This patch (as811) removes some stale testing code from the root-hub
resume routine in ohci-hcd. It also adds a spin_lock_irq() call that
inadvertently got left out of an error pathway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
replace open coded kmemdup() to save some screen space,
and allow inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as808b) moves the Root Hub Status Change interrupt-disable
code in ohci-hcd back into the interrupt handler proper, to avoid the
chance of adverse interactions with mediocre hardware implementations.
It also deletes the root-hub status timer from within the interrupt-enable
routine. There's no need to poll for status any more once interrupts are
re-enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as806) fixes a compiler warning when ohci-hcd is built
with CONFIG_PM turned off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as804) makes USB driver matching ignore the interface
class, subclass, and protocol if the device class is Vendor Specific.
Drivers can override this policy by specifying a Vendor ID as part
of the match; then vendor-specific matches are allowed.
Linus Walleij has reported a problem this patch fixes. When a
particular mass-storage device is switched from mass-storage mode to
Media Transfer Protocol, the interface class remains set to mass-storage
and usb-storage binds to it erroneously, even though the device class
changes to Vendor-Specific.
This may cause a problem for some drivers until their match records can
be updated to include Vendor IDs. But if it does, then those records
were broken to begin with.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB HID driver doesn't include any code to handle a STALL on the
interrupt endpoint. While this may be uncommon, it does happen
sometimes. This patch (as805) adds a fix.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wireless USB Host Controllers accept a large number of devices per
host, which shows up as a large number of ports in its root hub.
When the number of ports in a hub device goes over 16, the activation
of the hub fails with the cryptic message in klogd.
hub 2-0:1.0: activate --> -22
Following this further, it was seen that:
hub_probe()
hub_configure()
generates pipe number
pseudo allocates buffer 'maxp' bytes in size using usb_maxpacket()
The endpoint descriptor for a root hub interrupt endpoint is
declared in
drivers/usb/core/hcd.c:hs_rh_config_descriptor and declares it
to be size two (supporting 15 devices max).
hub_activate()
usb_hcd_submit_urb()
rh_urb_enqueue()
urb->pipe is neither int nor ctl, so it errors out
rh_queue_status()
Returns -EINVAL because the buffer length is smaller
than the minimum needed to report all the hub port
bits as in accordance with USB2.0[11.12.3]. There has
to be trunc((PORTS + 1 + 7) / 8) bytes of space at
least.
Alan Stern confirmed that the reason for reading maxpktsize and not
the right amount is because some hubs are known to return more data
and thus cause overflow.
So this patch simply changes the code to make the interrupt endpoint's
max packet size be at least the minimum required by USB_MAXCHILDREN
(instead of a fixed magic number) and add documentation for that. This
way we are always ahead of the limit.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current Wireless USB host hardware (Intel i1480 for example) allows up
to 22 devices to connect, thus bringing up the max number of children
in the WUSB Host Controller to 22 'fake' ports. Upcoming hardware
might raise that limit.
Makes almost no difference to go to 31, as the bit arrays are
byte-aligned (plus an extra bit in general), so 22 bits fit in 4 bytes
as 31 do.
As well, the only other array that depends on USB_MAXCHILDREN is
'struct usb_hub->indicator'. By declaring it 'u8' instead of 'enum
hub_led_mode', we reduce the size of each entry from 4 bytes (in i386)
to 1, which will add as we when are doubling USB_MAXCHILDREN
(with 16 the size of that array is 64 bytes, with 31 would be 128; by
using u8 that goes down to 31 bytes).
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- ->init_queue() does not need the elevator passed in
- ->put_request() is a hot path and need not have the queue passed in
- cfq_update_io_seektime() does not need cfqd passed in
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch modifies blk_rq_map/unmap_user() and the cdrom and scsi_ioctl.c
users so that it supports requests larger than bio by chaining them together.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The target mode support is mapping in bios using bio_map_user. The
current targets do not need their len to be aligned with a queue limit
so this check is causing some problems. Note: pointers passed into the
kernel are properly aligned by usersapace tgt code so the uaddr check
in bio_map_user is ok.
The major user, blk_bio_map_user checks for the len before mapping
so it is not affected by this patch.
