Drive strength for PXA910 is a 2 bit value but because of the mapping in
plat-pxa/mfp.h needs to be shifted up one bit to handle real
location in mfp registers. (MMP2 and PXA910 drive strength start
at bit 11 while PXA168 starts at bit 10).
Values 0, 1, 2, and 3 effectively need to be
0, 2, 4, and 6 to fit into register. 8 does not work.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Drive strength for MMP2 is a 2 bit value but because of the mapping in
plat-pxa/mfp.h needs to be shifted up one bit to handle real
location in mfp registers. (MMP2 and PXA910 drive strength start
at bit 11 while PXA168 starts at bit 10).
Values 0, 1, 2, and 3 effectively need to be
0, 2, 4, and 6 to fit into register. 8 does not work.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: John Watlington <wad@laptop.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Convert mmp to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since CPU_PJ4 is shared between PXA95x and MMP2, select CPU_PJ4 in MMP2
configuration.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
RTC clock will remain at 32KHz and powered on, there is no need for it
at this moment.
Signed-off-by: Jason Chagas <jason.chagas@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Defined I2C/ALARM pin definitions
DS1337 RTC alarm support is tied to RTC_INT_GPIO
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Support for Matrix keypad ESC, ENTER, LEFT, and RIGHT
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Added board defintion, header, and debug UART support.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Reset vector for pxa168 is 0xffff_0000 not 0x0. This fix allows
reboot to work
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Support regulator MAX8649, PMIC MAX8925 into the Jasper.
Backlight & power supply components of MAX8925 are enabled in Jasper.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Sync twsi index to register index. It's used to avoid typo error.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add DMA support in MMP2.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In MMP2, clock tick rate should be 6500000.
Signed-off-by: Mingliang Hu <mhu4@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In mmp2, 6 banks of GPIO registers are supported. So we can support 192
GPIO pins at most.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Enable Tauros2 L2 in mmp2. Tauros2 L2 is shared in Marvell ARM cores.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Use clk_add_table in order to sync with clock driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Support ssp devices in PXA168. PXA168 could reuse the code of PXA SSP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The irq_chip is not yet registered, so no default irq_chip.mask_ack(),
which we have to handle it correctly manually here.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since PMIC INT pin is a special pin of CPU, the status of PMIC INT pin needs
to be cleared after PMIC IRQ occured. Now append the clear operation in
irq chip handler.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Philip Rakity