According to http://www.ip-phone-forum.de/showthread.php?t=225313 this
HW works. Thanks to Lars Immisch for pointing to this thread.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
We test both "!skb_out" and "skb_out" here which is duplicative and
causes a static checker warning. I considered that the intent might
have been to test "skb_in" but that's a valid pointer here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MISDN_CTRL_RX_OFF is a meachanism to discard RX data in the driver if
the data is not needed by the application. It can be used when playing
mesages, but not recording or with unidirectional protocols.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MISDN_CTRL_FILL_EMPTY is a meachanism to send a fixed value (normally silence)
as long no data from upper layers is available. It can be used when recording
voice messages or with unidirectional protocols.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the FIFO of the card is small, many short messages are queued up to
the upper layers and the userspace. This change allows the applications
to set a minimum datalen they want from the drivers.
Create a common control function to avoid code duplication in each
driver.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did allways allocate maxsize buffers, but for transparent data we know
the actual size.
Use a common function to calculate size and detect overflows.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here was a off by one in the activation/deactivation.
The additional activation in open_bchannel() did hide
it, but only if you do not try to use B2.
Signed-off-by: Martin Bachem <info@colognechip.com>
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we detect the latest hardware revision we should use the bigger fifo
to avoid TX underruns and have less interrupts.
TX underruns should be logged as warning.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is better to send a confirm for transparent data early as possible
to avoid TX underuns.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a channel was closed after it was deactivated it could happen that
something was not proper resetted. The test if a channel is still activ
was wrong, so remove it and always do the cleanup.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If Kernel CAPI is compiled without CONFIG_ISDN_CAPI_MIDDLEWARE,
the structure retrieved via capincci_find() is never actually
used, so don't compile that function in that case.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up some of the readibility deterioration caused by the recent
whitespace coding style cleanup.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various functions in the Gigaset driver were using different
conventions for the meaning of their int return values.
Align them to the usual negative error numbers convention.
Inspired-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions clear_at_state and free_strings did the same thing;
drop one of them, keeping the more descriptive name.
Drop a redundant call.
Rename function dealloc_at_states to dealloc_temp_at_states
to clarify its purpose.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up some of the readibility deterioration caused by the recent
whitespace coding style cleanup.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
An out-of-place "OK" response to the "AT+GMR" (get firmware version)
command turns out to be, more often than not, a delayed response to
a previous command rather than an actual error, so continue waiting
for the version number in that case.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DISCONNECT_B3_IND was synthesized because of a DISCONNECT_REQ
with existing logical connections, the connection state wasn't
updated accordingly. Also the emitted DISCONNECT_B3_IND message
wasn't included in the debug log as requested.
This patch fixes both of these issues.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a global ratelimit for CAPI message dumps to protect
against possible log flood.
Drop the ratelimit for ignored messages which is now covered by the
global one.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With multiple cards is hard to figure out which port caused trouble
int the layer2 routines (e.g. got a timeout).
Now we have the informations in the log output.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer3 and the activation delay timer need to be independent.
If timer3 fires do not reqest power up we have to send only INFO 0.
Now layer1 pass TBR3 again.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certification test it is very useful to change the layer1
timer3 value on runtime.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be full preemptiv safe, we cannot handle a L2 timeout in the timer
context itself, we should do all actions via the D-channel thread.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some configs it was still not possible to unload the driver,
because the module use count was srewed up.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tei manager reports current layer 1 state on creation.
On state change it reports it to the socket interface.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the custom DIVA_{INIT,EXIT}_FUNCTION defines and use
the standard __init,__exit markup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmentation is usefull if multiple devices are connected to an E1
interface. Each fragment will have a subset of the available timeslots.
These devices require a cascde connection or a multiplexer.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
LEDs will show RED if layer 1 is disabled or fails.
LEDs will show GREEN if layer 1 is active.
LEDs will blink if traffic on D-channel.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have the flag for L1 active, so we should use it.
L2 will be solved in a later patch.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmitted audio data was interrupted if a bridge was enabled or disabled.
Now transmission seamlessly continues during that action.
Fix in hfcmulti.ko
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsp_spl_jiffies need to be the same datatype as jiffies (which is ulong).
If not, on 64 bit systems it will fallback to schedule the DSP every jiffie
tic as soon jiffies become > 2^32.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DTMF debug is set and tresh goes under 100, the printk will cause
a division by zero.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the hardware bridging/conference (2-n parties) was selected,
but still pure software bridging/conference was used.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug (was introduced by a cut & paste error)
in cases when dsp->conf was NULL.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the code for getting an number from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "ISDN: i4l, remove cvs crap" removed definition of
isdn_tty_revision, but there is still a user. So this causes linking
errors. This was hidden from my radar because the variable was not
declared in any header. Instead isdn_common.c declares it locally.
So remove this variable also from isdn_common.c, because there is
really no way to find out the version. Git commit or tag is...
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes a bunch of duplicated code which does the same as
tty_port_block_til_ready does.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add there .carrier_raised. It is taken from current block_til_ready.
We will need tty_port->ops->carrier_raised for
tty_port_block_til_ready helper.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code does almost the same, so there we can leverage the helper's
code. The only difference is locking. The helper protects counts by a
spinlock. This never hurts and should be added to other code parts
too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some functions we use tty_port much. So let us have a local pointer
to that variable instead of having info->port all over the code.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No recounting this time, just a plain switch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use tty_port->flags now. Other members will follow.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huh, this was a mess.
* Remove the 5 indent levels by just returning from isdn_tty_try_read
when the conditions there are not satisfied.
* Use 'continue' in loop in isdn_tty_readmodem to save 2 levels.
* Chain 'if's in isdn_tty_modem_escape.
* Use 'continue' in loop in isdn_tty_carrier_timeout to save 1 level.
Better to look at this patch with -w -b.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module which called allocate_tty_driver is already refcounted by
the TTY layer automatically. And since THIS_MODULE is isdn_tty and it
allocated the tty_driver, there is no need to do the counts in isdn's
tty->ops->open/close.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are the same as TTY ones. So there is no need to redefine them.
Remove ISDN_ASYNC_* and use only ASYNC_*. Except the MAGIC number, of
course.
While we are there, remove also the SERIAL_TYPE flags which are
unused.
Perhaps we should move the ASYNC flags from serial.h to tty.h given
they are used by the tty layer and tty drivers, not only serial?
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I wonder how this survived there during the whole 2.6 series until now
:D.
Callouts are not used for a decade, so let us remove it also from
isdn. This means removal of ISDN_ASYNC_CALLOUT_ACTIVE which is never
raised in info->flags and callout_termios which are never used.
This will help us to get rid of ISDN_ASYNC_* flags and use ASYNC ones
from serial.h. And then we will switch to tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Karsten Keil