Use the default partition parser, cmdlinepart, provided by the plat_nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the Synaptics NavPoint touchpad to the hx4700 platform:
1. Change GPIO23_SSP1_SCLK value in hx4700_pin_config[] from an output
to an input, since the NavPoint is connected to SSP in SPI slave mode.
2. Add GPIO102_GPIO (NavPoint power) to hx4700_pin_config[].
3. Add navpoint platform_device to devices[].
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Most PCI implementations perform simple root bus scanning. Rather than
having each group of platforms provide a duplicated bus scan function,
provide the PCI configuration ops structure via the hw_pci structure,
and call the root bus scanning function from core ARM PCI code.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most PCI implementations use the standard PCI swizzle function, which
handles the well defined behaviour of PCI-to-PCI bridges which can be
found on cards (eg, four port ethernet cards.)
Rather than having almost every platform specify the standard swizzle
function, make this the default when no swizzle function is supplied.
Therefore, a swizzle function only needs to be provided when there is
something exceptional which needs to be handled.
This gets rid of the swizzle initializer from 47 files, and leaves us
with just two platforms specifying a swizzle function: ARM Integrator
and Chalice CATS.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the two standard UART signals (GPIO46_STUART_RXD, GPIO47_STUART_TXD) to the
initial mfp config table hx4700_pin_config[] passed to pxa2xx_mfp_config().
Although pxa2xx_transceiver_mode() can subsequently set these two signals via
its own call to pxa2xx_mfp_config(), pxa2xx_transceiver_mode() is only present
when CONFIG_PXA_FICP=y. Hence this patch provides a default mfp config.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This patch is part of a set which adds PCMCIA/CF support for the hx4700.
This patch modifies asic3_gpio_config[] as follows:
1. Remove ASIC3_GPIOC4_CF_nCD, whose purpose is unknown.
2. Add ASIC3_GPIOD4_CF_nCD, the actual CF card detect GPIO.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This patch enables the ASIC3 GPIO (12) as a wakeup source:
1. Set the WAKEUP_ON_EDGE_RISE MFP config bits for GPIO12 in
hx4700_pin_config[].
2. Call gpio_set_wake() for GPIO12.
With GPIO12 thus enabled, the mfd/asic3 driver can enable its own GPIOs
as wakeup sources by implementing a irq_set_wake() handler.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The asic3 driver now sets the DS1WM clock_rate from the newly added
asic3_platform_data clock_rate field.
This patch initializes the asic3_platform_data clock_rate field on the
hx4700 platform.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The Micron MT9M111 camera chip needs its output enable to be
activated in order to work. The bootloader is not required to
activate it, so do it in machine code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The pcm990 baseboard for the pcm027 module used to setup a static
mapping for accessing the CPLD. It became illegal to call iotable_init
that late. The pcm027 support is broken since then. This patch
switches the cpld support to ioremap and removes all references to
previous static mappings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Pins configured as input and have MFP_LPM_DRIVE_* flag set, can have a
wrong output value for some period of time (spike) during the suspend
sequence.
This can happen because the direction of the pins (GPDR) is set by
software and the output level is set by hardware (PGSR) at a later
stage.
Fix the above potential bug by setting the output levels first.
Also save the actual levels of the pins before the suspend and restore
them after the resume, but before the direction settings take place, so
the same bug as described above will not happen in the resume sequence.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Pins that have MFP_LPM_KEEP_OUTPUT set and are configured for output
must retain the output state in low power mode.
Currently, the pin direction configuration is overrided with values
in gpdr_lpm[] array and do not obey the MFP_LPM_KEEP_OUTPUT setting.
Fix the above bug and add some documentation to clarify the
MFP_LPM_KEEP_OUTPUT setting purpose.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
In 3.3, gpio wakeup setting was broken. The call
enable_irq_wake() didn't set up the PXA gpio registers
(PWER, ...) anymore.
Fix it at least for pxa27x. The driver doesn't seem to be
used in pxa25x (weird ...), and the fix doesn't extend to
pxa3xx and pxa95x (which don't have a gpio_set_wake()
available).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
With commit c334bc1 (ARM: make mach/io.h include optional), PCMCIA was
broken. PCMCIA depends on __io() returning a valid i/o address, and most
ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This
needs a better fix with a fixed i/o address mapping, but for now we just
restore things to the previous behavior.
This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled,
but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff,
so it doesn't need an io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This does a sweeping change fixing up all the missing system_misc.h and
system_info.h includes from the system.h split-up change. These were the
ones I came across when building all defconfigs in arch/arm/configs, there
might be more but they lack adequate build coverage to be easily caught.
I'm expecting to get a lot of these piecemeal by each maintainer, so we
might just as well do one sweeping change to get them all at once.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
arch/arm/mach-pxa/stargate2.c:155:3: error: unknown field ‘dev’
specified in initializer
arch/arm/mach-pxa/stargate2.c:155:3: warning: initialization from
incompatible pointer type [enabled by default]
arch/arm/mach-pxa/stargate2.c:155:3: warning: (near initialization for
‘stargate2_sensor_3_con[0].dev_name’) [enabled by default]
make[1]: *** [arch/arm/mach-pxa/stargate2.o] Error 1
make: *** [arch/arm/mach-pxa] Error 2
It's caused by 'dev' field removed from struct
regulator_consumer_supply.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Commit 737f360d5b
"regulator: Remove support for supplies specified by struct device"
caused this file to break, since it was still relying on the
device field to be present. Map it onto dev_name appropriately
Since there are two consumers with the name "reg-userspace-consumer",
we have to supply the ID as a suffix in the REGULATOR_CONSUMER calls.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
commit 737f360d5b (linux-next)
"regulator: Remove support for supplies specified by struct device"
deletes the field from the struct, but this platform was still trying
to set those fields. Delete the assignments.
arch/arm/mach-pxa/magician.c:581: error: unknown field 'dev' specified in initializer
arch/arm/mach-pxa/magician.c:581: warning: initialization from incompatible pointer type
arch/arm/mach-pxa/magician.c:585: error: unknown field 'dev' specified in initializer
arch/arm/mach-pxa/magician.c:585: warning: initialization from incompatible pointer type
arch/arm/mach-pxa/hx4700.c:683: error: unknown field 'dev' specified in initializer
arch/arm/mach-pxa/hx4700.c:683: warning: initialization from incompatible pointer type
arch/arm/mach-pxa/hx4700.c:687: error: unknown field 'dev' specified in initializer
arch/arm/mach-pxa/hx4700.c:687: warning: initialization from incompatible pointer type
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
pxa was missed in the moving of IOMEM to a common definition, so lots of
IOMEM redefined warnings were introduced. So remove pxa IOMEM definition
and fix all the fallout.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: rtc-linux@googlegroups.com
Cc: alsa-devel@alsa-project.org
The only users of ARCH_HAS_DMA_SET_COHERENT_MASK are 2 ARM platforms:
ixp4xx and pxa cm_x2xx. We've been getting lucky that the define is
implicitly included before dma-mapping.h, but the removal of io.h broke
things (c334bc1 ARM: make mach/io.h include optional). Since memory.h
is the correct place, but no longer exists, convert the define to a
kconfig entry.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Some platforms don't want certain devices to be registered, because,
eg, the interface is not wired. Provide a way for platforms to
prevent various devices from being registered via a devid bitmask in
the platform data.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The existing pcmcia platform_device structure is not used and is not needed by
the pending hx4700 PCMCIA/CF support. So let's remove it.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Drive the two Bluetooth UART output GPIOs (GPIO43_BTUART_TXD, GPIO45_BTUART_RTS)
LOW during sleep mode instead of HIGH. This reduces sleep mode battery discharge
from approximately 46 mA to approximately 30 mA.
Signed-off-by: Oliver Winker <oliver@oli1170.net>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
GPIO105 (nIR_ON) is requested twice: first in gpio_request_array(), then in
pxa_irda_probe(). Consequently the second request fails with EBUSY:
pxa2xx-ir: probe of pxa2xx-ir failed with error -16
This patch removes the first request, allowing pxa_irda_probe() to succeed.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Failure is reported on hx4700 with kernel v3.3-rc1.
__mfp_validate: GPIO20 is invalid pin
__mfp_validate: GPIO21 is invalid pin
__mfp_validate: GPIO15 is invalid pin
__mfp_validate: GPIO78 is invalid pin
__mfp_validate: GPIO79 is invalid pin
__mfp_validate: GPIO80 is invalid pin
__mfp_validate: GPIO33 is invalid pin
__mfp_validate: GPIO48 is invalid pin
__mfp_validate: GPIO49 is invalid pin
__mfp_validate: GPIO50 is invalid pin
Since pxa_last_gpio is used in mfp-pxa2xx driver. But it's only
updated in pxa-gpio driver that run after mfp-pxa2xx driver.
So update the pxa_last_gpio first in mfp-pxa2xx driver.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Both reboot (via reboot(RB_AUTOBOOT)) and suspend freeze on hx4700.
