only return connected if there is actually a
monitor connected.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This moves the radeon DP link training call to happen when we
dpms on the encoder not when we set the mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not returning here caused us to get a display port version of 0 for everything
this caused power up to not get sent which ends up in a black screen.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will be used laster when the encoder and transmitters
are set up.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- keep the atom i2c id in the i2c rec
- fix gpio regs for GPIO and MDGPIO on pre-avivo chips
- track whether the i2c line is hw capable
- track whether the i2c line uses the multimedia i2c block
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- dpcp -> dpcd
- fix up dig encoder routing
- aux transaction table takes delay in 10 usec units
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some BIOSes fail to initialise the GTT, which will cause DMA faults when
the IOMMU is enabled. We need to clear the whole thing to point at the
scratch page, not just the part that Linux is going to use.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[anholt: Note that this may also help with stability in the presence of
driver bugs, by not drawing to memory we don't own]
Signed-off-by: Eric Anholt <eric@anholt.net>
None of the in-tree drivers use user objects yet so this wasn't hitting
us.
Stanse found unreachable code in ttm_bo_add_ttm:
http://decibel.fi.muni.cz/~xslaby/stanse/error.cgi?db=32&id=714#l238
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Both radeon and nouveau can re-use this code so move it up a level
so they can. However the hw interfaces for aux ch are different
enough that the code to translate from mode, address, bytes
to actual hw interfaces isn't generic, so move that code into the
Intel driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
IGD* isn't a useful name. Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
Grab pll ref div from regs at driver init. r4xx seems very
picky about the dividers for the pll driving lvds.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DDX and radeonfb always set these regs to a sane value.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These can end up with garbage otherwise.
fixes rh bug 537140
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
FB read/write really doesn't need to access the actual VRAM, we
can just use a scratch area. This is required for using atom displayport
calls later.
Signed-off-by: Dave Airlie <airlied@redhat.com>
IGD* isn't a useful name. Replace with the codenames, as sourced
from pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
These are handled by the error return being propagated to user-space and
do not any add any information to the original error, so are useless.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch brings the tree up to date with some fixes that were in a
more recent version of the page flipping patch you applied. It fixes
pre-965 flip support, removes a leftover hack that forced alignment,
and initializes the pipe & plane CRTC mappings.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix a crash during boot reported by Jeff Moyer. Fix the issue of accessing
cfqq after freeing it.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
The .probe_valid_hardware low_ops member checked whether the DCTs are in
DDR3 mode and bailed out if so. Now that all the needed changes for DDR3
support is in place, remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Instead of using deeply-nested conditionals for dumping the DIMM type in
debug mode, add a strings array of the supported DIMM types.
This is useful in cases where an edac driver supports multiple DRAM
types and is only defined in debug builds.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add cs mode to cs size mapping tables for DDR2 and DDR3 and F10
and all K8 flavors and remove klugdy table of pseudo values. Add a
low_ops->dbam_to_cs member which is family-specific and replaces
low_ops->dbam_map_to_pages since the pages calculation is a one liner
now.
Further cleanups, while at it:
- shorten family name defines
- align amd64_family_types struct members
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Do not read DCLR[01] again since this is done in
amd64_read_mc_registers() earlier. There can be more than two physical
DIMMs present so clamp the channels value to max 2. Also, do not report
DCT data width - it is also done earlier.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Extend f10_debug_display_dimm_sizes to dump the logical DIMMs
configuration on K8 revF too. Remove the ganged arg since we print the
DCT operating mode (ganged vs unganged) earlier.
Also, DCT csrow configuration is relevant therefore dump it as
KERN_DEBUG instead of only on debug builds. Remove misleading DIMM
output since there's no reliable way of mapping of chip selects to
actual physical DIMMs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Carve out the register-specific debug statements into a separate
function, clarify meanings of the single bitfields in the register,
remove irrelevant output and macros.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a pci config read wrapper for signaling pci config space access
errors instead of them being visible only on a debug build. This is
important on amd64_edac since it uses all those pci config register
values to access the DRAM/DIMM configuration of the nodes.
In addition, the wrapper makes a _lot_ (look at the diffstat!) of
error handling code superfluous and improves much of the overall code
readability by removing error handling details out of the way.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Unify almost identical code into one function and remove NUMA-specific
usage (specifically cpumask_of_node()) in favor of generic topology
methods.
Remove unused defines, while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
cpumask_t -> struct cpumask, and don't put one on the stack. (Note: this
is actually on the stack unless CONFIG_CPUMASK_OFFSTACK=y).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Do not shift the TOP_MEM and TOP_MEM2 values by 23 but rather save the
whole 64-bit value read from the MSR. Although the TOP_MEM/TOP_MEM2 bits
are only a subset of the 64bit register, the values are correct since
the remaining bits are Read-As-Zero and no shifting is needed.
Also, cleanup DRAM base/limit debug output.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Make debug info formulations about the DRAM and DCT configuration of the
machine more human readable.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
I no longer have a machine with this, and as such am not really able
to help out with this driver any more. Remove the entire appletouch
section and let the driver fall under the general input subsystem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Alex Deucher