Seth reports that some APs, notably the Netgear WNDAP360, send
invalid ECSA IEs in probe response frames with the operating
class and channel number both set to zero, even when no channel
switch is being done. As a result, any scan while connected to
such an AP results in the connection being dropped.
Fix this by ignoring any channel switch announcment in probe
response frames entirely, since we're connected to the AP we
will be receiving a beacon (and maybe even an action frame) if
a channel switch is done, which is sufficient.
Cc: stable@vger.kernel.org # 3.10
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the AP has different regulatory information than we do,
it can happen that we connect to an AP based on e.g. the world
roaming regulatory data, and then update our database with the
AP's country information disables the channel the AP is using.
If this happens on an HT AP, the bandwidth tracking code will
hit the WARN_ON() and disconnect. Since that's not very useful,
ignore the channel-disable flag in bandwidth tracking.
Cc: stable@vger.kernel.org
Reported-by: Chris Wright <chrisw@sous-sol.org>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While we're connected, the AP shouldn't change the primary channel
in the HT information. We checked this, and dropped the connection
if it did change it.
Unfortunately, this is causing problems on some APs, e.g. on the
Netgear WRT610NL: the beacons seem to always contain a bad channel
and if we made a connection using a probe response (correct data)
we drop the connection immediately and can basically not connect
properly at all.
Work around this by ignoring the HT primary channel information in
beacons if we're already connected.
Also print out more verbose messages in the other situations to
help diagnose similar bugs quicker in the future.
Cc: stable@vger.kernel.org [3.10]
Acked-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TX status notification can get lost, or the frames could
get stuck on the queue, so don't wait for the callback
from the driver forever and instead time out after half
a second.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "3d9646d mac80211: fix channel selection bug" introduced a possible
infinite loop by moving the out target above the chandef_downgrade
while loop. When we downgrade to NL80211_CHAN_WIDTH_20_NOHT, we jump
back up to re-run the while loop...indefinitely. Replace goto with
break and carry on. This may not be sufficient to connect to the AP,
but will at least keep the cpu from livelocking. Thanks to Derek Atkins
as an extra pair of debugging eyes.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some regulations (like germany, but also FCC) express their transmission
power limit in dBm/MHz or mW/MHz. To cope with that and be on the safe
side, reduce the maximum power to half (10 MHz) or quarter (5 MHz)
when operating on these reduced bandwidth channels.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)
This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a collection of minor fixes:
* don't allow HT IEs in IBSS for 5/10 MHz
* don't allow HT IEs in Mesh for 5/10 MHz
* don't downgrade from/to 5 and 10 MHz channels
* don't try HT rates for 5 and 10 MHz channels when selecting rates
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track the AP's beacon rate in the scan BSS data and in the
interface configuration to let the drivers know which rate
the AP is using. This information may be used by drivers,
in our case to let the firmware optimise beacon RX.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some APs, notably 2G/3G/4G Wifi routers, specifically the
"Onda PN51T", "Vodafone PocketWiFi 2", "ZTE MF60" and a similar
T-Mobile branded device [1] that erroneously don't include all the
needed information in (re)association response frames. Work around
this by assuming the information is the same as it was in the
beacon or probe response and using the data from there instead.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58881.
[1] https://bbs.archlinux.org/viewtopic.php?pid=1277305
Note that this requires marking the first ieee802_11_parse_elems()
argument const, otherwise we'd get a compiler warning.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Michal Zajac <manwe@manwe.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_rx_bss_info() deals with dtim_period setting and PS update
when associated. Move all these to another locations cleaning this
function. Also, the current implementation is buggy because when it
calls ieee80211_recalc_ps() bss_conf->dtim_period is notset properly
yet and thus nothing will happen.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The connection monitor needs to know the tx status of
nullframes to work properly.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We send direct probe to broadcast address, as some APs do not respond to
unicast PROBE frames when unassociated. Broadcast frames are not acked,
so we can not use that for trigger MLME state machine, but we need to
use old timeout mechanism.
This fixes authentication timed out like below:
[ 1024.671974] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 1024.694125] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 1024.695450] wlan6: direct probe to 54:e6:fc:98:63:fe (try 2/3)
[ 1024.700586] wlan6: send auth to 54:e6:fc:98:63:fe (try 3/3)
[ 1024.701441] wlan6: authentication with 54:e6:fc:98:63:fe timed out
With fix, we have:
[ 4524.198978] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 4524.220692] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 4524.421784] wlan6: send auth to 54:e6:fc:98:63:fe (try 2/3)
[ 4524.423272] wlan6: authenticated
[ 4524.423811] wlan6: associate with 54:e6:fc:98:63:fe (try 1/3)
[ 4524.427492] wlan6: RX AssocResp from 54:e6:fc:98:63:fe (capab=0x431 status=0 aid=1)
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generally, the DTIM period is available after a beacon has
been received, and if no beacon has been received enabling
powersave is problematic anyway for synchronisation. Since
some drivers may require the DTIM period for powersave,
don't enable powersave until it becomes available in case
the scan/association managed to not receive a beacon.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an HT AP is advertising channel switch in a beacon, it
doesn't (and shouldn't, according to 802.11-2012 Table 8-20)
include a secondary channel offset element. The only possible
interpretation is that the previous secondary channel offset
remains valid, so use that when switching channel based only
on beacon information.
VHT requires the Wide Bandwidth Channel Switch subelement to
be present in the Channel Switch Wrapper element, so the code
for that is probably ok (see 802.11ac Draft 4, 8.4.2.165.)
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the frame isn't transmitted to the AP, we need to
report it to cfg80211 so the state there can be updated
correctly.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an HT AP is advertising channel switch in a beacon, it
doesn't (and shouldn't, according to 802.11-2012 Table 8-20)
include a secondary channel offset element. The only possible
interpretation is that the previous secondary channel offset
remains valid, so use that when switching channel based only
on beacon information.
VHT requires the Wide Bandwidth Channel Switch subelement to
be present in the Channel Switch Wrapper element, so the code
for that is probably ok (see 802.11ac Draft 4, 8.4.2.165.)
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 12e7f51702,
IEEE80211_SDATA_DISCONNECT_RESUME no longer worked as
it would simply never be tested. Restore a bit of the
code removed there and in 9b7d72c104
to make it work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some driver implementations need to know whether mandatory
admission control is required by the AP for some ACs. Add
a parameter to the TX queue parameters indicating this.
As there's currently no support for admission control in
mac80211's AP implementation, it's only ever set for the
client implementation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 assumes that connection monitor offload
for BSS station implies that the device:
- sends periodic keep alive packets to associated AP
- monitors missed beacons
- actively probes the AP in case of missed beacons
In case of poor connection conditions it expects the function
ieee80211_connection_loss() to be called by driver. However,
some devices implement connection monitor offload excluding
active AP probing.
To allow them to call ieee80211_beacon_loss() cleanly, remove
the warning there and thus allow them to use mac80211 for the
AP probing even if connection monitor offload is supported.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parse and react to the wide bandwidth channel switch element
in beacons/action frames. Finding the element was done in a
previous patch (it has different positions in beacons/action
frames), now handle it. If there's something wrong with it
simply disconnect.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT introduces multiple IEs that need to be parsed for a
wide bandwidth channel switch. Two are (currently) needed
in mac80211:
* wide bandwidth channel switch element
* channel switch wrapper element
The former is contained in the latter for beacons and probe
responses, but not for the spectrum management action frames
so the IE parser needs a new argument to differentiate them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Handle the (public) extended channel switch announcement
action frames. Parts of the data in these frames isn't
really in IEs, but put it into the elems struct anyway
to simplify the handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support extended channel switch when the operating
class is one of the global operating classes as
defined in Annex E of 802.11-2012. If it isn't,
disconnect from the AP instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CSA action frame content should be processed as variable IEs
rather than fixed to make it extensible. Unify the code and
process them just like CSA in beacons to make it easier to
extend for HT/VHT.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field is otherwise reserved, so we shouldn't read
and reject it, though any sane system will probably
have to set it to 0 anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If authentication (or association with FT) is requested by
userspace, mac80211 currently doesn't tell cfg80211 that it
disconnected from the AP. That leaves inconsistent state:
cfg80211 thinks it's connected while mac80211 thinks it's
not. Typically this won't last long, as soon as mac80211
reports the new association to cfg80211 the old one goes
away. If, however, the new authentication or association
doesn't succeed, then cfg80211 will forever think the old
one still exists and will refuse attempts to authenticate
or associate with the AP it thinks it's connected to.
Anders reported that this leads to it taking a very long
time to reconnect to a network, or never even succeeding.
I tested this with an AP hacked to never respond to auth
frames, and one that works, and with just those two the
system never recovers because one won't work and cfg80211
thinks it's connected to the other so refuses connections
to it.
To fix this, simply make mac80211 tell cfg80211 when it is
no longer connected to the old AP, while authenticating or
associating to a new one.
Cc: stable@vger.kernel.org
Reported-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise STBC capabilities and MCS rates even if the AP
doesn't support them. This has always been the right thing
to do, but used to be problematic with some APs. Now WFA
testing requires this so re-enable it, problematic APs
would then presumably not pass the test and be fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The netdev queues should always represent the state that
the driver gave them, so fiddling with them isn't really
appropriate in the mlme code. Also, since we stop queues
for flushing now, this really isn't necessary any more.
As the scan/offchannel code has also been modified to no
longer do this a while ago, remove the outdated smp_mb()
and comments about it.
While at it, also add a pair of braces that was missing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's unlikely that an AP requires WMM mandatory admission control
for all access categories, and if it does then we still transmit
on the background AC without requesting admission. However, avoid
using uAPSD in this case since the implementation could run into
issues and might use other ACs etc.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open-coding the accesses and length check do
the length check in the IE parser and assign a struct
pointer for use in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I don't think we should send the events unless it was actually
a beacon that was lost...not just any probe of an AP.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 currently sets uAPSD parameters to have VO AC trigger-
and delivery-enabled, with maximum service period length.
Allow drivers to change these default settings since different
uAPSD client implementations may handle errors differently and
be able to recover from some errors.
Note: some APs may not function correctly if one or all ACs are
trigger- and delivery-enabled, see
http://thread.gmane.org/gmane.linux.kernel.wireless.general/93577.
We retested with this AP and later firmware doesn't have this
bug any more.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I found another crash when deleting lots of virtual stations
in a congested environment. I think the problem is that
the ieee80211_mlme_notify_scan_completed could call
ieee80211_restart_sta_timer for a stopped interface
that was about to be deleted.
With the following patch I am unable to reproduce the
crash.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[move check, also make the same change in mesh]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add P2P NoA settings for STA mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use ieee80211_p2p_noa_attr structure during
P2P_PS (oppps) detection.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On loaded systems with lots of VIFs, I see lots of beacon
timeouts, even though the connection to the AP is very
good. Allow tuning the beacon-loss-count variable to
give the system longer to process beacons if the user
prefers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[add the number of beacons to the message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove not used any longer suspend/resume code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg