Loading of modules with unresolved weak symbols fails on MIPS
since '88173507e4fc1e7ecd111b0565e8cba0cb7dae6d'.
Modules: handle symbols that have a zero value
The module subsystem cannot handle symbols that are zero. If symbols
are present that have a zero value then the module resolver prints out a
message that these symbols are unresolved.
We have to use IS_ERR_VALUE() to check that a symbol has been resolved
or not.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks when SMTC support
is enabled on Malta.
Signed-off-by: Raghu Gandham <raghu@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The resume() implementation octeon_switch.S examines the saved cp0_status
register. We were clobbering the entire pt_regs structure in kernel
threads leading to random crashes.
When switching away from a kernel thread, the saved cp0_status is examined
and if bit 30 is set it is cleared and the CP2 state saved into the pt_regs
structure. Since the kernel thread stack overlaid the pt_regs structure
this resulted in a corrupt stack. When the kthread with the corrupt stack
was resumed, it could crash if it used any of the data in the stack that was
clobbered.
We fix it by moving the kernel thread stack down so it doesn't overlay
pt_regs.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cc1: warnings being treated as errors
arch/mips/mipssim/sim_time.c: In function 'get_c0_compare_int':
arch/mips/mipssim/sim_time.c:103: warning: ISO C90 forbids mixed declarations and code
arch/mips/mipssim/sim_time.c:116: error: expected declaration or statement at end of input
make[1]: *** [arch/mips/mipssim/sim_time.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the pagefault oom path which does not drop mm->mmap_sem.
This was introduced by commit c7c1e3846b
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They tend to get not updated when files are moved around or copied and
lack any obvious use. While at it zap some only too obvious comments and
as per Shinya's suggestion, add a copyright header to extable.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
On the good path of BIOS enabled ECC and no override, the value returned
is 1 by omission and thus is deemed failing by the probe-function.
Allow proper module initialization by clearing the retval explicitly.
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The mtdblks array and its content are prone to race conditions. Introduce
the mutex mtdblks_lock in order to solve this.
[Amended by Artem Bityutskiy]
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver is causing build errors and is no longer needed -- it is obsoleted
by physmap_of.
Signed-off-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Tested-on-PPC64-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
GPMC CS was not freed in omap2_onenand_remove() preventing the module
from reloading after removal.
Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes the case where CONFIG_MTD_ONENAND_2X_PROGRAM is set and
the real page size differs from mtd_info.writesize.
Signed-off-by: Mika Korhonen <mika.j.korhonen@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nowadays MTD devices have to be "get" before they can be
used. This has to be done with 'get_mtd_device()'. The
'blktrans_open()' function did not do this and instead
used 'try_module_get()'. Fix this.
Since 'get_mtd_device()' already gets the module, extra
'try_module_get()' is not needed.
This fixes oops when one tries to use mtdblock on top of
gluebi.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch fixes a bug when converting dev to mtd_info by using the
drvdata of the dev, the previous code used
container_of(dev, struct mtd_info, dev), but won't work for the mtdXro
devices as they created without being contained inside mtd_info structure.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When declaring static MTD partitions in board specific code, only
including <include/linux/mtd/partitions.h> should suffice without
gcc nagging us with:
In file included from arch/arm/mach-kirkwood/sheevaplug-setup.c:14:
include/linux/mtd/partitions.h:50: warning: 'struct mtd_info' declared inside parameter list
include/linux/mtd/partitions.h:50: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/mtd/partitions.h:51: warning: 'struct mtd_info' declared inside parameter list
include/linux/mtd/partitions.h:61: warning: 'struct mtd_info' declared inside parameter list
include/linux/mtd/partitions.h:67: warning: 'struct mtd_info' declared inside parameter list
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 24918b61b5 statically changes
the model from dell-bios to dell-3stack to solve the sound decreasing
regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another
problem that the 2nd headphone jack doesn't work
(https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think
the commit 249**2dc is just a workaround. I would like to give a true solution
here.
The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and
the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as
GPIO2. This patch changes EAPD to GPIO0 to solve the problem.
Signed-off-by: Chengu Wang <wangchengu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This converts the last CORBWP access outside of reg_lock.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for safety. azx_init_cmd_io() and azx_free_cmd_io() may be
called when switching to single command mode.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that each codec will have its own module, it is possible
for the user to load one codec while another one is running.
So cmd_mutex would be a safe addition to probe_codec().
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we hit a bug in our dev board, whose HDMI codec#3 may emit
redundant/spurious responses, which were then taken as responses to
command for another onboard Realtek codec#2, and mess up both codecs.
Extend the azx_rb.cmds and azx_rb.res to array and track each codec's
commands/responses separately. This helps keep good codec safe from
broken ones.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use model=lenovo instead of model=dallas for Toshiba Satellite A135-S4527
with ALC861-VD codec.
Reference: Novell bnc#526325
https://bugzilla.novell.com/show_bug.cgi?id=526325
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://neil.brown.name/md:
md: Use revalidate_disk to effect changes in size of device.
md: allow raid5_quiesce to work properly when reshape is happening.
md/raid5: set reshape_position correctly when reshape starts.
md: Handle growth of v1.x metadata correctly.
md: avoid array overflow with bad v1.x metadata
md: when a level change reduces the number of devices, remove the excess.
md: Push down data integrity code to personalities.
md/raid6: release spare page at ->stop()
In cases of fragmented skb, with the data pointers being wrapped around
the TX buffer, the completion handling code would not forward the data
pointer and the firs fragment was unmapped several times, while others
were not unmapped at all.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode. So use that instead of mucking about with locks and
i_size_write.
Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.
Signed-off-by: NeilBrown <neilb@suse.de>
The ->quiesce method is not supposed to stop resync/recovery/reshape,
just normal IO.
But in raid5 we don't have a way to know which stripes are being
used for normal IO and which for resync etc, so we need to wait for
all stripes to be idle to be sure that all writes have completed.
However reshape keeps at least some stripe busy for an extended period
of time, so a call to raid5_quiesce can block for several seconds
needlessly.
So arrange for reshape etc to pause briefly while raid5_quiesce is
trying to quiesce the array so that the active_stripes count can
drop to zero.
Signed-off-by: NeilBrown <neilb@suse.de>
As the internal reshape_progress counter is the main driver
for reshape, the fact that reshape_position sometimes starts with the
wrong value has minimal effect. It is visible in sysfs and that
is all.
Signed-off-by: NeilBrown <neilb@suse.de>
The v1.x metadata does not have a fixed size and can grow
when devices are added.
If it grows enough to require an extra sector of storage,
we need to update the 'sb_size' to match.
Without this, md can write out an incomplete superblock with a
bad checksum, which will be rejected when trying to re-assemble
the array.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
We trust the 'desc_nr' field in v1.x metadata enough to use it
as an index in an array. This isn't really safe.
So range-check the value first.
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is changed from RAID6 to RAID5, fewer drives are
needed. So any device that is made superfluous by the level
conversion must be marked as not-active.
For the RAID6->RAID5 conversion, this will be a drive which only
has 'Q' blocks on it.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.
md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity. The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().
The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.
For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
eeepc-laptop: fix hot-unplug on resume
ACPI: Ingore the memory block with zero block size in course of memory hotplug
ACPI: Don't treat generic error as ACPI error code in acpi memory hotplug driver
ACPI: bind workqueues to CPU 0 to avoid SMI corruption
ACPI: root-only read protection on /sys/firmware/acpi/tables/*
thinkpad-acpi: fix incorrect use of TPACPI_BRGHT_MODE_ECNVRAM
thinkpad-acpi: restrict procfs count value to sane upper limit
thinkpad-acpi: remove dock and bay subdrivers
thinkpad-acpi: disable broken bay and dock subdrivers
hp-wmi: check that an input device exists in resume handler
Revert "ACPICA: Remove obsolete acpi_os_validate_address interface"
Clearly, I am a glutton for punishment. I'll see if I can see Alan's
changes through to the end, otherwise I'll be fending off a lot of bug
reports for usb-serial devices.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function has traditionally used "insert_resource()", because before
commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the
resource into whatever root resource tree that was indicated by
"pcibios_select_root()".
So there Matthew fixed it to actually look up the proper parent
resource, which means that now it's actively wrong to then traverse the
resource tree any more: we already know exactly where the new resource
should go.
And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"),
which changed the x86 PCI code from the open-coded
pr = pci_find_parent_resource(dev, r);
if (!pr || request_resource(pr, r) < 0) {
to using
if (pci_claim_resource(dev, idx) < 0) {
that "insert_resource()" now suddenly became a problem, and causes a
regression covered by
http://bugzilla.kernel.org/show_bug.cgi?id=13891
which this fixes.
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size of receive buffer pointer was used to get size of
receive buffer instead of recvbuf_size itself, so only 4/8
bytes could be transfered.
This is a regression to 2.6.30 introduced by commit 8c90e11e35
mISDN: Use kernel_{send,recv}msg instead of open coding
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the COH 901 327 found in U300 is clocked at 32 kHz we need
to wait for the interrupt clearing flag to propagate through
hardware in order not to accidentally fire off any interrupts
when we enable them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
VLB support has been broken since at least 2004-2005 period as some
changes introduced back then assumed that ->pci_dev is always valid,
lets try to fix it:
- remove duplicated SET_NETDEV_DEV() call
- call SET_NETDEV_DEV() only for PCI devices
- check for ->pci_dev validity in pcnet32_open()
[ Alternatively we may consider removing VLB support but there would not
be much gain in it since an extra driver code needed for VLB support is
minimal and quite simple. ]
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the debug printk() into the proper place and remove superfluous
NULL pointer check in pcnet32_probe1().
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a path when an assetion in dev_unicast_sync() appears.
igmp6_group_added -> dev_mc_add -> __dev_set_rx_mode ->
-> vlan_dev_set_rx_mode -> dev_unicast_sync
Therefore we cannot protect this list with rtnl. This patch restores the
original protecting this list with spinlock.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
In the last iteration i is PHY_MAX_ADDR. the condition
`!(p = pd->mii.bus->phy_map[PHY_MAX_ADDR])' is undefined and may
evaluate to false, which leads to a dereference of this invalid
phy_map in the phy_connect() below.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memcpy() should take into account size of pointers,
not only number of pointers to copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gabor Juhos