And the semi-newly added user blk_rq_map_user_iov has been failing
out when the len is not aligned properly so maybe people have been
good and not sending misaligned lens or that path is not used very
often and this change will not be very dangerous. st and sg do not
check the length and we have not seen any problem reports from those
wider used paths so this patch should be fairly safe - for mm
and wider testing at least.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This adds a new timestamp message to blktrace, giving the timeofday when
we starting tracing. This helps user space correlate block trace events
with eg an application strace.
This requires a (compatible) update to blkparse. The changed blkparse
is still able to process traces generated by older kernels, and older
versions of blkparse should silently ignore the new records (because
they have a pid of 0).
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Correct a problem seen on later kernels running the NetPIPE application.
Specifically, NetPIPE would begin running very slowly at the 1533 packet
size. It was determined that Spidernet slowed with an idle DMA engine.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In an earlier patch, code was added to pad packets that were less that
ETH_ZLEN (60) bytes using the skb_pad function. This has caused hangs when
accessing certain NFS mounted file systems. This patch removes the check
and solves the NFS problem. The driver, with this patch, has been tested
extensively. Please apply.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bonding driver unconditionnaly dereference get_stats function pointer
for each of its slave device. This patch
- adds a check for NULL dev->get_stats pointer in bond_get_stats
- prints a notice when the bonding device enslave a device without
get_stats function.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Confusingly NET_PCI is also set for for non-PCI EISA configurations where
building this driver will result in a build error due to a reference to
pci_release_regions.
While at it, remove the EXPERIMENTAL - in all its uglyness and despite
the sincerest attempts of the buggy hardware the driver is known to work.
Also limit the driver to the Atlas board - the only known system to ever
use the SAA9730 before Phillips ended the short live of the SAA9730.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes persistant -> persistent in actual C code. (part 1 changed
docs/comments).
Compile-tested.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch converts a if () BUG(); construct to BUG_ON();
which occupies less space, uses unlikely and is safer when
BUG() is disabled.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch converts a if () BUG(); construct to BUG_ON();
which occupies less space, uses unlikely and is safer when
BUG() is disabled.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch converts a if () BUG(); construct to BUG_ON();
which occupies less space, uses unlikely and is safer when
BUG() is disabled.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses some
misc words.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses some
+words starting with the letters 'U-Z'.
Looks like I made it through the alphabet...just in time to start over again
+too! Maybe I can fit more profound fixes into the next round...? Time will
+tell. :)
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses some
+words starting with the letter 'T'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
jiffies.h includes a comment informing that jiffies_64 must be read with the
assistance of the xtime_lock seqlock. The comment text, however, calls
jiffies_64 "not volatile", which should probably read "not atomic".
Signed-off-by: Chase Venters <chase.venters@clientec.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Make clocksource_mips public and get rid of mips_hpt_read,
mips_hpt_mask.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now we have both function and macro version of do_IRQ() and the former
is used only by DEC and non-preemptive kernel. This patch makes
everyone use the macro version and removes the function version.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
r4k_flush_cache_all() and r4k_flush_cache_mm() case: these are noop if
the CPU did not have dc_aliases. It would mean we do not need to care
about icache here.
r4k_flush_cache_range case: if r4k_flush_cache_mm() did not need to
care about icache, it would be same for this function.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Further incorporation of generic irq framework. Replacing __do_IRQ()
by proper flow handler would make the irq handling path a bit simpler
and faster.
* use generic_handle_irq() instead of __do_IRQ().
* use handle_level_irq for obvious level-type irq chips.
* use handle_percpu_irq for irqs marked as IRQ_PER_CPU.
* setup .eoi routine for irq chips possibly used with handle_percpu_irq.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a big irq cleanup patch.
* Use set_irq_chip() to register irq_chip.
* Initialize .mask, .unmask, .mask_ack field. Functions for these
method are already exist in most case.
* Do not initialize .startup, .shutdown, .enable, .disable fields if
default routines provided by irq_chip_set_defaults() were suitable.
* Remove redundant irq_desc initializations.
* Remove unnecessary local_irq_save/local_irq_restore, spin_lock.
With this cleanup, it would be easy to switch to slightly lightwait
irq flow handlers (handle_level_irq(), etc.) instead of __do_IRQ().
Though whole this patch is quite large, changes in each irq_chip are
not quite simple. Please review and test on your platform. Thanks.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Luiz Fernando N. Capitulino