
This was related to me by another engineer, based on experiences
from some time past. So this is not guaranteed. Most likely, though.
The following approach should help such real numa systems just as
much as it helps fake numa systems, or any combination thereof.
2) The effort to distinguish fake from real numa, using node_distance,
so that we could cache a fake numa node and optimize choosing
it over equivalent distance fake nodes, while continuing to
properly scan all real nodes in distance order, was going to
require a nasty blob of zonelist and node distance munging.
The following approach has no new dependency on node distances or
zone sorting.
See comment in the patch below for a description of what it actually does.
Technical details of note (or controversy):
- See the use of "zlc_active" and "did_zlc_setup" below, to delay
adding any work for this new mechanism until we've looked at the
first zone in zonelist. I figured the odds of the first zone
having the memory we needed were high enough that we should just
look there, first, then get fancy only if we need to keep looking.
- Some odd hackery was needed to add items to struct zonelist, while
not tripping up the custom zonelists built by the mm/mempolicy.c
code for MPOL_BIND. My usual wordy comments below explain this.
Search for "MPOL_BIND".
- Some per-node data in the struct zonelist is now modified frequently,
with no locking. Multiple CPU cores on a node could hit and mangle
this data. The theory is that this is just performance hint data,
and the memory allocator will work just fine despite any such mangling.
The fields at risk are the struct 'zonelist_cache' fields 'fullzones'
(a bitmask) and 'last_full_zap' (unsigned long jiffies). It should
all be self correcting after at most a one second delay.
- This still does a linear scan of the same lengths as before. All
I've optimized is making the scan faster, not algorithmically
shorter. It is now able to scan a compact array of 'unsigned
short' in the case of many full nodes, so one cache line should
cover quite a few nodes, rather than each node hitting another
one or two new and distinct cache lines.
- If both Andi and Nick don't find this too complicated, I will be
(pleasantly) flabbergasted.
- I removed the comment claiming we only use one cachline's worth of
zonelist. We seem, at least in the fake numa case, to have put the
lie to that claim.
- I pay no attention to the various watermarks and such in this performance
hint. A node could be marked full for one watermark, and then skipped
over when searching for a page using a different watermark. I think
that's actually quite ok, as it will tend to slightly increase the
spreading of memory over other nodes, away from a memory stressed node.
===============
Performance - some benchmark results and analysis:
This benchmark runs a memory hog program that uses multiple
threads to touch alot of memory as quickly as it can.
Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of
the total 96 GBytes on the system, and using 1, 19, 37, or 55
threads (on a 56 CPU system.) System, user and real (elapsed)
timings were recorded for each run, shown in units of seconds,
in the table below.
Two kernels were tested - 2.6.18-mm3 and the same kernel with
this zonelist caching patch added. The table also shows the
percentage improvement the zonelist caching sys time is over
(lower than) the stock *-mm kernel.
number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent
GBs N ------------ -------------- ---------------- systime
mem threads sys user real sys user real sys user real better
12 1 153 24 177 151 24 176 -2 0 -1 1%
12 19 99 22 8 99 22 8 0 0 0 0%
12 37 111 25 6 112 25 6 1 0 0 -0%
12 55 115 25 5 110 23 5 -5 -2 0 4%
38 1 502 74 576 497 73 570 -5 -1 -6 0%
38 19 426 78 48 373 76 39 -53 -2 -9 12%
38 37 544 83 36 547 82 36 3 -1 0 -0%
38 55 501 77 23 511 80 24 10 3 1 -1%
64 1 917 125 1042 890 124 1014 -27 -1 -28 2%
64 19 1118 138 119 965 141 103 -153 3 -16 13%
64 37 1202 151 94 1136 150 81 -66 -1 -13 5%
64 55 1118 141 61 1072 140 58 -46 -1 -3 4%
90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4%
90 19 2392 199 192 2116 189 176 -276 -10 -16 11%
90 37 3313 238 175 2972 225 145 -341 -13 -30 10%
90 55 1948 210 104 1843 213 100 -105 3 -4 5%
Notes:
1) This test ran a memory hog program that started a specified number N of
threads, and had each thread allocate and touch 1/N'th of
the total memory to be used in the test run in a single loop,
writing a constant word to memory, one store every 4096 bytes.
Watching this test during some earlier trial runs, I would see
each of these threads sit down on one CPU and stay there, for
the remainder of the pass, a different CPU for each thread.
2) The 'real' column is not comparable to the 'sys' or 'user' columns.
The 'real' column is seconds wall clock time elapsed, from beginning
to end of that test pass. The 'sys' and 'user' columns are total
CPU seconds spent on that test pass. For a 19 thread test run,
for example, the sum of 'sys' and 'user' could be up to 19 times the
number of 'real' elapsed wall clock seconds.
3) Tests were run on a fresh, single-user boot, to minimize the amount
of memory already in use at the start of the test, and to minimize
the amount of background activity that might interfere.
4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM.
5) Notice that the 'real' time gets large for the single thread runs, even
though the measured 'sys' and 'user' times are modest. I'm not sure what
that means - probably something to do with it being slow for one thread to
be accessing memory along ways away. Perhaps the fake numa system, running
ostensibly the same workload, would not show this substantial degradation
of 'real' time for one thread on many nodes -- lets hope not.
6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs)
ran quite efficiently, as one might expect. Each pair of threads needed
to allocate and touch the memory on the node the two threads shared, a
pleasantly parallizable workload.
7) The intermediate thread count passes, when asking for alot of memory forcing
them to go to a few neighboring nodes, improved the most with this zonelist
caching patch.
Conclusions:
* This zonelist cache patch probably makes little difference one way or the
other for most workloads on real numa hardware, if those workloads avoid
heavy off node allocations.
* For memory intensive workloads requiring substantial off-node allocations
on real numa hardware, this patch improves both kernel and elapsed timings
up to ten per-cent.
* For fake numa systems, I'm optimistic, but will have to leave that up to
Rohit Seth to actually test (once I get him a 2.6.18 backport.)
Signed-off-by: Paul Jackson <pj@sgi.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: David Rientjes <rientjes@cs.washington.edu>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The zone table is mostly not needed. If we have a node in the page flags
then we can get to the zone via NODE_DATA() which is much more likely to be
already in the cpu cache.
In case of SMP and UP NODE_DATA() is a constant pointer which allows us to
access an exact replica of zonetable in the node_zones field. In all of
the above cases there will be no need at all for the zone table.
The only remaining case is if in a NUMA system the node numbers do not fit
into the page flags. In that case we make sparse generate a table that
maps sections to nodes and use that table to to figure out the node number.
This table is sized to fit in a single cache line for the known 32 bit
NUMA platform which makes it very likely that the information can be
obtained without a cache miss.
For sparsemem the zone table seems to be have been fairly large based on
the maximum possible number of sections and the number of zones per node.
There is some memory saving by removing zone_table. The main benefit is to
reduce the cache foootprint of the VM from the frequent lookups of zones.
Plus it simplifies the page allocator.
[akpm@osdl.org: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- s/freeliest/freelist/ spelling fix
- Check for NULL *z zone seems useless - even if it could happen, so
what? Perhaps we should have a check later on if we are faced with an
allocation request that is not allowed to fail - shouldn't that be a
serious kernel error, passing an empty zonelist with a mandate to not
fail?
- Initializing 'z' to zonelist->zones can wait until after the first
get_page_from_freelist() fails; we only use 'z' in the wakeup_kswapd()
loop, so let's initialize 'z' there, in a 'for' loop. Seems clearer.
- Remove superfluous braces around a break
- Fix a couple errant spaces
- Adjust indentation on the cpuset_zone_allowed() check, to match the
lines just before it -- seems easier to read in this case.
- Add another set of braces to the zone_watermark_ok logic
From: Paul Jackson <pj@sgi.com>
Backout one item from a previous "memory page_alloc minor cleanups" patch.
Until and unless we are certain that no one can ever pass an empty zonelist
to __alloc_pages(), this check for an empty zonelist (or some BUG
equivalent) is essential. The code in get_page_from_freelist() blow ups if
passed an empty zonelist.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was playing with blackfin when i hit a neat bug ... doing an open() on a
directory and then passing that fd to mmap() would cause the kernel to hang
after poking into the code a bit more, i found that
mm/nommu.c:validate_mmap_request() checks the length and if it is 0, just
returns the address ... this is in stark contrast to mmu's
mm/mmap.c:do_mmap_pgoff() where it returns -EINVAL for 0 length requests ...
i then noticed that some other parts of the logic is out of date between the
two funcs, so perhaps that's the easy fix ?
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
find_min_pfn_for_node() and find_min_pfn_with_active_regions() both
depend on a sorted early_node_map[]. However, sort_node_map() is being
called after fin_min_pfn_with_active_regions() in
free_area_init_nodes().
In most cases, this is ok, but on at least one x86_64, the SRAT table
caused the E820 ranges to be registered out of order. This gave the
wrong values for the min PFN range resulting in some pages not being
initialised.
This patch sorts the early_node_map in find_min_pfn_for_node(). It has
been boot tested on x86, x86_64, ppc64 and ia64.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
Separate delayable work items from non-delayable work items be splitting them
into a separate structure (delayed_work), which incorporates a work_struct and
the timer_list removed from work_struct.
The work_struct struct is huge, and this limits it's usefulness. On a 64-bit
architecture it's nearly 100 bytes in size. This reduces that by half for the
non-delayable type of event.
Signed-Off-By: David Howells <dhowells@redhat.com>
Recently, __get_vm_area_node() was changed like following
if (unlikely(!area))
return NULL;
- if (unlikely(!size)) {
- kfree (area);
+ if (unlikely(!size))
return NULL;
- }
It is leaking `area', also original code seems strange already.
Probably, we wanted to do this patch.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit cb07c9a186 causes the wrong return
value. is_hugepage_only_range() is a boolean, so we should return
-EINVAL rather than 1.
Also - we can use "mm" instead of looking up "current->mm" again.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unlike mmap(), the codepath for brk() creates a vma without first checking
that it doesn't touch a region exclusively reserved for hugepages. On
powerpc, this can allow it to create a normal page vma in a hugepage
region, causing oopses and other badness.
Add a test to prevent this. With this patch, brk() will simply fail if it
attempts to move the break into a hugepage reserved region.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(David:)
If hugetlbfs_file_mmap() returns a failure to do_mmap_pgoff() - for example,
because the given file offset is not hugepage aligned - then do_mmap_pgoff
will go to the unmap_and_free_vma backout path.
But at this stage the vma hasn't been marked as hugepage, and the backout path
will call unmap_region() on it. That will eventually call down to the
non-hugepage version of unmap_page_range(). On ppc64, at least, that will
cause serious problems if there are any existing hugepage pagetable entries in
the vicinity - for example if there are any other hugepage mappings under the
same PUD. unmap_page_range() will trigger a bad_pud() on the hugepage pud
entries. I suspect this will also cause bad problems on ia64, though I don't
have a machine to test it on.
(Hugh:)
prepare_hugepage_range() should check file offset alignment when it checks
virtual address and length, to stop MAP_FIXED with a bad huge offset from
unmapping before it fails further down. PowerPC should apply the same
prepare_hugepage_range alignment checks as ia64 and all the others do.
Then none of the alignment checks in hugetlbfs_file_mmap are required (nor
is the check for too small a mapping); but even so, move up setting of
VM_HUGETLB and add a comment to warn of what David Gibson discovered - if
hugetlbfs_file_mmap fails before setting it, do_mmap_pgoff's unmap_region
when unwinding from error will go the non-huge way, which may cause bad
behaviour on architectures (powerpc and ia64) which segregate their huge
mappings into a separate region of the address space.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Adam Litke <agl@us.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- reorder 'struct vm_struct' to speedup lookups on CPUS with small cache
lines. The fields 'next,addr,size' should be now in the same cache line,
to speedup lookups.
- One minor cleanup in __get_vm_area_node()
- Bugfixes in vmalloc_user() and vmalloc_32_user() NULL returns from
__vmalloc() and __find_vm_area() were not tested.
[akpm@osdl.org: remove redundant BUG_ONs]
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_move_pages() uses vmalloc() to allocate an array of structures that is
fills with information passed from user mode and then passes to
do_stat_pages() (in the case the node list is NULL). do_stat_pages()
depends on a marker in the node field of the structure to decide how large
the array is and this marker is correctly inserted into the last element of
the array. However, vmalloc() doesn't zero the memory it allocates and if
the user passes NULL for the node list, then the node fields are not filled
in (except for the end marker). If the memory the vmalloc() returned
happend to have a word with the marker value in it in just the right place,
do_pages_stat will fail to fill the status field of part of the array and
we will return (random) kernel data to user mode.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like there is a bug in init_reap_node() in slab.c that can cause
multiple oops's on certain ES7000 configurations. The variable reap_node
is defined per cpu, but only initialized on a single CPU. This causes an
oops in next_reap_node() when __get_cpu_var(reap_node) returns the wrong
value. Fix is below.
Signed-off-by: Dan Yeisley <dan.yeisley@unisys.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Christoph Lameter <clameter@engr.sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current read_pages() assume ->readpages() frees the passed pages.
This patch free the pages in ->read_pages(), if those were remaining in the
pages_list. So, readpages() just can ignore the remaining pages in
pages_list.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Un-needed add-store operation wastes a few bytes.
8 bytes wasted with -O2, on a ppc.
Signed-off-by: nkalmala <nkalmala@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As reported by Martin J. Bligh <mbligh@google.com>, we let through some
non-slab bits to slab allocation through __get_vm_area_node when doing a
vmalloc.
I haven't been able to reproduce this, although I understand why it
happens: vmalloc allocates memory with
GFP_KERNEL | __GFP_HIGHMEM
and commit 52fd24ca1d resulted in the same
flags are passed down to cache_alloc_refill, causing the BUG. The
following patch fixes it.
Note that when calling kmalloc_node, I am masking off __GFP_HIGHMEM with
GFP_LEVEL_MASK, whereas __vmalloc_area_node does the same with
~(__GFP_HIGHMEM | __GFP_ZERO).
IMHO, using GFP_LEVEL_MASK is preferable, but either should fix this
problem.
Signed-off-by: Giridhar Pemmasani (pgiri@yahoo.com)
Cc: Martin J. Bligh <mbligh@google.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
absent_pages_in_range() made the assumption that users of the
arch-independent zone-sizing API would not care about holes beyound the end
of physical memory. This was not the case and was "fixed" in a patch
called "Account for holes that are outside the range of physical memory".
However, when given a range that started before a hole in "real" memory and
ended beyond the end of memory, it would get the result wrong. The bug is
in mainline but a patch is below.
It has been tested successfully on a number of machines and architectures.
Additional credit to Keith Mannthey for discovering the problem, helping
identify the correct fix and confirming it Worked For Him.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: keith mannthey <kmannth@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If you truncated an mmap'ed hugetlbfs file, then faulted on the truncated
area, /proc/meminfo's HugePages_Rsvd wrapped hugely "negative". Reinstate my
preliminary i_size check before attempting to allocate the page (though this
only fixes the most obvious case: more work will be needed here).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Adam Litke <agl@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If __vmalloc is called to allocate memory with GFP_ATOMIC in atomic
context, the chain of calls results in __get_vm_area_node allocating memory
for vm_struct with GFP_KERNEL, causing the 'sleeping from invalid context'
warning. This patch fixes it by passing the gfp flags along so
__get_vm_area_node allocates memory for vm_struct with the same flags.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add __GFP_NOWARN flag to calling of __alloc_pages() in
__kmalloc_section_memmap(). It can reduce noisy failure message.
In ia64, section size is 1 GB, this means that order 8 pages are necessary
for each section's memmap. It is often very hard requirement under heavy
memory pressure as you know. So, __alloc_pages() gives up allocation and
shows many noisy stack traces which means no page for each sections.
(Current my environment shows 32 times of stack trace....)
But, __kmalloc_section_memmap() calls vmalloc() after failure of it, and it
can succeed allocation of memmap. So, its stack trace warning becomes just
noisy. I suppose it shouldn't be shown.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Christoph Lameter