Broken by 4a1728a28a which switched the
return semantics of read_mii_word() but didn't fix usage of
read_mii_word() to conform to the new semantics.
Setting carrier to off based on the NO_CARRIER flag is also incorrect as
that flag only triggers on TX failure and therefore isn't correct when
no frames are being transmitted. Since there is already a 2*HZ MII
carrier check going on, defer to that.
Add a TRUST_LINK_STATUS feature flag for adapters where the LINK_STATUS
flag is actually correct, and use that rather than the NO_CARRIER flag.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
the Nikon D80 camera will not work without an UNUSUAL_DEV entry embodied
in the attached patch (made against 2.6.20.3). Hope you find it helpful,
or if not, pass it along to someone who does.
From: Emil Larsson <emil@swip.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is one significant difference between the behavior of root hubs
(as embodied in host controller hardware) and external hubs: When a
remote-wakeup signal is received, an external hub sends an interrupt
message at the _end_ of the resume sequence but a root hub generates
and interrupt at the _beginning_ of the resume sequence. The host
system must poll for the end of the sequence.
When ehci-hcd was converted to interrupt-driven operation instead of
using polling, the remaining need for this particular poll was
overlooked. This patch (as894) fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning:
drivers/usb/serial/ftdi_sio.c:890: warning: enumeration value `FT232RL' not handled in switch
Also add logic to detect FT232R chips (version 6.00, usb 2.0 full speed),
so that case isn't completely useless. (NOTE: FT232RL and FT232RQ are
the same chip in different packages: L is SSOP, Q is QFN.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning when CONFIG_USB_SERIAL_GENERIC is undefined.
drivers/usb/serial/generic.c:24: warning: `generic_probe' declared `static' but never defined
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both airprime and option now want to handle vendor ID 0x1410,
device ID 0x1100. Airprime calls it 'ExpressCard34 Qualcomm 3G CDMA'.
Option calls it 'Novatel Merlin XS620/S640'. Patch attached to remove it
from airprime.
From: Jon K Hellan <jon.kare.hellan@uninett.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to omap_udc, noted with some recent testing:
- Cope with some SMP-induced braindamage in ARM's dma_{alloc,free}_coherent()
implementation: alloc() can be called with IRQs blocked, but since late
last year that's no longer true for free(). This resolves really NASTY
problems with logspamming via WARN_ON(), indicating N-page leaks.
- Be more correct in handling GET_STATUS request for RECIP_ENDPOINT ... the
previous code only handled RECIP_INTERFACE, this version should be correct
except for (sigh) bulk/interrupt endpoints.
- Provide a better name for the function reporting whether the board has
vbus sensing wired up.
GET_STATUS requests for endpoint status still acts strangely though, at least
given one flakey host doesn't always ack the first DATA packet, then the packet
that gets retransmitted doesn't have data!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as871) fixes a problem introduced by an earlier change.
It turns out that some systems really do need to have a terminating
skeleton QH present whenever FSBR is on. I don't know any way to tell
which systems do need it and which don't; the easiest answer is to
have it there always.
This fixes the NumLock-hang bug reported by Jiri Slaby.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves all of the Novatel device ids to the option driver, where
they belong.
Thanks to Novatel for providing a list of all supported devices.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was testing the berry_charge module with my Blackberry 8700c and had
great success, thanks. Looking at the code for my own learning I noticed
the following cut and paste error... just a nit.
Signed-off-by: Ken L Johnson <ken@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as872) adds a device table entry and a new quirk flag to
the usblp driver for the Seiko Epson Receipt printer. This printer
returns Vendor-Specific values for bInterfaceClass and
bInterfaceSubClass, but the bInterfaceProtocol value is valid and it
works with usblp. The new quirks flag tells the driver to ignore the
Class and SubClass values in the interface descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an ID to recognise the Novatel EV620 wireless adapter.
http://www.novatelwireless.com/products/expedite/ev620.html
It looks like a mini PCI-Express adapter. The mPCIE connector includes USB
pins... the card shows up to the system as a USB device, and powers itself
from the PCI bus.
The card I have isn't activated yet, so I can't get a PPP session up yet, but
I have tested basic serial communication successfully in both 2.6.18 and
2.6.20 kernels, once the product ID was added. (the driver changed quite a
bit between the two revs.) In both drivers, it responds to AT commands and
such.
Signed-off-by: Mark Glines <mark@glines.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these devices have a shared interrupt endpoint. For serialcore to pass
an interrupt endpoint to a subdriver, the subdriver must define and
_export_ a fitting callback. The mos7720 driver failed to do so. This led
invariably to an oops upon open. This patch fixes it. The driver is useless
without it. Please try to get this into 2.6.21 and the stable kernels that
have this driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual_devs entry for the Motorola RAZR 3vi.
