The linux bitset operators (test_bit, set_bit etc) work on arrays of "unsigned
long". dm-log uses such bitsets but treats them as arrays of uint32_t, only
allocating and zeroing a multiple of 4 bytes (as 'clean_bits' is a uint32_t).
The patch below fixes this problem.
The problem is specific to 64-bit big endian machines such as s390x or ppc-64
and can prevent pvmove terminating.
In the simplest case, if "region_count" were (say) 30, then
bitset_size (below) would be 4 and bitset_uint32_count would be 1.
Thus the memory for this butset, after allocation and zeroing would
be
0 0 0 0 X X X X
On a bigendian 64bit machine, bit 0 for this bitset is in the 8th
byte! (and every bit that dm-log would use would be in the X area).
0 0 0 0 X X X X
^
here
which hasn't been cleared properly.
As the dm-raid1 code only syncs and counts regions which have a 0 in the
'sync_bits' bitset, and only finishes when it has counted high enough, a large
number of 1's among those 'X's will cause the sync to not complete.
It is worth noting that the code uses the same bitsets for in-memory and
on-disk logs. As these bitsets are host-endian and host-sized, this means
that they cannot safely be moved between computers with
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some circumstances the LIST_VERSIONS output is truncated because the size
calculation forgets about a 'uint32_t' in each structure - but the inclusion
of the whole of ALIGN_MASK frequently compensates for the omission.
This is a quick workaround to use an upper bound. (The code ought to be fixed
to supply the actual size.)
Running 'dmsetup targets' may demonstrate the problem: when I run it, the last
line comes out as 'erro' instead of 'error'. Consequently, 'lvcreate --type
error' doesn't work.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An error path in table_load() forgets to release a table that won't now be
referenced.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver only appears on IA32 & EM64T boxes.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
scsi_get_command() attempts to write into a structure that may not have
been successfully allocated. Move this write inside the if statement that
ensures we won't panic the kernel with a NULL pointer dereference.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/cpufreq/cpufreq.c: In function `cpufreq_remove_dev':
drivers/cpufreq/cpufreq.c:696: warning: unused variable `cpu_sys_dev'
Signed-off-by: Grant Coady <gcoady@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Wayne E. Harlan
"[1.] One line summary of the problem:
When the kernel option "vga=1" is used, additional tty's (alt+control+Fx
with x=2,3,4,5, etc) do not provide the full 50 lines of output. The first
one does have 50 lines, however.
[2.] Full description of the problem/report:
These addtitional tty's show only 39 lines plus the top pixel of the 40-th
line. The remaining lines are black and not shown. Kernel version
2.6.13.4 does not show this problem."
This bug is caused by using a stale font height value on vgacon_init.
Booting with vga=1 gives an 80x50 screen with an 8x8 font. Somewhere
during the initialization, the font was changed to 8x9 and the first
vc was correctly resized to 80x44. However, the rest of the vc's were
not allocated yet, and when they were subsequently initialized, they
still used a font height of 8 (instead of 9) causing the mentioned bug.
Fix by saving the new font height to vga_video_font_height.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The shift value (amount to shift the bitmap so first pixel starts at
origin(0,0)) is incorrect. This causes corrupted characters or a kernel crash
if fontwidth is not divisible by 8 at 270 degrees, or fontheight not divisible
by 8 at 180 degrees.
Report and part of the fix contributed by Knut Petersen.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's strange enough to be looking out for anonymous pages in VM_UNPAGED areas,
let's not insert the ZERO_PAGE there - though whether it would matter will
depend on what we decide about ZERO_PAGE refcounting.
But whereas do_anonymous_page may (exceptionally) be called on a VM_UNPAGED
area, do_no_page should never be: just BUG_ON.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/net/dgrs.c: In function `dgrs_init_module':
drivers/net/dgrs.c:1598: `dgrs_pci_driver' undeclared (first use in this function)
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an OOPS is CinergyT2 driver when registering IR remote
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kseriod and kgameportd used to process all pending events before
checking for freeze condition. This may cause swsusp to time out
while stopping tasks when resuming. Switch to process events one
by one to check freeze status more often.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If thread that submitted FF request gets interrupted somehow it
will release request structure and ioctl handler will work with
freed memory. TO prevent that from happening switch to using
wait_for_completion instead of wait_for_completion_interruptible.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Try to save battery power by disabling wifi and bluetooth on suspend.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also fix a potential issue with some notebooks:
The current code assumes the response to bios_wifi_get_default_setting is
either 1 (disabled) or 3 (enabled), or wifi isn't supported. The BIOS
response appears to be a bit field w/ 0x1 indicating hardware presence, 0x2
indicating actiation status, and the other 6 bits being unknown/reserved --
with the patch, these 6 bits are ignored.
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On x86_64:
{standard input}:233: Error: suffix or operands invalid for `push'
{standard input}:233: Error: suffix or operands invalid for `pop'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A driver for laptop buttons using an x86 BIOS interface that is
apparently used on quite a few laptops and seems to be originating
from Wistron.
This driver currently "knows" only about Fujitsu-Siemens Amilo Pro V2000
(i.e. it can detect the laptop using DMI and it contains the
keycode->key meaning mapping for this laptop) and Xeron SonicPro X 155G
(probably can't be reliably autodetected, requires a module parameter),
adding other laptops should be easy.
In addition to reporting button presses to the input layer the driver
also allows enabling/disabling the embedded wireless NIC (using the
"Wifi" button); this is done using the same BIOS interface, so it seems
only logical to keep the implementation together. Any flexibility
possibly gained by allowing users to remap the function of the "Wifi"
button is IMHO not worth it when weighted against the necessity to run
an user-space daemon to convert button presses to wifi state changes.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Changing led state is pretty slow operation; when there are multiple
requests coming at a high rate they may interfere with normal typing.
Try optimize (skip) changing hardware state when multiple requests
are coming back-to-back.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
flagged_taskfile() is called from execute_drive_cmd()
(the only user) only if args->tf_out_flags.all != 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the spinlock was removed from sa1100_start_tx(), the "flags"
variable becomes redundant. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The receiver status register reports latched error conditions, which
must be cleared by writing to it. However, the data register reports
unlatched conditions which are associated with the current character.
Use the data register to interpret error status rather than the RSR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make sure that userspace passes in enough data when sending a MAD. We
always copy at least sizeof (struct ib_user_mad) + IB_MGMT_RMPP_HDR
bytes from userspace, so anything less is definitely invalid. Also,
if the length is less than this limit, it's possible for the second
copy_from_user() to get a negative length and trigger a BUG().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The following patch fixes a crash caused by attempting to bounce buffer
when an IDE CD-ROM is used on a machine with an IO-MMU. [At least, this
patch fixes things so I can use my IDE CD-ROM behind an ns87415 on a
HP PA-RISC workstation.]
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Calculation of QP capabilities still isn't exactly right in mthca:
max_send_sge/max_recv_sge fields returned in create_qp can exceed the
handware supported limits.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
From: Amit Gud <amitg@calsoftinc.com>
Patch follows from the suggestions by AC and Felipe W Damasio for fixing the
return codes from IDE drivers.
[ bart: fix coding style while at it ]
Signed-off-by: Amit Gud <gud@eth.net>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fixes an oops in sbp2util_find_command_for_SCpnt after sbp2scsi_abort:
https://bugzilla.novell.com/show_bug.cgi?id=113734
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
(cherry picked from 7945619794 commit)
From: Thibaut VARENE <T-Bone@parisc-linux.org>
Cleaning up the hwif without knowing its previous state in pmac.c is a big
and potentially dangerous job, and there seems to be no generic code interface
that would provide either a way to properly release an hwif or to clean it up.
Fixes OOPS for empty PMAC interface and add-on PCI controller.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These drivers do not compile on big endian systems, and parisc
is big endian. Also mark some as broken on m68k as well.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
From: Hanna Linder <hannal@us.ibm.com>
The dev returned from pci_find_device() was not used so it can be
replaced with pci_dev_present(). Compile tested.
Signed-off-by: Hanna Linder <hannal@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mention PA-RISC in NS87415 help. PA-RISC [BCJ]xxx0 workstations come with
NS87415 integrated for their CD-ROM drives.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Depend on GSC, not PARISC. Machines without GSC don't have a MUX.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The structure ide_driver_t have a .owner field which is a duplicate
of .gendriver.owner field (.gen_driver is a struct device_driver).
This patch removes ide_driver_t's owner field.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alasdair G Kergon