The MII registers read/write function blindly busy waits for an
amount of 1000 us (1 ms), then up to 200 ms. These functions are
called from irq disabled context. Depending on the clock management,
it triggers lost ticks events. Since the value is way above the
standard delay required for mii register access, it strangely looks
like a bandaid against posted writes.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5947
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The current orinoco_cs.c can issue the exact same error message for
2 different tests that can fail. Alter them so we can tell which
one of the two failed.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We shouldn't expose the hardware register contents in platform_data.
The only things we allow the user to configure are autoneg, speed, and
duplex. Add specific platform_data fields for these values and remove
the registers configs.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use the common ethtool support functions of the MII library.
Add generic MII ioctl handler.
Add PHY parameter speed/duplex/negotiation initialization and modification.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Modify link up/down handling to use the functions from the MII
library. Note that I track link state using the MII PHY registers
rather than the mv643xx chip's link state registers because I think
it's cleaner to use the MII library code rather than writing local
driver support code. It is also useful to make the actual MII
registers available to the user with maskable kernel printk messages
so the MII registers are being read anyway
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add and use the following functions:
mv643xx_eth_port_enable_tx()
mv643xx_eth_port_enable_rx()
mv643xx_eth_port_disable_tx()
mv643xx_eth_port_disable_rx()
so that ports are enabled/disabled consistently.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tx_ring_skbs is actually a count of tx descriptors currently in use.
Since there may be multiple descriptors per skb, it is not the
same as the number of skbs in the ring.
Also change rx_ring_skbs to rx_desc_count to be consistent.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove duplicated code by having unicast and multicast code use
a common filter table function: eth_port_set_filter_table_entry().
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
mp->port_mac_addr is just a redundant copy of dev->dev_addr, so remove it.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update dev->last_rx on packet receive
This fix corrects errors seen during configuration of the bonding driver.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch eliminates a spinlock recursion bug introduced recently.
Since eth_port_send() is always called with the lock held, we simply
remove the locking inside the function itself.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below is a patch for the Large Receive Offload feature.
Please review and let us know your comments.
LRO algorithm was described in an OLS 2005 presentation, located at
ftp.s2io.com
user: linuxdocs
password: HALdocs
The same ftp site has Programming Manual for Xframe-I ASIC.
LRO feature is supported on Neterion Xframe-I, Xframe-II and
Xframe-Express 10GbE NICs.
Brief description:
The Large Receive Offload(LRO) feature is a stateless offload
that is complementary to TSO feature but on the receive path.
The idea is to combine and collapse(upto 64K maximum) in the
driver, in-sequence TCP packets belonging to the same session.
It is mainly designed to improve 1500 mtu receive performance,
since Jumbo frame performance is already close to 10GbE line
rate. Some performance numbers are attached below.
Implementation details:
1. Handle packet chains from multiple sessions(current default
MAX_LRO_SESSSIONS=32).
2. Examine each packet for eligiblity to aggregate. A packet is
considered eligible if it meets all the below criteria.
a. It is a TCP/IP packet and L2 type is not LLC or SNAP.
b. The packet has no checksum errors(L3 and L4).
c. There are no IP options. The only TCP option supported is timestamps.
d. Search and locate the LRO object corresponding to this
socket and ensure packet is in TCP sequence.
e. It's not a special packet(SYN, FIN, RST, URG, PSH etc. flags are not set).
f. TCP payload is non-zero(It's not a pure ACK).
g. It's not an IP-fragmented packet.
3. If a packet is found eligible, the LRO object is updated with
information such as next sequence number expected, current length
of aggregated packet and so on. If not eligible or max packets
reached, update IP and TCP headers of first packet in the chain
and pass it up to stack.
4. The frag_list in skb structure is used to chain packets into one
large packet.
Kernel changes required: None
Performance results:
Main focus of the initial testing was on 1500 mtu receiver, since this
is a bottleneck not covered by the existing stateless offloads.
There are couple disclaimers about the performance results below:
1. Your mileage will vary!!!! We initially concentrated on couple pci-x
2.0 platforms that are powerful enough to push 10 GbE NIC and do not
have bottlenecks other than cpu%; testing on other platforms is still
in progress. On some lower end systems we are seeing lower gains.
2. Current LRO implementation is still (for the most part) software based,
and therefore performance potential of the feature is far from being realized.
Full hw implementation of LRO is expected in the next version of Xframe ASIC.