Registration of pxa_gpio_syscore_ops is moved into pxa-gpio driver,
but it still exists in arch-pxa directory. It resulsts failure on
reboot and suspend.
Now remove the registration code in arch-pxa.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
This regression was introduced by the commit "ARM: pxa: add dummy
clock for sa1100-rtc", id a55b5adaf4.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
The bq24022 on these machines is a very simple regulator using gpios.
One provides the on/off functionality and a second one is used to
change the current between 100 and 500 mA.
This functionality can also be provided by the more generic gpio-regulator.
Therefore convert both machines which makes it possible to remove the
bq24022 driver later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Add LED support for the HTC ASIC3. Underlying support is provided by the mfd/asic3 and leds/leds-asic3 drivers. An example configuration is provided by the pxa/hx4700 platform.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The HP iPAQ hx4700 has 128Mb of flash provided by two Intel StrataFlash devices.
The hx4700 platform configuration defines a single 128Mb flash resource,
resulting in the MTD physmap-flash driver probing the first device only and
presuming the second device is identical:
physmap platform flash device: 08000000 at 00000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008816
physmap-flash: Found 2 x16 devices at 0x4000000 in 32-bit bank
<snip>
erase region 0: offset=0x0,size=0x10000,blocks=4
erase region 1: offset=0x40000,size=0x40000,blocks=255
erase region 2: offset=0x4000000,size=0x10000,blocks=4
erase region 3: offset=0x4040000,size=0x40000,blocks=255
physmap-flash: 2 set(s) of 2 interleaved chips --> 32 partitions of 4096 KiB
Unfortunately the two devices are not identical. The first has a device ID of
0x8816, identifying a bottom parameter device. The second has a device ID of
0x8813, identifying a top parameter device. By not probing the second device,
physmap-flash does not discover the correct block sizes.
This patch splits the configuration into two 64Mb flash resources, forcing
physmap-flash to probe both devices and thus discover the correct block sizes:
physmap platform flash device: 04000000 at 00000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008816
<snip>
erase region 0: offset=0x0,size=0x10000,blocks=4
erase region 1: offset=0x40000,size=0x40000,blocks=255
physmap-flash: 1 set(s) of 2 interleaved chips --> 16 partitions of 4096 KiB
physmap platform flash device: 04000000 at 04000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008813
<snip>
erase region 0: offset=0x0,size=0x40000,blocks=255
erase region 1: offset=0x3fc0000,size=0x10000,blocks=4
physmap-flash: 1 set(s) of 2 interleaved chips --> 16 partitions of 4096 KiB
Concatenating MTD devices:
(0): "physmap-flash"
(1): "physmap-flash"
into device "physmap-flash"
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
sa1100-rtc driver could be shared among sa1100/pxa/mmp series silicon.
Since clk is used in mmp series silicon, add dummy clock support in
pxa also.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to hard coded irq in rtc-sa1100 driver since we could share
it among arch-sa1100/arch-pxa/arch-mmp.
We still keep hard coded register address since the requirement is
enabling both rtc-sa1100 and rtc-pxa driver. The register addresses
are conflict since they're only two wrappers on the same rtc device.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.
Includes fixes to IMX code from Sascha Hauer.
[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As part of mach/irqs.h include removal from sparse, mainstone.h was missed.
This fixes the compile of the pcmcia driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
The audio on hx4700 needs this to properly work.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
arch/arm/mach-pxa/pxa25x.c and arch/arm/mach-pxa/saarb.c
included 'linux/gpio.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
arch/arm/mach-pxa/pxa27x.c included 'linux/gpio.h' twice, remove
the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
arch/arm/mach-pxa/sharpsl_pm.c: In function
'sharpsl_pm_pxa_read_max1111':
arch/arm/mach-pxa/sharpsl_pm.c:180: warning: ISO C90 forbids mixed
declarations and code
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
(~GPLR0 & GPIO_bit(SPITZ_GPIO_KEY_INT)) | (GPLR0 &
GPIO_bit(SPITZ_GPIO_SYNC));
After using gpio_get_value, the statement should be in below.
((!gpio_get_value(SPITZ_GPIO_KEY_INT)
<< GPIO_bit(SPITZ_GPIO_KEY_INT))
| gpio_get_value(SPITZ_GPIO_SYNC));
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert all the PXA platform socket drivers to use the new irq/gpio
management provided by soc_common. This relieves these drivers from
having to do anything with these GPIOs other than provide the numbers
to soc_common.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
H Hartley Sweeten