From: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for the linux-usb-devel tree adds two more
product ids to the dm9601 driver. These ids were found on
rebadged dm9601 devices in the wild.
Signed-off-by: Jon Dowland <jon@alcopop.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts d9a7ecacac since it
breaks drivers that need to access the ->port[] array in shutdown
(most of them).
Signed-Off: Jim Radford <radford@blackbean.org>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit d2487cb425.
Russell King points out that it's obviously bogus, and I have to agree.
Not only does "irq" not even exist in that scope, but we obviously need
to free the irq that we actually requested, and that's IRQ_USB.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>,
Cc: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]
Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
>
> 34ef50e5b1 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.
This patch should fix the issue.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:
Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem. Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.
With the attached patch, the RTS/DTR lines are resetted on a close. The
code was mainly taken from the option.c driver.
Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
I use the FTDI VID 0x0403. My PID's are:
0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device
The company is "IBS Ing.-Buero Schleusener".
From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here are two new device IDs for the cp2101 driver.
The diff is with linus's tree as of this evending.
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flaky hardware can cause a lot of debounce failed messages. To limit
the performance impact, a ratelimit should be used.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes last use of hardcoded number of irq to
use platfrom_get_irq.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller. The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as862) fixes a couple of bugs in the way usbcore handles
intervals for interrupt URBs. usb_interrupt_msg (and usb_bulk_msg for
backward compatibility) don't set the interval correctly for
high-speed devices. proc_do_submiturb() doesn't set it correctly when
a bulk URB is submitted to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is deep architecture specific magic and does should not to exist
in a driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an usual_devs entry for the Nokia 6288. Originally from
Andrew with a re-diff by Phil.
From: Andrew Nayenko <relan@bk.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the duplicate supertop entries that made it into the
.21 rc kernels.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename the driver struct used with at91_udc to prevent yet another
bogus warning from "modpost".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replacing use of UTS_RELEASE with utsname()->release avoids that the
usb-storage driver is recompiled each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put all Code Mercenaries (VID 0x07c0) IOWarriors (PIDs 0x1500 to 0x15ff) on
the HID blacklist. The range of PIDs has been reserved for IOWarriors. Only
5 PIDs are really used yet.
Signed-off-by: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dongle shipped with Logitech DiNovo Edge (0x046d/0xc714) behaves in a weird
non-standard way - it contains multiple reports with the same usage, which
results in remapping of GenericDesktop.X and GenericDesktop.Y usages to
GenericDesktop.Z and GenericDesktop.RX respectively, thus rendering the
touchwheel unusable.
The commit 3506897691 solved this
in a way that it didn't remap certain usages. This however breaks
(at least) middle button of Logic3 / SpectraVideo (0x1267/0x0210),
which in contrary requires the remapping.
To make both of the harware work, allow remapping of these usages again,
and introduce a quirk for Logitech DiNovo Edge "touchwheel" instead - we
disable remapping for key, abs and rel events only for this hardware.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes extra keys (F1-F12 in special mode, zooming, rotate, shuffle)
on Logitech S510 keyboard work.
Logitech S510 keyboard sends in report no. 3 keys which are far above the
logical maximum described in descriptor for given report.
This patch introduces a HID quirk for this wireless USB receiver/keyboard
in order to fix the report descriptor before it's being parsed - the logical
maximum and the number of usages is bumped up to 0x104d). The values are in the
"Reserved" area of consumer HUT, so HID_MAX_USAGE had to be changed too.
In addition to proper extracting of the values from report descriptor, proper
HID-input mapping is introduced for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report descriptor should be output when CONFIG_HID_DEBUG is defined.
This also mitigates the need for DEBUG and DEBUG_DATA defines, so let's
remove them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB vendor and product IDs are not byteswapped appropriately, and
thus come out in the wrong endianness when fetched through the evdev
using ioctl() on big endian platforms.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as861) adds sysfs attributes to expose the autosuspend
delay value for each USB device. If the user changes the delay from 0
(no autosuspend) to a positive value, an autosuspend is attempted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as859) makes the default USB autosuspend delay a module
parameter of usbcore. By setting the delay value at boot time, users
will be able to prevent the system from autosuspending devices which
for some reason can't handle it.
The patch also stores the autosuspend delay as a per-device value. A
later patch will allow the user to change the value, tailoring the
delay for each individual device. A delay value of 0 will prevent
autosuspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as858) makes some minor cleanups to sysfs.c in usbcore.
Unnecessary tests are removed and a few temp variables are added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Williams