This adds the required platform data and calls to enable
the CRYP/HASH driver.
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The MSP platform data callbacks use the old custom callbacks to
set the state of the pins, switch over to using pinctrl.
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alter the db8500_add_msp_i2s() calls to return a struct
platform_device * pointer, not an integer. We nee the pointer
to obtain a pinctrl handle.
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
UART0 had a hack that enabled its pins on init and put it to
sleep on the exit callback. Replace this with the pinctrl calls
to do the same thing and update the runtime table with the two
apropriate states for runtime/active and idle.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At the beginning of the first patch series I included the custom
ux500 pin control system to make sure I could eventually replace
it with the standard subsystem driver. So now that we've done so,
let's remove it.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Ux500 family to use the pinctrl driver for
configuring pins.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a scratch pin control interface to the Nomadik pinctrl
driver, and defines the pins and groups in the DB8500 ASIC. We
define GPIO ranges to cover the pins exposed. The DB8500 has
more pins than this but we restrict the driver to the pins that
can be controlled from the combined GPIO and pin control hardware
to begin with.
ChangeLog v1->v2:
- Base on the latest pinctrl development from
pinctrl-mergebase-20120418 so we can get rid of legacy
group count mechanism. Also drop the range checks for group
index, this is handled by the core now.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the ST-Ericsson ux500 hash hardware
module. The driver implements support for SHA-1 and SHA-2.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds a driver for the ST-Ericsson ux500 crypto hardware
module. It supports AES, DES and 3DES, the driver implements
support for AES-ECB,CBC and CTR.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the cpuidle driver for the ux500 SoC.
The boards saves 12mA with these states. It is based on the latest
cpuidle consolidation from Robert Lee.
The cpu can go to retention only if the other core is in WFI.
If the other cpu is in WFI and we decoupled the gic from the cores,
then we have the guarantee, it won't be wake up.
It is up to the prcmu firmware to recouple the gic automatically
after the power state mode is selected.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In dbx500 based devices the PRCMU Timer 4 is used as a clocksource
and sched_clock. Here we fetch all necessary addressing information
required for correct PRCMU initialisation from the Device Tree
instead of using hard-coded values.
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now the SCMC911x is correctly enabled in Device Tree, there is no need
to continue registering it from platform code. In fact, if we continue
doing so, the system will throw an error on boot.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To aid in sequential one-by-one Device Tree enablement, we split
cpu-db8500's platform_devs structure into normal platform boot, where
we leave all devices to be added in tact and a DT version where we
will remove the devices as they are DT enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch prevents i2c devices which are not present on the Snowball
low-cost development board from being registered. Devices such as;
tc3589x, bu1780 and lp5521 are present on other supported boards,
but are not located on Snowball.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This platform has been obsoleted and was only available inside of
ST-Ericsson, no users of this code are left in the world. This
deletes the core U5500 support entirely in the same manner as the
obsoleted U8500 silicon was previously deleted.
The cpu_is_u5500() macros that can read out the CPU ID is left
until the next kernel cycle, this makes it possible to merge
deletion of dependent drivers without breakage.
This also has the upside of removing the mailbox driver which was
our only driver that was outside the drivers/* hiearchy, now the
machine directory only handles machines and nothing else.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DB9540 ASIC has bigger PRCMU and PRCMU TCDM memories,
so create a separate mapping table for these.
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the U9540 variant of the U8500 series. This
is an application processor without internal modem. This is the
most basic part with ASIC ID, CPU-related fixes, IRQ list, register
ranges, timer, UART, and L2 cache setup. This is based on a patch
by Michel Jaouen which was rewritten to fit with the latest 3.3
kernel.
ChangeLog v1->v2: deleted the irqs-db9540.h file since we expect to
migrate to using Device Tree for getting the IRQs to devices.
ChangeLog v2->v3: introduced a fixed virtual offset for the ROM
as suggested by Arnd Bergmann.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastien Pasdeloup <sebastien.pasdeloup-nonst@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create devices for the MSP-blocks (MSP0, MSP1, MSP2 and MSP3)
and associate it with the correct clocks in the clock-framework.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add irq domain support to the gpio-nomadik GPIO driver. This
enables its users to support dynamic IRQ assignment, which is
requried by Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This updates the Ux500 pin handling to take much more care when
applying pin settings for different platforms and peripherals.
This is an accumulation of a longer history of updates to the
MOP500 family pin file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement an API to allow a list of pincfgs to be remuxed to active
and sleep modes, for power saving. This is not exported on purpose,
because it is not to be called by drivers directly.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default configuration for a number of I2C and keypad pins was
to pull-up. However on most reference designs the electronics
already contain external pull-ups which means the internal
pull-ups will lower the common resistance and increase power
consumption on these lines, and in some reference designs the
keypad inputs are not used so this will just cause problems. So
remove these pull-ups and add them on demand instead if needed.
Signed-off-by: Magnus Templing <magnus.templing@stericsson.com>
Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To allow for proper initialisation of the SMSC9115 Ethernet chip
and other devices which may be connected to the 'external bus',
Device Tree must first enable and traverse though it. This patch
enables the 'external bus' which will facilitate further
initialisation of its suborantate DT nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This replaces the dynamic device allocator in the ux500 machine
with the common device allocator in the bus code.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A recent change to a Kconfig configuration saw MACH_U8500
remove TPS6105X selection. In doing so Kconfig stopped
selecting REGULATORS, which is still required. This patch
sees UX500_SOC_DB8500 explicitly select it instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wake secondary cpu via resched instead of
"Unknown IPI message 0x1"
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables local timer (AKA: private timer) support for
all u8500 based hardware using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This SSP Controller supports a number of serial communication methods
and as such cannot be registered using of_register_spi_devices.
Instead we register it simply as a primecell device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This provides PL310 Level 2 Cache Controller Device Tree
support for all u8500 based devices.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enables the 3 UARTs found on a u8500 using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the embedded GIC on all u8500 based hardware using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds all devices that are normally present through the
u8500_init_machine function in the device tree as well, which
will duplicate the devices that are visible.
This will not do much by itself because the device from the
device tree are not matched by any device driver until they
are converted as well. The next step is to move over one
device at a time to actually be used from the device tree
instead of the hardcoded device using auxdata to pass the
correct platform_data.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This lets us move over evertything to device tree one by one.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This provides very basic Device Tree support for ST-Ericsson's
low-cost development platform, Snowball. If Device Tree for
ux500 is enabled and the correct board is configured within the
Device Tree blob, the correct *_init_machine() will be called.
This patch is based on some original work completed by:
Niklas Hernaeus <niklas.hernaeus@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mach-ux500/timer.c lacked the inclusion of mach/irqs.h, and thus
failed to compile. Fix it and also remove an unused variable.
Test compiled only.
Reported-by: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergman <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Several platforms incorrectly use __io() for casting to 'void __iomem *'.
This converts all of those uses to use the common IOMEM macro.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-sh@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add support for the new smp_twd runtime registration interface
to the ux500 platforms, and remove the old compile-time support.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The AB9540 variant of the AB8500 is basically close enough
to use the same driver. This adds the new registers and
deviations for this new chip variant.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With bug.h currently living right in linux/kernel.h there
are files that use BUG_ON and friends but are not including
the header explicitly. Fix them up so we can remove the
presence in kernel.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
First rename the config option MACH_U8500 to MACH_MOP500
because that is what it's obviously all about, this has
confused me for the last time. Fix some whitespace in the
process.
Since the machine descriptors for HREFv60 and snowball
are clearly in the file board-mop500.c which only
compiles if MACH_MOP500 (former MACH_U8500) is set,
select this for the board variants and nothing else.
For the MOP500 variants the UIB (user interface board)
is probed using I2C so select I2C and I2C_NOMADIK so
we know that this probe will always be successful.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Having this driver selected here only cause problems, get it
out of there and selected it from menuconfig or wherever
instead. Mea culpa.
Cc: Mathieu Poirer <mathieu.poirier@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ux500 platform requires CPU_FREQ_TABLE support to be enabled
for its CPU_FREQ implementations, so automatically select that
when CPU_FREQ is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
[Rebased due to missing other patches in the stack]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The cache controller needs to be enabled for the
cortex-a9 specific errata that are also selected
to work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At least one platform needs to be selected, so pick the u8500
development board if nothing else is selected. The first
menu to choose the actual platform is meaningless and can be
made invisible.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andreas Westin