This fixes some timings for pre-TBTT and synthetic PU.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows for the correct initial values to be uploaded to bcm4303
devices. It should be correct, but I can't reliably test this as I suspect
there's something going wrong with an hardware rfkill switch on my laptop.
Please test.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the module init message to tell that the legacy
driver loaded. This makes it less confusing, in case both drivers are loaded.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the B43legacy_WARN_ON macro so that it will evaluate expressions.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes uploading of the beacon data and writing of the TIM and DTIM offsets.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some definitions for the MAC control register and uses them. This is
basically no functional change.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds printk messages with basic information about the driver being loaded.
This information includes a summary of the compiled-in features, which
simplifies bug-reporting and debugging a lot.
Also a firmware ID is printed. This is a unique identifier blob for a specific
version of the firmware. This ID is attached to a specific version of the firmware
blob in b43-fwcutter (see fwcutter git).
This helps users to select the right firmware for their device.
This also makes it possible to use automated scripts to fetch and extract the right
firmware for the driver. (The script will grep the .ko for the "Firmware-ID: xxx" string.)
While the driver might still support other versions of the firmware for backward
compatibility, this will always print out the officially supported version, which
people _should_ use.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware version information should always get printed. Not only on a
debug build.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the firmware ID to modinfo.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes suspend/resume work with the b43legacy driver.
We must not overwrite the MAC addresses in the init function, as this
would also overwrite the MAC on resume. With an all-zero MAC the device
firmware is not able to ACK any received packets anymore.
Fix this by moving the initializion stuff that must be done on init but
not on resume to the start function.
Also zero out filter_flags to make sure we don't have some flags
from a previous instance for a tiny timeframe until mac80211 reconfigures
them.
This patch by Michael Buesch has been ported to b43legacy.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This zeros out all microcode related memory before loading
the microcode.
This also fixes initialization of the MAC control register.
The _only_ place where we overwrite the contents of the MAC control
register is at the beginning of b43_chip_init().
All other places must do read() -> mask/set -> write() to not
overwrite existing bits.
This also adds a longer delay for waiting for the microcode
to initialize itself. It seems that the current timeout is sufficient
on all available devices, but there's no real reason why we shouldn't
wait for up to one second. Slow embedded devices might exist.
Better safe than sorry.
While at it, fix naming of MACCTL values.
This patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must kill rfkill in any error paths that trigger after rfkill init.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a sparse warning about weird locking.
The spinlock is not needed, so simply remove it.
This also adds some sanity checks to the PHY and radio locking
to protect against recursive locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes extraction of some values from the SPROM.
It mainly fixes extraction of antenna related values, which
is needed for another b43 fix sent later.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes Bug #9414 for b43legacy. This patch is the equivalent of one
submitted earlier for b43.
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above and removes a couple of sparse warnings.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the hardware on too many PHY TX errors. A thousand PHY TX errors
per 15 seconds means we won't be able to recover for sure.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When monitor mode is enabled, this will make b43legacy read out
the full 64-bit MAC time from the chip for each received packet.
This patch has been ported from b43.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b43legacy driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix my copyright notices in b43 and b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a consistent naming scheme for the ops.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the retry limits provided by mac80211.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need the set_key callback, as we don't do hw crypto.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement much easier and more lightweight locking for
the periodic work. This also removes the last big busywait
loop and replaces it by a sleeping loop.
This patch for b43legacy is patterned aftar the same patch
for b43 by Michael Buesch <mb@bu3sch.de>.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
This patch is the port to b43legacy of a patch for b43 by Michael Buesch
<mb@bu3sch.de>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds full support for the RFKILL button and the RFKILL LED trigger.
This is a port to b43legacy of a patch by Michael Buesch <mb@bu3sch.de>
for b43.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drive the LEDs through the generic LED triggers.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to b43legacy.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the Coverity checker, Adrian Bunk found that routine b43legacy_start
could return an unitialized variable. This patch fixes the problem.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change cleans up the radio-related messages in several ways.
(1) The state of the rfkill switch is assumed to be on, rather than
tested. Now, any user without such a switch will not see any
messages. For devices with such a switch, a message will be
logged only if the initial state is off, or if the switch is toggled.
(2) The routine for testing the switch state is no longer inline.
(3) The LED handling routine is simplified.
(4) The "Radio turned off" message that has confused some users has been
changed to "Radio initialized".
This patch is patterned after a similar change to b43 by Michael Buesch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
This patch is based on a similar patch of b43 by Michael Buesch.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Brivio