The auto selection of pertinent helper chips (VIDEO_HELPER_CHIPS_AUTO)
should select the wm8775 driver, which is used by at least one
Conexant 2388x based card (Hauppauge HVR-1300), if VIDEO_CX88 is
selected.
Signed-off-by: Frej Drejhammar <frej.drejhammar@gmail.com>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All cx2388 boards need the line-in audio to be routed from an external ADC
(refered to as "ADC mode" in the spec sheet), since the chip is uncapable
of dealing with baseband audio directly.
So... this patch enables normal mode when using the tuner (TV or Radio), and
enables ADC mode with any other source. It'll probably only work with boards
that have supported ADCs (such as the Wolfson wm9775)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should not mute the audio input when we stop the codec,
because it will interfere with the live uncompressed stream.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds.
The wm8775 module initializes the audio input at "route 2", which doesn't
hold true for all boards. The HVR-1300, for example, uses route 1 for
tuner audio, and route 2 for baseband. So we must route the audio to the
proper input depending on what video input is being used.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in
cx88-blackbird.c
The encoder is never muted, hence unmuting should then only be necessary
once after hardware initialization.
I tested this from warm boots and cold boots (with long power down time
to ensure the sram in the chip is emptied), and found that after the
firmware upload the encoder is apparently not muted, making the unmutes
unnecessary.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch should fix the 'muted audio' and 'raspy audio' problem for
mpeg2 streams out of cx88-blackbird devices.
Especially mythtv users would find that the audio would often sound bad
(aliased, or 'raspy'), mainly related to channel changes, many (all?)
other users would find that there was no audio at all in the mpeg data
from the encoder chip, unless the audio was manually unmuted.
The patch includes the following modifications:
Don't actually start the mpeg2 encoder until the device is read from
by the application.
Wait until the audio is stable for at least 400ms before starting the
mpeg encoder.
Mute/Unmute the audio when starting/stopping the mpeg encoder.
Stop the mpeg encoder when changing parameters and when changing tuner
frequency.
Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of
whether or not the mpeg2 encoder is active.
Load the firmware on cx88-blackbird driver load.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATSC standard-specific firmware is D2633 on both v2.5 and v2.7. Better to
auto-select this firmware, overriding ctrl.d2633.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use VSB IF frequency ( 44 / 5.38 MHz ) if qam_if is invalid or unspecified
Acked-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On the s5h1409 demod, the IF frequency for VSB is limited to 44 / 5.38 MHz.
Hardcode VSB IF frequency within the driver to 44 / 5.38 MHz.
QAM IF frequency remains configurable via attach-time configuration.
Acked-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ctrlUrbLock has all it's users commented out, and so it's unused. This
patch removes it.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are a few error paths which don't unlock the usbvision->lock.
So I've added mutex_unlock() calls to fix those paths.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/et61x251/et61x251_core.c:390: warning: 'et61x251_i2c_read' defined but not used
drivers/media/video/et61x251/et61x251_core.c:397: warning: 'et61x251_i2c_write' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If we pass TDA18271_GATE_DIGITAL into tda18271_attach(), it will always try to
use the digital demodulator's i2c gate.
If we pass TDA18271_GATE_ANALOG into tda18271_attach(), it will always try to
use the analog demodulator's i2c gate.
If we pass TDA18271_GATE_AUTO into tda18271_attach(), it will try to use the
analog demodulator's i2c gate when tuning in analog mode, and it will try to
use the digital demodulator's i2c gate when tuning in digital mode.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use an enum rather than an integer #define to store analog / digital state.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Those newer functions are used by saa7134-empress. Adds export for them:
+EXPORT_SYMBOL_GPL(saa7134_g_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_s_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_queryctrl);
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134 were converted to video_ioctl2, but saa7134_empress weren't. This broke
saa7134-empress, since it were dependent of saa7134_common_ioctl.
With the conversion, the module had a size decrease of 436 bytes on x86_64:
text data bss dec hex filename
5196 4912 4 10112 2780 old/saa7134-empress.ko
4760 4912 4 9676 25cc new/saa7134-empress.ko
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VBI were broken, since there weren't any function handlers for it. This patch
fixes it, by removing the vbi_template, using, instead video_template.
This also saves some space at the data segment.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some functions are used also by saa7134-empress, and need to be exported. To
avoid namespace confusion, rename all of them to saa7134_
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't waste 128 bytes of memory for a name that might not actually need it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix codingstyle issue discovered after using new checkpatch.pl
ERROR: open brace '{' following struct go on the same line
396: FILE: linux/drivers/media/video/tda8290.h:24:
+struct tda829x_config
+{
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Store the analog demodulator name in fe.ops.analog_demod_ops.info.name
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- remove dependency of tda8290 module on struct tuner
- move tuner_foo printk macros from tuner-driver.h into tuner-core.c
- clean up #includes of tuner-i2c.h / tuner-driver.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Always call tda829x_release if tda829x_attach fails for a reason
other than failure to allocate memory for private structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We can tell whether we are tuning television or radio by testing for
struct analog_parameters *params->mode == V4L2_TUNER_RADIO
There is no longer any need for separate set_tv_freq and
set_radio_freq functions in the analog tuner demodulator modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix "warning: Using plain integer as NULL pointer".
Convert 'x < y ? x : y' to use min() instead.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver tries to keep all device specific attributes in a
single data structure in one source file. This change further cleans
up how that table is set up. We now try to group everything together
for each specific device, and the number of symbols exported from this
module has now been reduced to a single global.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the AVerMedia EZMaker PCI Deluxe and update the ivtv cardlist.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab