Moved pseries, iseries, chrp, prep, maple and pasemi into their respective
arch/powerpc/platform/*/Kconfig files out of arch/powerpc/Kconfig
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rework how multi-function PCI devices are identified and traversed.
This fixes a bug with multi-function recovery on Power4 that was
introduced by a recent Power4 EEH patch.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After requesting a state change, verify that the state change
actually ocurred, and the system ends up in the expected state.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The EEH event notification system passes around data that is
not needed or at least, not used properly. Stop passing this
data; get it in a more reliable fashion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Modify routine that returns PCI slot status to wait for slot status
to become available. This is needed, as slots that are in some remote
card cage may go offline for extended periods of time. New users for
this routine in following patches.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some firmware versions will return a slot reset state of "1"
when a slot is EEH frozen. Recognize this as a state that can be
handled.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the second or higher function of a multi-function device fails
to recover, this failure is not reported upwards. Fix this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If a device driver does not have native PCI error recovery,
a hotplug error recovery will be attemped. In this case,
the device driver will not report back whether its healthy
or not; simply assume that it is.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide support for the new ibm,get-config-addr-info2 RTAS token,
whenever it is actually available.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers will attempt to perform a lot of mmio even after
an EEH event was detected. This is especially the case for fast cpu's
and PCI-E slots. Be a bit more lenient in allowing this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are multiple code patchs tht resuls in a "permanent
failure"; when examining rare events, it can be hard to see
which was taken. This patch adds printk's to assist.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the order in which pci error state is examined;
the "capabilites" is not valid if "reset state" is 5.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I noticed that we execute hcalls before cpu feature code has run (eg
for setting up the bolted kernel region). This means that we may be
executing code that is not appropriate for the processor we have.
Create an unconditional branch that we nop out all the time to fix this.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
kexec invokes plpar_hcall hypervisor call in real mode. plpar_hcall
refers to per cpu variables for accounting hypervisor statistics.
These variables may not be in the RMO region, so accesses to them
in real mode may result in a data storage exception.
This fixes this problem by using a new plpar_hcall_raw function which
does not update the hypervisor call statistics. Thanks to Anton for
suggesting this idea.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This will allow us to build without PCI easier.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During power outages, the UPS notifies the system for a shutdown.
In the current setup, it isn't possible to poweron when power is
restored. This patch fixes the issue by calling the right
ibm,power-off-ups token during such events. It also adds a sysfs
interface so userspace can specify whether or not to power on when
power is restored.
Signed-off-by: Manish Ahuja <ahuja@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My "cleanup" patch (dce623e082) had a cut
and paste error for the !CONFIG_KEXEC case. Fifty lashes for me.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move all the pseries kexec code into one file, platforms/pseries/kexec.c
Provide helpers for setting up ppc_md.kexec_cpu_down, so that we don't
have to have #ifdef CONFIG_KEXEC in setup.c
Move the initialisation of the ppc_md kexec callbacks into an init routine.
This is well and truly early enough to cause no change in behaviour, we
can't kexec until userspace has given us a kernel to kexec into.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move some extern declarations from setup.c into the new pseries.h.
While we're at it, provide dummy implementations for !SMP, to avoid
cluttering the C file with more #ifdefs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Following the example of platforms/pasemi, consolidate a couple of
tiny header files in platforms/pseries into pseries.h.
This gives us a convenient place to put things that need to be
available to the platform code, but not public. And hopefully will
help people resist the temptation of sticking externs in C files.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
H_BULK_REMOVE lets us remove 4 entries from the MMU hash table with one
hypervisor call. This uses it in pSeries_lpar_hpte_invalidate so we
can tear down mappings with fewer hypervisor calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that EEH is improperly enabled for some Power4 systems.
On these systems, the ibm,set-eeh-option returns a value of success
even when EEH is not supported on the given node. Thus, an explicit
check for support is required.
During boot, on power4, without this patch, one sees messages
similar to:
EEH: event on unsupported device, rc=0 dn=/pci@400000000110/IBM,sp@1
EEH: event on unsupported device, rc=0 dn=/pci@400000000110/pci@2
EEH: event on unsupported device, rc=0 dn=/pci@400000000110/pci@2,2
etc.
The patch makes these go away.
Without this patch, EEH recovery does seem to work correctly for
at least some devices (I tested ethernet e1000), but fails to
recover others (the Emulex LightPulse LPFC, most notably).
Off the top of my head, I don't remember why some devices are
affected, but not others.
The PAPR indicates that the correct way to test for EEH is as
done in this patch; its not clear to me if this was in the PAPR
all along, or recently added; if it was there all along, its not
clear to me why this hadn't been fixed long ago. I suspect only
certain firmware levels are affected.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Note all POWER3/POWER4 systems where fixup_winbond_82c105 will run.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that the iommu table address is never stored, and thus
never found, on non-lpar systems. Thus, for example, during boot:
<7>[ 93.067916] PCI: Scanning bus 0001:41
<7>[ 93.068542] PCI: Found 0001:41:01.0 [8086/100f] 000200 00
<7>[ 93.068550] PCI: Calling quirk c0000000007822e0 for 0001:41:01.0
<7>[ 93.069815] PCI: Fixups for bus 0001:41
<4>[ 93.070167] iommu: Device 0001:41:01.0 has no iommu table
<7>[ 93.070251] PCI: Bus scan for 0001:41 returning with max=41
No iommu table? How can that be? Well, circa line 471 of
arch/powerpc/platforms/pseries/iommu.c we see the code:
while (dn && PCI_DN(dn) && PCI_DN(dn)->iommu_table == NULL)
dn = dn->parent;
and a few lines later is the surprising print statement about
the missing table. Seems that this loop ran unto the end, never
once finding a non-null PCI_DN(dn)->iommu_table.
The problem can be found a few lines earlier: it sems that the
value of PCI_DN(dn)->iommu_table is never ever set. Thus, the
patch sets it.
The patch was tested on a Power4 system running in full system
partition mode, which is where I saw the problem. It works; I've
not done any wider testing. Had a brief discussion on this on irc.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There were a few issues with the HCALL_STATS code:
- PURR cpu feature checks were backwards
- We iterated one entry off the end of the hcall_stats array
- Remove dead update_hcall_stats() function prototype
I noticed one thing while debugging, and that is we call H_ENTER (to set
up the MMU hashtable in early init) before we have done the cpu fixups.
This means we will execute the PURR SPR reads even on a CPU that isnt
capable of it. I wonder if we can move the CPU feature fixups earlier.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It looks to me like we are corrupting r12 in the hcall9 function.
Although we have r0 free we cant use offsets against it, so save
away r12 in there instead. r12 holds the ninth return value from
the hypervisor call, so without this fix, the caller will see the
wrong value for the ninth element in the array that gets the return
values.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can use default_server when masking an interrupt vector.
get_irq_server() assumes a virtual irq, so badness may happen if we
give it a real one.
Signed-off-by: Michal Ostrowski <mostrows@watson.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pSeries_probe can decide that we are a pseries but then fail to
initialise the MMU. If an rtas node doesnt exist, we continually fall
out of pSeries_probe_hypertas early and never get to the MMU init code.
While pseries without RTAS is an illegal combination, the way we
currently fail is a pain to track down, and can happen if your flattened
device tree code has issues (like mine did :).
With the following patch we init the MMU, come up and print some
warnings about RTAS not existing, instead of looping on 0x400 exceptions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We find the OF root the line before, we may as well use it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If one attempts to create a device driver recovery sequence that
does not depend on a hard reset of the device, but simply just
attempts to resume processing, then one discovers that the
recovery sequence implemented on powerpc is not quite right.
This patch fixes this up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Purely cosmetic. Change pSeries to pseries inline with other parts of the
kernel, and fix an overly long line.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To support cpu hotplug on pseries we require two RTAS tokens. The cpu
hotplug machinery should only be wired up if these tokens are found in
the device tree.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the rest of the hotplug cpu code from platforms/pseries/smp.c into
platforms/pseries/hotplug-cpu.c.
Wire up the smp_ops callbacks and the notifier in the hotplug cpu initcall,
rather than in smp_init_pseries(). No change in behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.c,
this allows rtas_stop_self() to be static so remove the prototype.
Wire up pSeries_mach_cpu_die() in the initcall, rather than statically
in setup.c, the initcall will still run prior to the cpu hotplug code
being callable, so there should be no change in behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As the first step in consolidating the pseries hotplug cpu code,
create platforms/pseries/hotplug-cpu.c and move rtas_stop_self()
into it. Do the rtas token initialisation in a new initcall, rather
than rtas_initialize().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows any secondary CPU thread also to become boot cpu for
POWER5. The patch is required to solve kdump boot issue when the
kdump kernel is booted with parameter "maxcpus=1". XICS init code
tries to match the current boot cpu id with "reg" property in each CPU
node in the device tree. But CPU node is created only for primary
thread CPU ids and "reg" property only reflects primary CPU ids. So
when a kernel is booted on a secondary cpu thread above condition will
never meet and the default distribution server is left as zero. This
leads to route the interrupts to CPU 0, but which is not online at
this time.
We use ibm,ppc-interrupt-server#s to check for both primary and
secondary CPU ids. Accordingly default distribution server value is
initialized from "ibm,ppc-interrupt-gserver#s" property. We loop
through ibm,ppc-interrupt-gserver#s property to find the global
distribution server from the last entry that matches with boot cpuid.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Per email discussion, it appears that rtas_stop_self()
and pSeries_mach_cpu_die() should not be compiled if
CONFIG_HOTPLUG_CPU is not defined. This patch adds
#ifdefs around these bits of code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.
Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).
It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala