PWM device setup, and a simple PWM driver exposing a programming interface
giving access to each channel's full capabilities. Note that this doesn't
support starting several channels in synch.
[hskinnemoen@atmel.com: allocate platform device dynamically]
[hskinnemoen@atmel.com: Kconfig fix]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement at32_add_device_cf() which will add a platform_device for
the at32_cf driver (not merged yet). Separate out most of the
at32_add_device_ide() code and use it to implement
at32_add_device_cf() as well.
This changes the API in the following ways:
* The board code must initialize data->cs to the chipselect ID to
use before calling any of these functions.
* The board code must use GPIO_PIN_NONE to indicate unused CF pins.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for adding platform devices for TWI, MCI, AC97C
and ABDAC. They may need to be modified to cope with platform data,
etc. when the corresponding drivers are ready to be merged, but such
changes are much less likely to conflict than adding support for a
whole new type of device.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds platform code for PATA devices on the AP7000.
[hskinnemoen@atmel.com: board code left out for now since stk1000
doesn't support IDE out of the box]
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement at32_add_device_usba() and use it to wire up the USBA device
on ATSTK1000 and ATNGW100.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds register definitions, clocks and IRQs to the platform devices.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Convert the macb driver to use the generic PHY layer in
drivers/net/phy.
Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This modifies and extends the existing lcdc platform code to support
the new atmel_lcdfb driver. The ATSTK1000 board code is set up to use
the on-board Samsung LTV350QV LCD panel.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Set up one spi_board_info array per controller and pass this to
at32_add_device_spi so that it can set up any GPIO pins for chip
selects based on this information.
Extracted from a patch by David Brownell and adapted slightly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The macb driver will probe for the PHY chip and read the mac address
from the MACB registers, so we don't need them in eth_platform_data
anymore.
Since u-boot doesn't currently initialize the MACB registers with the
mac addresses, the tag parsing code is kept but instead of sticking
the information into eth_platform_data, it uses it to initialize
the MACB registers (in case the boot loader didn't do it.) This code
should be unnecessary at some point in the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Allow the board to remap actual USART peripheral devices to serial
devices by calling at32_map_usart(hw_id, serial_line). This ensures
that even though ATSTK1002 uses USART1 as the first serial port, it
will still have a ttyS0 device.
This also adds a board-specific early setup hook and moves the
at32_setup_serial_console() call there from the platform code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the Atmel AVR32 architecture as well as the AT32AP7000
CPU and the AT32STK1000 development board.
AVR32 is a new high-performance 32-bit RISC microprocessor core, designed for
cost-sensitive embedded applications, with particular emphasis on low power
consumption and high code density. The AVR32 architecture is not binary
compatible with earlier 8-bit AVR architectures.
The AVR32 architecture, including the instruction set, is described by the
AVR32 Architecture Manual, available from
http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf
The Atmel AT32AP7000 is the first CPU implementing the AVR32 architecture. It
features a 7-stage pipeline, 16KB instruction and data caches and a full
Memory Management Unit. It also comes with a large set of integrated
peripherals, many of which are shared with the AT91 ARM-based controllers from
Atmel.
Full data sheet is available from
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
while the CPU core implementation including caches and MMU is documented by
the AVR32 AP Technical Reference, available from
http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf
Information about the AT32STK1000 development board can be found at
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918
including a BSP CD image with an earlier version of this patch, development
tools (binaries and source/patches) and a root filesystem image suitable for
booting from SD card.
Alternatively, there's a preliminary "getting started" guide available at
http://avr32linux.org/twiki/bin/view/Main/GettingStarted which provides links
to the sources and patches you will need in order to set up a cross-compiling
environment for avr32-linux.
This patch, as well as the other patches included with the BSP and the
toolchain patches, is actively supported by Atmel Corporation.
[dmccr@us.ibm.com: Fix more pxx_page macro locations]
[bunk@stusta.de: fix `make defconfig']
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Brownell