Adding the ability to get a physical address from point() in addition
to virtual address. This physical address is required for XIP of
userspace code from flash.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Reviewed-by: Jörn Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
collie seems to contain LH28F640BF flash chips. According to
http://sharp-world.com/products/device/flash/pdf/*FUM00701*@E.pdf
(page 83) if they have 0x51 of Extended Query Table (number of hardware
partitions) set to zero, they have a single fixed partition.
This patch makes those chips work.
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is a known erratum confirmed by Spansion. I have an errata document,
but I can't find a link to it anywhere on their site to include here.
Some of the S29GL064N chips report 64 sectors when they should report 128,
and some of S29GL032N chips report 127 sectors when they should report 63.
Note that when the chip dies are fixed by Spansion, they will still have
the same id. The fix is done in such a way that it won't affect corrected
chips.
The fixups use the extended id made available by a previous patch. Without
that, virtually all newer AMD/Spansion chips will have the same ID (0x227e)
and it's not possible to apply the fixup to the correct chips.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
AMD/Spansion use a device id of 0x7e to indicate an extended device is
present at offset 0xe and 0xf in the query data.
I've verified with Spansion that all their chips (mfr == 0x01) with an id
of 0x7e use it to indicate an extended id is present. What's more, there
are no chips with a NON-extended id that is the same as a different chip's
extended id. In other words, when the extended ID is present, one can
replace the normal id with the extended id without losing any information.
Which is what I've done.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the SST 36VF3203 flash chip. It is used on Emerson
KSI8560 board.
Signed-off-by: Andrei Dolnikov <adolnikov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Untested, but shouldn't break anything... Makes MTD_XIP arch
independent. I guess this is why xip_iprefetch() was made for.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch makes the needlessly global cfi_staa_erase_varsize() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the ST M29W400DB flash chip. which is used on the GLAN Tank
NAS.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
cfi_amdstd_sync() and cfi_staa_sync() call schedule() without changing task's
state appropriately.
In case of e.g. chip->state == FL_ERASING, cfi_*_sync() will be busy-looping
either redundantly for a fixed interval of time (for SCHED_NORMAL tasks) or
possibly endlessly (for RT tasks and UP).
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
THe CFI driver in 2.6.24 kernel is broken. Not so intensive read/write
operations cause incomplete writes which lead to kernel panics in JFFS2.
We investigated the issue - it is caused by bug in FL_SHUTDOWN parsing code.
Sometimes chip returns -EIO as if it is in FL_SHUTDOWN state when it should
wait in FL_PONT (error in order of conditions).
The following patch fixes the bug in state parsing code of CFI. Also I've
added comments to notify developers if they want to add new case in future.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Reviewed-by: Joern Engel <joern@logfs.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=9829
I found and solved the problem, at line 115 of drivers/mtd/chips/gen_probe.c
(kernel 2.6.24): mapsize value must be calculated in bytes, not in long.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch for unlocking all Intel flash that has instant locking on power up.
The patch has been tested on Intel M18, P30 and J3D Strata Flash.
1. The automatic unlocking can be disabled for a particular partition
in the map or the command line.
a. For the bit mask in the map it should look like:
.mask_flags = MTD_POWERUP_LOCK,
b. For the command line parsing it should look like:
mtdparts=0x80000(bootloader)lk
2. This will only unlock parts with instant individual block locking.
Intel parts with legacy unlocking will not be unlocked.
Signed-off-by: Justin Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The bug causes corruptions of data read from flash.
The original code performs cache invalidation from "adr" to "adr + len"
in do_write_buffer(). Since len and adr could be updated in the code
before invalidation - it causes improper setting of cache invalidation
regions.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Signed-off-by: Giuseppe D'Eliseo <giuseppedeliseo@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woohouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to "Common Flash Memory Interface Publication 100" dated December 1,
2001, the interface code for x16/x32 chips is 0x0005, and not 0x0004 used so
far.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use a single unlock address, adjust it for the device type in the
knowledge that it'll be adjusted back again. This has the desirable
effect of masking out the least significant bit of the address for x16
devices.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Having laid the code out so that it's easier to read instead of sticking
to the 80-column guideline even when it doesn't make sense, a bug is
immediately spotted... we were only checking _one_ of the unlock
addresses to see if it runs off the end of the map.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This should have no functional effects -- we've been ignoring all but
the first address in the array for a long time, and using it only to
indicate which device types are supported.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
while running stress tests we have met cfi_cmdset_0001.c driver issue.
Working on multipartitional devices with erase suspend on write
feature enabled it is possible to get erase operation invoked on chip
with suspended erase. get_chip() looses information about earlier
suspended erase and new erase operation gets issued. New erase
operations report successful completion, but blocks remain dirty
causing, for example, JFFS2 error messages like:
...
Newly-erased block contained word 0x20031985 at offset 0x00200000
Newly-erased block contained word 0x20031985 at offset 0x00280000
Newly-erased block contained word 0x20031985 at offset 0x00240000
...
The patch below fixes that issue.
Signed-off-by: Alexander Belyakov <alexander.belyakov@intel.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Convert CFI tables from Atmel cmdset_0001 chips to Intel format and set
BufWrite timeouts to 0 for Atmel cmdset_0001 and cmdset_0002 chips.
Some chips may indicate support for buffered writes even though they
only support dual-word writes.
The CFI fixup must run before fixup_use_write_buffers for this to work.
Signed-off-by: Håvard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch solves kernel deadlock issue seen on JFFF2 simultaneous
operations. Detailed investigation of the issue showed that the kernel
deadlock is caused by tons of recursive get_chip calls.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we press ctrl-alt-del,kernel_restart_prepare will invoke
cfi_intelext_reboot which will set flash to read array mode, but later
when device_shutdown is invoked which may put current work queue to
sleep and other process may be scheduled to running and programming
flash in not FL_READY mode again. So we can't boot up if this flash is
used for bootloader.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The CFI probe routine is capable of detecting flash banks consisting of
identical chips mapped to physically discontiguous addresses. (One
common way this can occur is if a flash bank is populated with chips of
less capacity than the hardware was designed to support.) The CFI
point() routine currently ignores any such gaps. This patch fixes
the CFI point() routine so that it truncates any request that would
span a gap.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch cleans up duplicate includes in
drivers/mtd/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add descriptions for Fujitsu MBM29F800BA and ST M29F800AB flash chips.
Those chips are compatible (except for the ids) with the AMD AM29F800BB.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Trivial fix of a spelling error in a comment in cfi_cmdset_0001.c
s/ships/chips/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use NULL instead of 0 for pointer:
drivers/mtd/chips/cfi_cmdset_0001.c:2258:43: warning: Using plain integer as NULL pointer
Other changes by inspection.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix sparse warnings generated from cfi_cmdset_0001.c.
drivers/mtd/chips/cfi_cmdset_0001.c:1783:5: warning: symbol 'cfi_intelext_erase_varsize' was not declared. Should it be static?
drivers/mtd/chips/cfi_cmdset_0001.c:2258:43: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make cfi_amdstd_erase_varsize static, as declared at the top
of the file to ensure sparse does not print a warning for an
undeclared function, as so:
drivers/mtd/chips/cfi_cmdset_0002.c:1612:5: warning: symbol 'cfi_amdstd_erase_varsize' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is on a custom board with a mapping driver access to an ST
M50LPW080 chip. This chip is probed successfully with
do_map_probe("jedec_probe",...). If I use the mtdchar interface to
perform unlock->erase->program->lock on any of the 16 eraseblocks in the
chip, the chip is left in FL_STATUS mode while the data structures
believe that the chip is in FL_READY mode. Hence, any subsequent reads
to any flash byte results in 0x80 being read.
Signed-off-by: Shashi Rao <shashi@sun.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Auto unlock sectors on resume for auto locking flash on power up.
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The files cfi_cmdset_0002.c and cfi_cmdset_0020.c do not initialize their
wait queues like is done in cfi_cmdset_0001.c. This causes an oops when
the wait queue is accessed. I have copied the code from cfi_cmdset_0001.c
that is pertinent to initialization of the wait queue.
Signed-off-by: Vijay Sampath <vsampath@gmail.com>
Acked-by: Joern Engel <joern@lazybastard.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ugly and weird MTD_PROGREGION_CTRLMODE_VALID() and
MTD_PROGREGION_CTRLMODE_INVALID() macros. There is only one
user of them and they are used locally just for printing.
Anyway, this patch is a preparation for removing mtd->ecctype
and mtd->eccsize, but these macros use them. Fix this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The cfi_staa_write_buffers() uses mtd->eccsize but means mtd->writesize.
BTW, mtd-eccsize is broken and is not initialized, which means the code
fixed by this patch is broken/unused anyway.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In commit c172471b78 Nico switched to using
common code for polling for command completion. Unfortunately he also used
a common default timeout for both write and erase commands, despite the
fact that erases can take a _whole_ lot longer. Use a more sensible
default for erase timeout.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The newly-added cafe_ecc.c had a lot of it because of the way the lookup
table was auto-generated; clean up the other files too while we're at it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During some testing with several samsung s3c24xx based
devices it was discovered that often the
cfi_cmdset_0001.c would not leave the chip in
read-array mode on suspend. this is an issue if the
same flash chip is used for the bootloader that needs
to be read on resume.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add chip driver and JEDEC probe support for the SST 49LF040B flash chip.
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Jared Hulbert