Setting .ConfigBase and .Present is now done at the pcmcia core.
The driver cleanup missed a few places where the driver did set .Present
to PRESENT_OPTION and later to the values from the CIS. Setting to
PRESENT_OPTION now overrides the values from the CIS. So just remove
those lines.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some PHY trim values need to be fine-tuned on 5755M to be
IEEE-compliant.
Update version to 3.72.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug was a bogus pointer being passed to kfree(). The pointer was
incremented in the write loop and then passed to kfree().
The fix is to use align_buf to save the original address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5709 has a new register to detect copper/fiber PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround is only needed on 5706/5708 and cannot be applied on
5709.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a fix that implements proper communication with the
sideband management unit. Also, it makes sure that the speed is
correctly set for gigabit phys in the case where sideband mgmt unit
initialized the phy. Refer to bug #7684 for more details.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 72f3ab7462, which was
superceded by commit 683a2aa339
("e1000: Do not truncate TSO TCP header with 82544 workaround"), which
fixed the real problem.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When accessing the 93LC86 serial prom the clock high and low times must be at least 250ns each. We have seen on some systems where the access times were much lower casing bit errors.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver TX locking was removed some time ago, but the flag was overlooked.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to disable the AV bit before flushing the low register.
Signed-off-by: <aaron.k.salter@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
A similar patch to commit 65c7973fa5
but now for ixgb.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This fix was already merged in commit 96f9c2e277
but reverted in commit 989316ddfe. After
stresstesting we found that the fix does not add new regressions and
works around a TX hang spotted by several users.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This patch adds support for a few more PHYs used by Apple and fixes
advertising and detecting of Pause (we were missing setting the bit in
MII_ADVERTISE and weren't testing in LPA for all PHYs).
Note that I currently only advertise pause, not asymetric pause. I
don't know for sure the details there, I suppose I should read a bit
more 802.3 references, and I don't now what sungem is capable of, but
I noticed the PCS code (originated from you) does the same.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts drivers/net/loopback.c to using module_init().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_data.header struct is ieee80211_hdr_4addr. If a wireless frame uses
ieee80211_hdr_3addr header and is less than 6 bytes, it will be discarded.
This is not likely going to happen for normal packets (since there is TCP, IP
headers). But if fragmentation is used, there will be such small trailing
packets. And they will be lost for ever.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Checked in Realtek's driver, this one has no business being there.
The driver still works but there is a noticeable performance drop.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This patch removes comment that forcedeth is not supported by NVIDIA.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic.h | 10 +++++-----
1 files changed, 5 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_isr.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_hw.c | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 7 +++++++
1 files changed, 7 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 2 ++
1 files changed, 2 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I have a system with AMCC PowerPC 405EP and PHY Intel LXT971A. Linux
2.6.18.3 is not able to detect the PHY ID correctly. The PHY ID
detected is 0, but should be 0x1d.
This is because phy_read() (__emac_mdio_read() resp.) from
drivers/net/ibm_emac/ibm_emac_core.c might return -ETIMEDOUT or
-EREMOTEIO on error. This is ignored inside the
int mii_phy_probe(struct mii_phy *phy, int address)
from drivers/net/ibm_emac/ibm_emac_phy.c
as the return value is assigned to an u32 variable.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Small cleanup in the Cirrus Logic EP93xx ethernet driver: Check for NULL
pointer before dereferencing it instead of after. Remove unreferenced
variable.
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In order to change PCI registers (via the iomap'd window),
it needs to be enabled; this wasn't being done in sky2_phy_power
the function that turns on/off power to the PHY.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
MSI doesn't work properly on resume on many platforms because the
BIOS goes and changes it back to INTx mode after the sky2 driver has
restored in resume.
It is really a bug in the base power management resume code, and
this workaround is temporary until the change to PM code works it's way
through the release process. The PM fix is non-trivial since it needs
to change when non-boot CPU's are enabled.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Shutting down port 0 disables the NAPI poll used by both ports.
The long term fix will be to separate NAPI object from net device
until then just reenable if needed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
via-velocity doesn't build when CONFIG_INET=n:
drivers/built-in.o: In function `velocity_unregister_notifier':
via-velocity.c:(.text+0xe9b46): undefined reference to `unregister_inetaddr_notifier'
drivers/built-in.o: In function `velocity_init_module':
via-velocity.c:(.init.text+0xa027): undefined reference to `register_inetaddr_notifier'
I wanted to make this change in drivers/net/Kconfig, but
this isn't legal kconfig language:
config VIA_VELOCITY
tristate "VIA Velocity support"
depends on NET_PCI && PCI
+ depends on INET if PM
select CRC32
select CRC_CCITT
select MII
so fix it in via-velocity.c instead.
Builds with all 4 combinations of CONFIG_NET & CONFIG_PM.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The e1000 driver has a workaround for 82544 on PCI-X where if the
terminating byte of a buffer is at addresses 0-3 mod 8, then 4 bytes
are shaved off it and defered to a new segment. This is due to an
erratum that could otherwise cause TX hangs.
Unfortunately this breaks TSO because it may cause the TCP header to
be split over two segments which itself causes TX hangs. The solution
is to pull 4 bytes of data up from the next segment rather than pushing
4 bytes off. This ensures the TCP header remains in one piece and
works around the PCI-X hang.
This patch is based on one from Jesse Brandeburg.
This bug has been trigered by both CONFIG_DEBUG_SLAB as well as Xen.
Note that the only reason we don't see this normally is because the
TCP stack starts writing from the end, i.e., it writes the TCP header
first then slaps on the IP header, etc. So the end of the TCP header
(skb->tail - 1 here) is always aligned correctly.
Had we made the start of the IP header (e.g., IPv6) 8-byte aligned
instead, this would happen for normal TCP traffic as well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
--
Visit Openswan at http://www.openswan.org/
Email: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On suspend, handle pci_set_power_state errors, and on resume
handle failures in pci_resume_state().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCI MSI and express state are already saved and restored by the
current versions of pci_save_state/pci_restore_state.
Therefore it is no longer necessary for the driver to do it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that IRQ are requested is called on open() and freed on close(),
we can safely switch from/to MSI without unloading the module.
We are guaranteed to correctly free IRQ even if the sysfs file got
written in the meantime since the MSI initialization is stored in
mgp->msi_enabled.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Request IRQ in myri10ge_open() and free in close() instead of probe()
and remove() to eliminate potential race between the watchdog and the
interrupt handler. Additionaly, the interrupt handler won't get called
on shared irq anymore when the interface is down.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since pci_save_state() pushes MSI and PCIe states on a kind of stack,
myri10ge saving the state in advance for parity recovery will push the
state again on the stack on suspend. This leads to some memory leak.
We add a couple additional calls to save_state and restore_state so
that we don't leak anymore.
For the future, we are thinking of a better way to recover from parity
error without using pci_save_state().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The former option is removed and platform code can now specify the
expected behavior.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
net/core/netpoll.c::netpoll_send_skb() calls the poll handler when
it is available. As netconsole can be used from almost any context,
IRQ must not be enabled blindly in the NAPI handler of a driver which
supports netpoll.
b57bd06655 fixed the issue for the
8139too.c driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The netxen driver includes a private ioctl that provides access
to functionality that is already available in other ways. The PCI
layer has application access hooks (see setpci), and the statistics
are available in ethtool/netstats.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently after an interface up, the link state is detected 2 seconds later
when the first watchdog timer runs. This patch changes that by triggering
the hardware to generate a link-change interrupt from the up() function
instead. This has the result that the link state gets detected immediately
and without races. This has the potential to speed up booting since a normal
distribution boot process waits for a link before DHCP is attempted.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 3 extra packet redirect counters for tracking purposes to make sure
we can test that all packets arrive properly.
Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>,
rewritten to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the user to vary the size that copybreak works. Currently cb is enabled
for packets < 256 bytes, but various tests indicate that this should be
configurable for specific use cases. In addition, this parameter allows us
to force never/always during testing to get full and predictable coverage of
both code paths.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Assign the PBA to be large enough to contain at least 2 jumbo frames on
all adapters. This dramatically increases performance on several adapters
and fixes TX performance degradation issues where the PBA was misallocated
in the old algorithm.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
the driver has (ancient) code for messing with TIPG from the 82542 days.
Unfortunately this code was running on our current adapters and setting
TIPG for fiber to be +1 over the copper value. This caused 1.45Mpps
to be sent instead of 1.487Mpps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For older adapters we know that they are of the PCI bus type, so we can
just set this.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Daniel Ritz