The driver needs specific PHY and board support code for each SFC4000
board; there is no point trying to continue if it is missing.
Currently unsupported boards can trigger an 'oops'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by commit
eb9f6744cb "sfc: Implement ethtool
reset operation".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code would wait indefinitely if MAC stats DMA failed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-submitted based on comments from netdev community.
Summary of the changes:
1. Improved error handling.
2. Added the missing timeout arguments to usb_control_msg().
The following is a new Linux driver which exposes certain models of Sierra
Wireless modems to the operating system as Network Interface Cards (NICs).
This driver requires a version of the sierra.c driver which supports
blacklisting to work properly. The blacklist in sierra.c rejects the interfaces
claimed by sierra_net.c. Likewise, the sierra_net.c driver only accepts
(i.e. whitelists) the interface(s) used for USB-to-WWAN traffic.
The version of sierra.c which supports blacklisting is
available from the sierra wireless knowledge base page for older kernels. It is
also available in Linux kernel starting from version 2.6.31.
This driver works with all Sierra Wireless devices configured with PID=68A3
like USB305, USB306 provided the corresponding firmware version is I2.0
(for USB305) or M3.0 (for USB306) and later.
This driver will not work with earlier firmware versions than the ones shown
above. In this case the driver will issue an error message indicating
incompatibility and will not serve the device's USB-to-WWAN interface.
Sierra_net.c sits atop a pre-existing Linux driver called usbnet.c.
A series of hook functions are provided in sierra_net.c which are called by
usbnet.c in response to a particular condition such as receipt or transmission
of a data packet. As such, usbnet.c does most of the work of making
a modem appear to the system as a network device and for properly exchanging
traffic between the USB subsystem and the Network card interface.
Sierra_net.c is concerned with managing the data exchanged between the
USB-to-WWAN interface and the upper layers of the operating system.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Rory Filer <rfiler@sierrawireless.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Autosuspend works until you bring the wwan interface up, then the
device does not enter autosuspend anymore.
The following patch fixes the problem by setting the .manage_power
field in the mbm_info struct to the same as in the cdc_info struct
(cdc_manager_power).
Signed-off-by: Torgny Johansson <torgny.johansson@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped. We need to wait for both, or the
controller could get into an invalid state.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to usb_free_buffer() dereference rx_urb and tx_urb in the
parameter list but those could be NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: L. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91c92_cs:
* spin_unlock_irqrestore before calling smc_interrupt() in media_check()
to avoid lockup.
* use spin_lock_irqsave for ethtool function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver calls ndo_vlan_rx_register() while holding bond->lock.
The bnx2 driver calls bnx2_netif_stop() to stop the rx handling while
changing the vlgrp. The call also stops the cnic driver which sleeps
while the bond->lock is held and cause the warning.
This code path only needs to stop the NAPI rx handling while we are
changing the vlgrp. Since no reset is going to occur, there is no need
to stop cnic in this case. By adding a parameter to bnx2_netif_stop()
to skip stopping cnic, we can avoid the warning.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that under certain heavy traffic conditions in MSI-X
mode, the driver can lose an MSI-X vector causing all packets in the
associated rx/tx ring pair to be dropped. The problem is caused by
the chip dropping the write to unmask the MSI-X vector by the kernel
(when migrating the IRQ for example).
This can be prevented by increasing the GRC timeout value for these
register read and write operations.
Thanks to Dell for helping us debug this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some Power7 platforms, when using VIOS (Virtual I/O Server), we
need to wait longer for control packets to finish transfer during
initialization.
Without this change, initialization may fail prematurely.
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prompted by a previous patch submitted by Matthew Garret <mjg@redhat.com>,
further digging into errata documentation reveals the current enabling or
disabling of ASPM L0s and L1 states for certain parts supported by this
driver are incorrect. 82571 and 82572 should always disable L1. For
standard frames, 82573/82574/82583 can enable L1 but L0s must be disabled,
and for jumbo frames 82573/82574 must disable L1. This allows for some
parts to enable L1 in certain configurations leading to better power
savings.
Also according to the same errata, Early Receive (ERT) should be disabled
on 82573 when using jumbo frames.
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY laser is still on during driver init. It's allowing
garbage to hit our FIFO, which eventually can cause the entire
device to die. Power down the laser while setting up the device,
and re-enable the laser before getting link.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
78f1cd0245 ("fix broken register writes")
does not work for Al Viro's r8169 (XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few (6) network drivers enable mwi explicitly. Fewer worry about a
failure.
It is not a fix but it should avoid some annoyance like
http://bugzilla.kernel.org/show_bug.cgi?id=15454
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Conrad Kostecki <conikost@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Fix INTx fallback when MSI fails
MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.
In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing stops the workqueue being left to run in parallel with close or a
few other operations. This causes double unmaps and the like.
See kerneloops.org #1041230 for an example
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar driver may pass NULL pointer to the of_translate_address(),
which may lead to a kernel oops. Fix this by using of_iomap(), which
is also much simpler and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old P1020RDB device trees were not specifing tbipa address for
MDIO nodes, which is now causing this kernel oops:
...
eth2: TX BD ring size for Q[6]: 256
eth2: TX BD ring size for Q[7]: 256
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0015504
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0015504] memcpy+0x3c/0x9c
LR [c000a9f8] __of_translate_address+0xfc/0x21c
Call Trace:
[df839e00] [c000a94c] __of_translate_address+0x50/0x21c (unreliable)
[df839e50] [c01a33e8] get_gfar_tbipa+0xb0/0xe0
...
The old device trees are buggy, though having a dead ethernet is
better than a dead kernel, so fix the issue by using of_iomap().
Also, a somewhat similar issue exist in the probe() routine, though
there the oops is only a possibility. Nonetheless, fix it too.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new driver to use tethering with an iPhone device. After initial submission,
apply fixes to fit the new driver into the kernel standards.
There are still a couple of minor (almost cosmetic-level) issues, but the driver
is fully functional right now.
Signed-off-by: L. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: Diego Giagio <diego@giagio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I encountered an issue that not to link up on cxgb3 fabric.
I bisected and found that this regression was introduced by
0f07c4ee8c.
Correct to pass phy_addr to cphy_init() at t3_xaui_direct_phy_prep().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL pointer dereference in ks8851_tx_work by checking if dequeued
list is already empty before writing the packet to TX FIFO
Unable to handle kernel NULL pointer dereference at virtual address 00000050
PC is at ks8851_tx_work+0xdc/0x1b0
LR is at wait_for_common+0x148/0x164
pc : [<c01c0df4>] lr : [<c025a980>] psr: 20000013
Backtrace:
ks8851_tx_work+0x0/0x1b0
worker_thread+0x0/0x190
kthread+0x0/0x90
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the stats counter calculation in 3c574_cs, similar
to the method used in 3c589_cs. This corrects the contents
of the counter on tests using a "Megahertz 574B" card.
[linux@dominikbrodowski.net: clean up commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ems_usb_probe(), a pointer is dereferenced after making sure it is NULL...
This patch replaces netdev->dev.parent with &intf->dev in dev_err() calls to
avoid this.
Signed-off-by: "Hans J. Koch" <hjk@linutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_queue is used as a temporary queue when not allowed to queue skb
directly to the hw device driver (which may sleep). Most paths flush
it before returning, but ppp_start() currently cannot. Make sure we
don't leave skbs pointing to a non-existent device.
Thanks to Michael Barkowski for reporting this problem.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.
Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The following situation was observed in the field:
tap1 sends packets, tap2 does not consume them, as a result
tap1 can not be closed. This happens because
tun/tap devices can hang on to skbs undefinitely.
As noted by Herbert, possible solutions include a timeout followed by a
copy/change of ownership of the skb, or always copying/changing
ownership if we're going into a hostile device.
This patch implements the second approach.
Note: one issue still remaining is that since skbs
keep reference to tun socket and tun socket has a
reference to tun device, we won't flush backlog,
instead simply waiting for all skbs to get transmitted.
At least this is not user-triggerable, and
this was not reported in practice, my assumption is
other devices besides tap complete an skb
within finite time after it has been queued.
A possible solution for the second issue
would not to have socket reference the device,
instead, implement dev->destructor for tun, and
wait for all skbs to complete there, but this
needs some thought, probably too risky for 2.6.34.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Yan Vugenfirer <yvugenfi@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for bug 572201 @ bugs.debian.org
This patch fixes the TX_LIMIT feature flag. The previous logic check
for TX_LIMIT2 also took into account a device that only had TX_LIMIT
set.
Reported-by: Stephen Mulcahu <stephen.mulcahy@deri.org>
Reported-by: Ben Huchings <ben@decadent.org.uk>
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91c92_cs:
* define multicast_table as unsigned char
* remove unnecessary "#ifndef final_version"
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx ring buffers after tx_ring->next_to_use are volatile and could
change, possibly causing a crash. Stop cleaning when we hit
tx_ring->next_to_use.
Signed-off-by: Terry Loftin <terry.loftin@hp.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict Wake-on-LAN to first port on 82576 ET2 quad port NICs, as it is
only supported there.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing sg_init_table for sg_set_buf in virtio_net which
induced in defer skb patch.
Reported-by: Thomas Müller <thomas@mathtm.de>
Tested-by: Thomas Müller <thomas@mathtm.de>
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.
The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.
This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rx_pause management in myri10ge_set_pauseparam().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource size should be calculated as end - start + 1 because we start
counting at zero. I changed the code to resource_size() to do the
calculation.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cnic_service_bnx2x() irq handler can be called during chip reset from
MTU change. Need to check that the cnic's device state is up before
handling the irq.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If interface is down, mac address request are not sent to fw
but it is getting add in driver mac list.
Driver mac list should be in sync with fw i.e addresses communicated
to fw.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in <https://bugzilla.kernel.org/show_bug.cgi?id=15355>, r6040_
multicast_list currently crashes. This is due a wrong maximum of multicast
entries. This patch fixes the following issues with multicast:
- number of maximum entries if off-by-one (4 instead of 3)
- the writing of the hash table index is not necessary and leads to invalid
values being written into the MCR1 register, so the MAC is simply put in a non
coherent state
- when we exceed the maximum number of mutlticast address, writing the
broadcast address should be done in registers MID_1{L,M,H} instead of
MID_O{L,M,H}, otherwise we would loose the adapter's MAC address
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
smc91c92_cs:
*cvt_ascii_address returns 0, if success.
*call free_netdev, if we can't find hardware address.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().
To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Henry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Fix formatting on r8169 printk
Brandon Philips noted that I had a spacing issue in my printk for the
last r8169 patch that made it quite ugly. Fix that up and add the PFX
macro to it as well so it looks like the other r8169 printks
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings