The bonding driver calls ndo_vlan_rx_register() while holding bond->lock.
The bnx2 driver calls bnx2_netif_stop() to stop the rx handling while
changing the vlgrp. The call also stops the cnic driver which sleeps
while the bond->lock is held and cause the warning.
This code path only needs to stop the NAPI rx handling while we are
changing the vlgrp. Since no reset is going to occur, there is no need
to stop cnic in this case. By adding a parameter to bnx2_netif_stop()
to skip stopping cnic, we can avoid the warning.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that under certain heavy traffic conditions in MSI-X
mode, the driver can lose an MSI-X vector causing all packets in the
associated rx/tx ring pair to be dropped. The problem is caused by
the chip dropping the write to unmask the MSI-X vector by the kernel
(when migrating the IRQ for example).
This can be prevented by increasing the GRC timeout value for these
register read and write operations.
Thanks to Dell for helping us debug this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some Power7 platforms, when using VIOS (Virtual I/O Server), we
need to wait longer for control packets to finish transfer during
initialization.
Without this change, initialization may fail prematurely.
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prompted by a previous patch submitted by Matthew Garret <mjg@redhat.com>,
further digging into errata documentation reveals the current enabling or
disabling of ASPM L0s and L1 states for certain parts supported by this
driver are incorrect. 82571 and 82572 should always disable L1. For
standard frames, 82573/82574/82583 can enable L1 but L0s must be disabled,
and for jumbo frames 82573/82574 must disable L1. This allows for some
parts to enable L1 in certain configurations leading to better power
savings.
Also according to the same errata, Early Receive (ERT) should be disabled
on 82573 when using jumbo frames.
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY laser is still on during driver init. It's allowing
garbage to hit our FIFO, which eventually can cause the entire
device to die. Power down the laser while setting up the device,
and re-enable the laser before getting link.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checks for CONFIG_MMU at this location are duplicated as all the code is
located inside a #ifndef CONFIG_MMU block. So the first conditional block will
always be included while the second never will.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
Check whether the VMA has a vm_ops before calling close, just
like we check vm_ops before calling open a few dozen lines
higher up in the function.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Fix sparc regression in r300_scratch()
drm: make sure vblank interrupts are disabled at DPMS time
drm/radeon/kms/evergreen: No EnableYUV table
drm/radeon: 9800 SE has only one quadpipe
drm/radeon/kms: don't print error for legal crtcs.
drm/radeon/kms/evergreen: fix LUT setup
Currently, device claiming for exclusive open is done after low level
open - disk->fops->open() - has completed successfully. This means
that exclusive open attempts while a device is already exclusively
open will fail only after disk->fops->open() is called.
cdrom driver issues commands during open() which means that O_EXCL
open attempt can unintentionally inject commands to in-progress
command stream for burning thus disturbing burning process. In most
cases, this doesn't cause problems because the first command to be
issued is TUR which most devices can process in the middle of burning.
However, depending on how a device replies to TUR during burning,
cdrom driver may end up issuing further commands.
This can't be resolved trivially by moving bd_claim() before doing
actual open() because that means an open attempt which will end up
failing could interfere other legit O_EXCL open attempts.
ie. unconfirmed open attempts can fail others.
This patch resolves the problem by introducing claiming block which is
started by bd_start_claiming() and terminated either by bd_claim() or
bd_abort_claiming(). bd_claim() from inside a claiming block is
guaranteed to succeed and once a claiming block is started, other
bd_start_claiming() or bd_claim() attempts block till the current
claiming block is terminated.
bd_claim() can still be used standalone although now it always
synchronizes against claiming blocks, so the existing users will keep
working without any change.
blkdev_open() and open_bdev_exclusive() are converted to use claiming
blocks so that exclusive open attempts from these functions don't
interfere with the existing exclusive open.
This problem was discovered while investigating bko#15403.
https://bugzilla.kernel.org/show_bug.cgi?id=15403
The burning problem itself can be resolved by updating userspace
probing tools to always open w/ O_EXCL.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Matthias-Christian Ott <ott@mirix.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor out bd_may_claim() from bd_claim(), add comments and apply a
couple of cosmetic edits. This is to prepare for further updates to
claim path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
commit 42747d712d ("[WATCHDOG] watchdog_info
constify") introduced the following build failure:
CC booke_wdt.o
booke_wdt.c: In function 'booke_wdt_init':
booke_wdt.c:220: error: assignment of read-only variable 'ident'
Fix this by removing 'const' qualifier from watchdog_info struct.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
They will be holding dirty inodes and be responsible for flushing
them out, so they need to be setup properly.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Removes one .h and one .c file that are never used outside of
mtdcore.c.
Signed-off-by: Joern Engel <joern@logfs.org>
Edited to remove on leftover debug define.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit b4fe945405 ("drm/radeon: Fix
memory allocation failures in the preKMS command stream checking.")
added a regression in that it completely tossed the get_unaligned()
done by r300_scratch() which we added in commit
958a6f8ccb ("drm: radeon: Fix unaligned
access in r300_scratch().").
Put it back.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we call drm_vblank_off() at DPMS off time (to wake any clients so
they don't hang) we need to make sure interrupts are actually disabled.
If drm_vblank_off() gets called before the vblank usage timer expires,
it'll prevent the timer from disabling interrupts since it also clears
the vblank_enabled flag for the pipe.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
78f1cd0245 ("fix broken register writes")
does not work for Al Viro's r8169 (XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few (6) network drivers enable mwi explicitly. Fewer worry about a
failure.
It is not a fix but it should avoid some annoyance like
http://bugzilla.kernel.org/show_bug.cgi?id=15454
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Conrad Kostecki <conikost@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When read_buf is called to move over to the next page in the pagelist
of an NFSv4 request, it sets argp->end to essentially a random
number, certainly not an address within the page which argp->p now
points to. So subsequent calls to READ_BUF will think there is much
more than a page of spare space (the cast to u32 ensures an unsigned
comparison) so we can expect to fall off the end of the second
page.
We never encountered thsi in testing because typically the only
operations which use more than two pages are write-like operations,
which have their own decoding logic. Something like a getattr after a
write may cross a page boundary, but it would be very unusual for it to
cross another boundary after that.
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
When we move a PCI device or assign resources to a device not configured
by the BIOS, we want to avoid the BIOS region below 1MB. Note that if the
BIOS places devices below 1MB, we leave them there.
See https://bugzilla.kernel.org/show_bug.cgi?id=15744
and https://bugzilla.kernel.org/show_bug.cgi?id=15841
Tested-by: Andy Isaacson <adi@hexapodia.org>
Tested-by: Andy Bailey <bailey@akamai.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Even with commit 32dec5dd02 ("bridge
br_multicast: Don't refer to BR_INPUT_SKB_CB(skb)->mrouters_only
without IGMP snooping."), BR_INPUT_SKB_CB(skb)->mrouters_only is
not appropriately initialized if IGMP snooping support is
compiled and disabled, so we can see garbage.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock need to be replaced by mutex because of sleep functions
inside wdt_send_data.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Trying to run izlisten (from lowpan-tools tests) on a device that does not
exists I got the oops below. The problem is that we are using get_dev_by_name
without checking if we really get a device back. We don't in this case and
writing to dev->type generates this oops.
[Oops code removed by Dmitry Eremin-Solenikov]
If possible this patch should be applied to the current -rc fixes branch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are fitpc2 compatible boards that hang with existent i/o
operations order. Solution is to switch between writing to data
and command ports.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
tg3: Fix INTx fallback when MSI fails
MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.
In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Watchdog configuration register and timer count register were interchanged,
causing wrong values to be written into both registers.
This caused watchdog triggered resets even if the watchdog was reset in time.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Prevent PCMCIA_DEV_ID_MATCH_FUNC_ID from grabbing PFC-cards:
I changed the code, so that the first matching struct
pcmcia_device_id _PFC_ entry will mark the card has_pfc,
preventing PCMCIA_DEV_ID_MATCH_FUNC_ID to match.
[linux-pcmcia@lists.infradead.org: re-order commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A new xfsqa test (226) with a prototype xfs_fsr change to try to
handle dynamic fork offsets better triggers an assertion failure
where the inode data fork is in btree format, yet there is room in
the inode for it to be in extent format. The two inodes look like:
before: ino 0x101 (target), num_extents 11, Max in-fork extents 6, broot size 40, fork offset 96
before: ino 0x115 (temp), num_extents 5, Max in-fork extents 3, broot size 40, fork offset 56
after: ino 0x101 (target), num_extents 5, Max in-fork extents 6, broot size 40, fork offset 96
after: ino 0x115 (temp), num_extents 11, Max in-fork extents 3, broot size 40, fork offset 56
Basically the target inode ends up with 5 extents in btree format,
but it had space for 6 extents in extent format, so ends up
incorrect. Notably here the broot size is the same, and that is
where the kernel code is going wrong - the btree root will fit, so
it lets the swap go ahead.
The check should not allow the swap to take place if the number of
extents while in btree format is less than the number of extents
that can fit in the inode in extent format. Adding that check will
prevent this swap and corruption from occurring.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This patch fixes few usability and configurability issues.
o All the cgroup based controller options are configurable from
"Genral Setup/Control Group Support/" menu. blkio is the only exception.
Hence make this option visible in above menu and make it configurable from
there to bring it inline with rest of the cgroup based controllers.
o Get rid of CONFIG_DEBUG_CFQ_IOSCHED.
This option currently does two things.
- Enable printing of cgroup paths in blktrace
- Enables CONFIG_DEBUG_BLK_CGROUP, which in turn displays additional stat
files in cgroup.
If we are using group scheduling, blktrace data is of not really much use
if cgroup information is not present. To get this data, currently one has to
also enable CONFIG_DEBUG_CFQ_IOSCHED, which in turn brings the overhead of
all the additional debug stat files which is not desired.
Hence, this patch moves printing of cgroup paths under
CONFIG_CFQ_GROUP_IOSCHED.
This allows us to get rid of CONFIG_DEBUG_CFQ_IOSCHED completely. Now all
the debug stat files are controlled only by CONFIG_DEBUG_BLK_CGROUP which
can be enabled through config menu.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Divyesh Shah <dpshah@google.com>
Reviewed-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When Steffen originally wrote the authenc async hash patch, he
correctly had EINPROGRESS checks in place so that we did not invoke
the original completion handler with it.
Unfortuantely I told him to remove it before the patch was applied.
As only MAY_BACKLOG request completion handlers are required to
handle EINPROGRESS completions, those checks are really needed.
This patch restores them.
Reported-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit fda48a0d7a (tcp: bind() fix when many ports are bound)
introduced a bug on IPV6 part.
We should not call ipv6_addr_any(inet6_rcv_saddr(sk2)) but
ipv6_addr_any(inet6_rcv_saddr(sk)) because sk2 can be IPV4, while sk is
IPV6.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Issue the discard operation *before* releasing the blocks to be reused
ext4: Fix buffer head leaks after calls to ext4_get_inode_loc()
ext4: Fix possible lost inode write in no journal mode
noop_backing_dev_info is used only as a flag to mark filesystems that
don't have any backing store, like tmpfs, procfs, spufs, etc.
Signed-off-by: Joern Engel <joern@logfs.org>
Changed the BUG_ON() to a WARN_ON(). Note that adding dirty inodes
to the noop_backing_dev_info is not legal and will not result in
them being flushed, but we already catch this condition in
__mark_inode_dirty() when checking for a registered bdi.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Nothing stops the workqueue being left to run in parallel with close or a
few other operations. This causes double unmaps and the like.
