- Use inline functions for dma_sync_* instead of macros
- added Kconfig change to make selection for similair SGI boxes easier
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds me as maintainer of the RDC R6040 Fast Ethernet driver.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch skips mac80211 configuration setting during a hardware scan
and replays it afterwards for the iwlwifi drivers.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes the iwlwifi driver to properly support
monitor interfaces after the filter flags change.
The patch is originally created by Johannes Berg for iwl4965. I fixed some
of the comments and created a similar patch for iwl3945.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sizeof(*cmd) is going to give the total size of the data structure that
we allocated, more often than not. But the size of the command to be
_sent_ could be a lot smaller, as it is in the KEY_MATERIAL and
SUBSCRIBE_EVENT commands for example. So swap them round; let the caller
set the _command_ size explicitly in the header, and infer the
maximum response size from the data structure.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't necessarily want to reset the device on a TX timeout. But more
often than not, the real cause is that the firmware has crapped itself,
not just that the network is busy. So submit any harmless command, and
if _that_ times out, then the error handling code will reset the module,
as appropriate.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if it fails, we want to wait a while and try again, with an
ultimate timeout if it the condition persists. So again, just use the
standard command timeout behaviour.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the firmware returns 0x0004, it wants us to try again later. We can
achieve that simply by throwing out the response and letting the command
timeout code kick in.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we don't scribble over the command we sent, then we can retry it when
the firmware responds with 0x0004 (which means -EAGAIN).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a local variable 'resp' which we use for this. So use it,
instead of typing the whole thing.
In preparation for actually using priv->upld_buf for the responses
instead...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the various firmware setup bits into a separate function, which
used to do just boot2 version.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, we go into an endless busy loop trying to enable PS mode when
the command queue is empty, dealing with the error response, and then
trying to enable PS mode again because the command queue is empty.... it
doesn't really save much power.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_send_confirmwake() is a bit ugly but matches the way we confirm
sleep. We'll deal with that whole thing later.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DNLD_RES_RECEIVED is a bit of a misnomer -- we never wait for the result
to be received; it's purely representing the state of the TX path, and
in this case the TX path is definitely busy.
Of course, that means that we don't actually care about DATA_SENT vs.
CMD_SENT either, but that's a can of worms for another day...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 5b8845345e7385d2eb37fac22ba9ab6905988be5 (or, in case the git
workflow is broken and patches get recommitted, the commit entitled
'libertas: rename and re-type bufvirtualaddr to cmdbuf' by dcbw),
introduced a number of bugs where we once had a pointer to a command
_payload_, but now we use the pointer to the command header instead.
The fix isn't wonderfully pretty for now, but it'll get better when we
finish converting all commands so the structures include the header.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we return the channel number in a 'ret' variable where anything
non-zero is later interpreted as an error, that isn't nice. It breaks
WPA, for a start. OLPC trac #5485
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And handle the case where it times out more than once, too, instead of
locking up for ever.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can use the callback_arg for it; that's the way we're heading anyway...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the wakeup into lbs_complete_command(), and leave the other bits
in __lbs_cleanup_and_insert_cmd() which was the only caller now anyway.
There are two remaining direct callers of lbs_cleanup_and_insert_cmd(),
and they are both fine without the wakeup.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We initialise it when we add it to the queue. No need to do it again.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We allocate them all at the same time, at startup. If they go missing,
we have more serious things to worry about, and the resulting oops will
be a perfectly acceptable result.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're about to change semantics, leaving callers of
lbs_prepare_and_send_command() with the old broken priv->cur_cmd_retcode
crap. The existence of the callback command will be the trigger for the
new semantics when handling the response.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call it lbs_submit_command(), remove a bunch of things which can be (or,
in the case of zeroing ->cmdwaitqwoken, already are) done elsewhere.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It wasn't working anyway -- by the time we get into if_usb_disconnect()
the USB core has already stopped us talking to the thing; even if it's
just on unload and the device still exists.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kthread code can't cope with a thread exiting of its own accord and
then someone calling kthread_stop() for it. When the thread detects that
it needs to die, make it wait for kthread_stop() to be called.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes Bug #9414 for b43legacy. This patch is the equivalent of one
submitted earlier for b43.
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above and removes a couple of sparse warnings.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple transmit fifo initialization -
- Assigned equal scheduling priority for all configured FIFO's.
- Modularized transmit traffic interrupt initialization since it is executed in
s2io_card_up and s2io_link. Enable continuous tx interrupt when link is UP
and vice verse.
- Enable transmit interrupts for all configured transmit fifos.
- Fixed typo errors.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixes to enable multiple transmit fifos (upto a maximum of eight).
- Moved single tx_lock from struct s2io_nic to struct fifo_info.
- Moved single ufo_in_band_v structure from struct s2io_nic to struct
fifo_info.
- Assign the respective interrupt number for the transmitting fifo in the
transmit descriptor (TXD).
- Added boundary checks for number of FIFOs enabled and FIFO length.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
set_pci_drvdata() stores a pointer to the adapter,
not the net device.
Add missing softirq blocking in t3_mgmt_tx.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Al Viro