We need to use the nosync version of disable_irq so that we don't hang in
the IRQ handler as we don't ACK the interrupt until later. This used to
work regardless, but at some point, the IRQ behavior changed. Not sure
when exactly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Keycodes in 248 - 254 range were reserved for special needs (scrolling)
of atkbd driver. Now that the driver has been switched to use unsigned
short keycodes instead of unsigned char we can release this range back
into pull. We keep code 255 (ATKBD_KEY_NULL) reserved since users may
have been using it to silence keys they do not care about since atkbd
silently drops scancodes mapped to this keycode.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the Kconfig entry for the sh_keysc driver to
enable build on SH-Mobile ARM platforms.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add mode 6 support to the sh_keysc driver. Also update the KYOUTDR mask
value to include all 16 register bits.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use bitmaps instead of using 32-bit integers to keep track of the key
states. With this change in place the driver supports key pads with
more than 32 keys.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the sh_keysc driver to factor out the register access functions
sh_keysc_read(), sh_keysc_write() together with sh_keysc_level_mode().
This makes the code a bit easier to follow.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Provided that now keyboards on these devices are fully supported by
generic GPIO based matrix keypad driver, mark these hardcoded and
difficult to maintain drivers as deprecated.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now gpio-keys input driver exports 4 new attributes to userland through
sysfs:
/sys/devices/platform/gpio-keys/keys [ro]
/sys/devices/platform/gpio-keys/switches [ro]
/sys/devices/platform/gpio-keys/disabled_keys [rw]
/sys/devices/platform/gpio-keys/disables_switches [rw]
With these attributes, userland program can read which keys and
switches can be disabled and then disable/enable them as needed.
Keys and switches are exported as stringified bitmap of codes
(keycodes or switch codes). For example keys 15, 89, 100, 101,
102 are exported as: '15,89,100-102'.
Description of the attributes:
keys - bitmap of keys which can be disabled
switches - bitmap of switches which can be disabled
disabled_keys - bitmap of currently disabled keys
(bit 1 means disabled, 0 enabled)
disabled_switches - bitmap of currently disabled switches
(bit 1 means disabled, 0 enabled)
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The IMX family of Application Processors is shipped with a Keypad Port
supported by this driver.
The peripheral can control up to an 8x8 matrix key pad where all the
scanning is done via software. The hardware provides two interrupts:
one for key presses (KDI) and one for all key releases (KRI). There is
also a simple circuit for glitch reduction (said for synchronization)
made by two series of 3 D-latches clocked by the keypad-clock that
stabilize the interrupts sources. KDI and KRI are fired only if the
respective conditions are maintained for at last 4 keypad-clock cycle.
Since those circuits are poor for a correct debounce process (the
keypad-clock frequency is 32K and bounces longer than 94us are not
masked) the driver, when an interrupt arrives, samples the matrix
with a period of 10ms until the readins are stable for
IMX_KEYPAD_SCANS_FOR_STABILITY times (currently set at 3). After
getting stable result appropriate events are sent through the input
stack.
If some keys are maintained pressed, the driver continues to scan
the matrix with a longer period (60ms) to catch possible multiple
key presses without overloading the cpu. This process ends when all
keys are released.
This driver is tested to build in kernel or as a module and follow
the specification of Freescale Application processors:
i.MX25 i.MX27 i.MX31 i.MX35 i.MX51 especially tested on i.MX31.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Mode 4 and Mode 5 support to the SH_KEYSC driver. These modes allow
slightly larger key pad matrixes.
While at it, make use of resource_size().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ADP5587 is quite similar to the ADP5588 but features a greater I/O
voltage range and lacks the Dual Light Sensor Interface. This new part
is also supported by this driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use struct matrix_keymap_data to supply the keymap from the platform code
and matrix_keypad_build_keymap() to initialize the keymap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The id_table field of the struct i2c_driver is defined as constant
in <linux/i2c.h> so it makes sense to mark the initialization data also
constant.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
dev_err(), dev_warn() and dev_dbg() ensure consistency in driver messages.
Also switch to using bool where appropriate and fix some formatting issues.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a function pointer in the platform data of the DaVinci Keyscan driver
called device_enable, in order to perform board specific actions when
the device is initialized, like setup the PINMUX configuration.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to first unregister input device and only then cancel event work
since events can arrive (and cause event work to get scheduled again)
until input_unregister_device() returns.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs_remove_group() waits for sysfs attributes to be removed, therefore
we do not need to worry about driver-specific attributes being accessed
after driver has been detached from the device. In fact, attempts to take
serio->drv_mutex in attribute methods may lead to the following deadlock:
sysfs_read_file()
fill_read_buffer()
sysfs_get_active_two()
psmouse_attr_show_helper()
serio_pin_driver()
serio_disconnect_driver()
mutex_lock(&serio->drv_mutex);
<--------> mutex_lock(&serio_drv_mutex);
psmouse_disconnect()
sysfs_remove_group(... psmouse_attr_group);
....
sysfs_deactivate();
wait_for_completion();
Fix this by removing calls to serio_[un]pin_driver() and functions themselves
and using driver-private mutexes to serialize access to attribute's set()
methods that may change device state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On certain boards not all GPIOs may be used as wakeup sources, in which
case some of enable_irq_wake() calls will fail. On resume calling
disable_irq_wake() will warn about unbalanced IRQ wake disable.
Solve this by checking whether enable_irq_wake() succeeded or not and
no not call disable_irq_wake() for these GPIOs/IRQs that have not been
enabled.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of doing full-blown reset while suspending or shutting down
the box use lighter form of reset that should take less time.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver was merged before the ep93xx core support was added
for the keypad clock and acquiring/releasing the necessary gpio's.
Now that the proper support is in the ep93xx core this driver
needs to be updated to work correctly.
Summary of changes:
1) Remove some unused members from the platform data.
2) Remove the custom KEY macro and use the ones available in
<linux/input/matrix_keypad.h>
3) Remove the keypad_{readl/writel} macros and just use
__raw_{readl/writel} directly.
4) Update the clk_set_rate() call to work with the core support.
5) Cleanup the probe routine and remove some unneeded messages.
6) Use the ep93xx core functions to acquire and release the gpio's.
7) Fix the clk_get() call to get the keypad clock.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to read and report gpio state when we bind the driver to the
device and upon resume so that userspace has correct state of the
switches (and keys but they are less important since, even if they
are happened to be pressed, we'd expect them to be released fairly
soon).
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch moves the KEYSC header file from the
SuperH specific asm directory to a place where
it can be shared by multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the code that deals with setting up each individual button out into
a new function to reduce the indentation and allow us to common up some
of the error recovery code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio keys driver should be using <linux/gpio.h> instead
of <asm/gpio.h>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_keys driver is binding to a platform device but using pr_err()
to report errors. Change to using dev_err() so that all messages are
prefixed by the device name.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is nothing that disallows gpio-keys to share it's IRQ line
w/ other drivers. Make it use IRQF_SHARED in request_irq().
An example of other driver with which I'd like to share IRQ line
for GPIO buttons is ledtrig-gpio.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
OQO 01+ multimedia keys produce 6x on press, e0 6x upon release.
As a result, Linux thinks that another key has been pressed (or is
repeating), when it is actually a release of the same key. Mangle the
release scancode when running on OQO so that driver recognizes it as
such.
Since the device does not have external PS/2 ports mangling is safe
since there is no chance that an external keyboard is connected.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some machines share same key list for volume up/down release key quirks,
use only one key list.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to postpone restoring LED state and typematic settings until
keyboard is finished reconnecting upon resume. Normally driver core
and PM infrastructure takes care of proper ordering and dependencies,
but or case actual reconnect is done asynchronously from kseriod.
So while driver core thinks that keyboard was resumed and it is time
to let input core run it's resume handlers in reality keyboard is not
ready yet. The solution is to keep rescheduling work that adjusts LED
and rate settings until keyboard is fully enabled.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver enables keypad support on DaVinci platforms. DM365 is the
only platform that uses this driver at the moment.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- no spaces between function name and opening parenthesis
- switch statements were indented too much
This makes checkpatch (and me) happy.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix breakage caused by commit 9605fb48e1
While the input core indeed takes care of restoring led state and
typematic settings upon resume the driver still need to initialize
them properly when registering a new device
Reported-and-tested-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
This version only supports individual cells (no slide support yet).
The code has been tested on proprietary development ARM board, but
should work fine on other machines.
Signed-off-by: Raphael Derosso Pereira <raphaelpereira@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert max7359 driver to use IRQ threading instead of using
workqueue.
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Maxim MAX7359 is a I2C interfaced key switch controller which
provides microprocessors with management of up to 64 key switches.
This patch adds support for the MAX7359 key switch controller.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that input core takes care of restoring state of input devices
upon resume we don't need to do anything special here.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Mike Frysinger