See kerneloops.org #1041230 for an example
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sizing the buffer based on block size is incorrect, leading
to a potential buffer over-run on 4K block size file systems
(because the metadata block size is always 8K). This bug
doesn't seem have triggered because 4K block size file systems
are not default, and also because metadata blocks after
compression tend to be less than 4K.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
Fix warn_on triggered by mounting a fsfuzzer corrupted file system, where
the root inode has been corrupted.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
Reported-by: Steve Grubb <sgrubb@redhat.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] use max load in conservative governor
[CPUFREQ] fix a lockdep warning
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
gianfar: Fix potential oops during OF address translation
fsl_pq_mdio: Fix kernel oops during OF address translation
tcp: bind() fix when many ports are bound
rdma: potential ERR_PTR dereference
rtnetlink: potential ERR_PTR dereference
net: ipv6 bind to device issue
ipv6: allow to send packet after receiving ICMPv6 Too Big message with MTU field less than IPV6_MIN_MTU
drivers/net/usb: Add new driver ipheth
cxgb3: fix linkup issue
X25 fix dead unaccepted sockets
KS8851: NULL pointer dereference if list is empty
net: 3c574_cs fix stats.tx_bytes counter
xfrm6: ensure to use the same dev when building a bundle
can: Fix possible NULL pointer dereference in ems_usb.c
net: Fix an RCU warning in dev_pick_tx()
ipv6: Fix tcp_v6_send_response transport header setting.
bridge: add a missing ntohs()
8139too: Fix a typo in the function name.
mac80211: pass HT changes to driver when off channel
mac80211: remove bogus TX agg state assignment
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Ensure we re-enable devices on resume
x86/PCI: parse additional host bridge window resource types
PCI: revert broken device warning
PCI aerdrv: use correct bit defines and add 2ms delay to aer_root_reset
x86/PCI: ignore Consumer/Producer bit in ACPI window descriptions
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
eeepc-laptop: add missing sparse_keymap_free
eeepc-wmi: Build fix
asus: don't modify bluetooth/wlan on boot
dell-wmi: Fix memory leak
eeepc-wmi: add backlight support
eeepc-wmi: use a platform device as parent device of all sub-devices
eeepc-wmi: add an eeepc_wmi context structure
The unpack routine fails to handle the decompress_method() returning
unrecognised decompressor (compress_name == NULL). This results in the
routine looping eventually oopsing on an out of bounds memory access.
Note this bug is usually hidden, only triggering on trailing junk after
one or more correct compressed blocks. The case of the compressed archive
being complete junk is (by accident?) caught by the if (state != Reset)
check because state is initialised to Start, but not updated due to the
decompressor not having been called. Obviously if the junk is trailing a
correctly decompressed buffer, state == Reset from the previous call to
the decompressor.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The follow_page() function can potentially return -EFAULT so I added
checks for this.
Also I silenced an uninitialized variable warning on my version of gcc
(version 4.3.2).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Izik Eidus <ieidus@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a standalone version of VMware Balloon driver. Ballooning is a
technique that allows hypervisor dynamically limit the amount of memory
available to the guest (with guest cooperation). In the overcommit
scenario, when hypervisor set detects that it needs to shuffle some
memory, it instructs the driver to allocate certain number of pages, and
the underlying memory gets returned to the hypervisor. Later hypervisor
may return memory to the guest by reattaching memory to the pageframes and
instructing the driver to "deflate" balloon.
We are submitting a standalone driver because KVM maintainer (Avi Kivity)
expressed opinion (rightly) that our transport does not fit well into
virtqueue paradigm and thus it does not make much sense to integrate with
virtio.
There were also some concerns whether current ballooning technique is the
right thing. If there appears a better framework to achieve this we are
prepared to evaluate and switch to using it, but in the meantime we'd like
to get this driver upstream.
We want to get the driver accepted in distributions so that users do not
have to deal with an out-of-tree module and many distributions have
"upstream first" requirement.
The driver has been shipping for a number of years and users running on
VMware platform will have it installed as part of VMware Tools even if it
will not come from a distribution, thus there should not be additional
risk in pulling the driver into mainline. The driver will only activate
if host is VMware so everyone else should not be affected at all.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Chan