Performance delta(with MTU=1500) going from LRO disabled to enabled:
IBM 2-way Xeon (x366) : 3.5 to 7.1 Gbps
2-way Opteron : 4.5 to 6.1 Gbps
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hi,
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hi,
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
One of the if()s contains a call to de_is_running(),
which seems to be safe to replace, but someone with more
knownledge of the code might want to verify this...
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hi,
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There is a problem with fragmented skb in s2io driver version 2.0.9.4
available in 2.6.16-rc1 kernel. The adapter will fail to transmit if
any scatter-gather skb arrives. This patch provides fix for the above
described problem.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On my laptop, the b44 device is created and the carrier state defaults
to ON when created by alloc_etherdev. This means tools like NetworkManager
see the carrier as On and try and bring the device up. The correct thing
to do is mark the carrier as Off when device is created.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Since get_settings() returns a signed int and it gets checked
for < 0 to catch an error, res should be a signed int too.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make phy 0 actually be read, as it is not being right now as we have:
int mii_status = mdio_read(dev, phy, MII_BMSR);
int phyx = phy & 0x1f;
When we should have instead:
int phyx = phy & 0x1f;
int mii_status = mdio_read(dev, phyx, MII_BMSR);
so that when phy, in the end of the (phy = 1; phy <= 32...) loop gets
to 32 phyx gets to 0, i.e. we were reading at 32, when the intended
read was for 0.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On my latest laptop, I've had occasional PHY dead on wakeup from
sleep... the PHY would be totally unresponsive even to toggling the hard
reset line until the machine is powered down... Looking closely at the
code, I found some possible issues in the way we setup the MDIO lines
during suspend along with slight divergences from what Darwin does when
resetting it that may explain the problem. That patch change these and
the problem appear to be gone for me at least... I also fixed an mdelay
-> msleep while I was at it to the pmac feature code that is called
when toggling the PHY reset line since sungem doesn't call it in an
atomic context anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>b
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 1.4.31 and add 2006 copyright.
Skip the last digit when reporting the firmware version.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance the ethtool loopback test with PHY loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround for a hardware interrupt issue. When using INTA,
unmasking of the interrupt and the tag update should be done
separately to avoid some spurious interrupts,
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix TCP/UDP checksum verification. Use status bits in the buffer
descriptor instead of the checksum value to verify rx checksum.
Using the checksum value will be incorrect if the UDP packet has
zero in the UDP checksum field.
Firmware update required for this fix.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some misc. fixes for WoL, 5708 B1, and a typo '=' instead of '=='.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve handshake with bootcode with the following changes:
1. Increase timeout to 100msec and use msleep instead of udelay.
2. Add more error checking for timeouts and errors.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always set up the device to strip incoming VLAN tags when ASF is
enabled. ASF firmware will not parse packets correctly if VLAN tags
are not stripped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*) mark as "EXPERIMENTAL" various items that either aren't very stable or
that are actively crashing the setup of users which don't really need them
(i.e. HIGHMEM and 3-level pagetables on x86 - nobody needs either,
everybody reports "I'm using it and getting trouble").
*) move net/Kconfig near to the rest of network configurations, and
drivers/block/Kconfig near "Block layer" submenu.
*) it's useless and doesn't work well to force NETDEVICES on and to disable
the prompt like it's done. Better remove the attempt, and change that to a
simple "default y if UML".
*) drop the warning about "report problems about HPPFS" - it's redundant
anyway, as that's the usual procedure, and HPPFS users are especially
technical (i.e. they know reporting bugs is _good_).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove page refcount manipulations from cassini driver by using
another field in struct page. Needed for lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
in attempting to not send the "prefetch" patch, we broke the receive code,
this patch fixes that issue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added e1000_mc_addr_list_update
Added e1000_read_reg_io
Added e1000_enable_pciex_master
These are not static functions, that is why we have them declared in the header.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These functions help restore the driver to active configuration when coming out of resume for power management.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Align the prefetches to a dword to help speed them up.
Recycle skb's and early replenish.
Force memory writes to complete before fetching more descriptors.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There are a couple of problems in the DMA setup code for skge.
* In the 64 bit case, it doesn't set the consistent mask.
* In the 32 bit case, the error check is backwards!
It likely will only be visible as a bug on 64 bit platforms.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sizeof() return is not an int, so use max_t to get the types right.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about transmit locking, this solves a possible race
between tx_complete and transmit, that would cause a tx timeout.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to inline quite so many routines, let the compiler
decide
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make sure and rate limit all the error messages that might occur. If a problem
occurs then a few messages are enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Small optimization, if dma addresses are 32 bits, then high
bits are always zero.
Signed-off-by: Stephen Hemminger <shemminger@osdl.or>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Al Viro