Most architectures use the same implementation. Collapse the common ones
into a single weak function that can be overridden.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
On some PAE architectures, the entire range of physical memory could reside
outside the 32-bit limit. These systems need the ability to specify the
initrd location using 64-bit numbers.
This patch globally modifies the early_init_dt_setup_initrd_arch() function to
use 64-bit numbers instead of the current unsigned long.
There has been quite a bit of debate about whether to use u64 or phys_addr_t.
It was concluded to stick to u64 to be consistent with rest of the device
tree code. As summarized by Geert, "The address to load the initrd is decided
by the bootloader/user and set at that point later in time. The dtb should not
be tied to the kernel you are booting"
More details on the discussion can be found here:
https://lkml.org/lkml/2013/6/20/690https://lkml.org/lkml/2012/9/13/544
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/openrisc uses of the __cpuinit macros from
all C files. Currently openrisc does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
show_regs() is inherently arch-dependent but it does make sense to print
generic debug information and some archs already do albeit in slightly
different forms. This patch introduces a generic function to print debug
information from show_regs() so that different archs print out the same
information and it's much easier to modify what's printed.
show_regs_print_info() prints out the same debug info as dump_stack()
does plus task and thread_info pointers.
* Archs which didn't print debug info now do.
alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r,
metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc,
um, xtensa
* Already prints debug info. Replaced with show_regs_print_info().
The printed information is superset of what used to be there.
arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86
* s390 is special in that it used to print arch-specific information
along with generic debug info. Heiko and Martin think that the
arch-specific extra isn't worth keeping s390 specfic implementation.
Converted to use the generic version.
Note that now all archs print the debug info before actual register
dumps.
An example BUG() dump follows.
kernel BUG at /work/os/work/kernel/workqueue.c:4841!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000
RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6
RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246
RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a
RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650
0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d
ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760
Call Trace:
[<ffffffff81000312>] do_one_initcall+0x122/0x170
[<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8
[<ffffffff81c47760>] ? rest_init+0x140/0x140
[<ffffffff81c4776e>] kernel_init+0xe/0xf0
[<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0
[<ffffffff81c47760>] ? rest_init+0x140/0x140
...
v2: Typo fix in x86-32.
v3: CPU number dropped from show_regs_print_info() as
dump_stack_print_info() has been updated to print it. s390
specific implementation dropped as requested by s390 maintainers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both dump_stack() and show_stack() are currently implemented by each
architecture. show_stack(NULL, NULL) dumps the backtrace for the
current task as does dump_stack(). On some archs, dump_stack() prints
extra information - pid, utsname and so on - in addition to the
backtrace while the two are identical on other archs.
The usages in arch-independent code of the two functions indicate
show_stack(NULL, NULL) should print out bare backtrace while
dump_stack() is used for debugging purposes when something went wrong,
so it does make sense to print additional information on the task which
triggered dump_stack().
There's no reason to require archs to implement two separate but mostly
identical functions. It leads to unnecessary subtle information.
This patch expands the dummy fallback dump_stack() implementation in
lib/dump_stack.c such that it prints out debug information (taken from
x86) and invokes show_stack(NULL, NULL) and drops arch-specific
dump_stack() implementations in all archs except blackfin. Blackfin's
dump_stack() does something wonky that I don't understand.
Debug information can be printed separately by calling
dump_stack_print_info() so that arch-specific dump_stack()
implementation can still emit the same debug information. This is used
in blackfin.
This patch brings the following behavior changes.
* On some archs, an extra level in backtrace for show_stack() could be
printed. This is because the top frame was determined in
dump_stack() on those archs while generic dump_stack() can't do that
reliably. It can be compensated by inlining dump_stack() but not
sure whether that'd be necessary.
* Most archs didn't use to print debug info on dump_stack(). They do
now.
An example WARN dump follows.
WARNING: at kernel/workqueue.c:4841 init_workqueues+0x35/0x505()
Hardware name: empty
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #9
0000000000000009 ffff88007c861e08 ffffffff81c614dc ffff88007c861e48
ffffffff8108f50f ffffffff82228240 0000000000000040 ffffffff8234a03c
0000000000000000 0000000000000000 0000000000000000 ffff88007c861e58
Call Trace:
[<ffffffff81c614dc>] dump_stack+0x19/0x1b
[<ffffffff8108f50f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8108f56a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8234a071>] init_workqueues+0x35/0x505
...
v2: CPU number added to the generic debug info as requested by s390
folks and dropped the s390 specific dump_stack(). This loses %ksp
from the debug message which the maintainers think isn't important
enough to keep the s390-specific dump_stack() implementation.
dump_stack_print_info() is moved to kernel/printk.c from
lib/dump_stack.c. Because linkage is per objecct file,
dump_stack_print_info() living in the same lib file as generic
dump_stack() means that archs which implement custom dump_stack()
- at this point, only blackfin - can't use dump_stack_print_info()
as that will bring in the generic version of dump_stack() too. v1
The v1 patch broke build on blackfin due to this issue. The build
breakage was reported by Fengguang Wu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390 bits]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Idle poller with an extra check_pgt_cache() invocation. Use the core
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130321215234.886530981@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prevents build issue with updated toolchain
Reported-by: Jack Thomasson <jkt@moonlitsw.com>
Tested-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Commit 287ad220cd tried to set up the argument
to schedule_tail, but ended up using TI_STACK which isn't a defined symbol.
Sadly, the old openrisc compiler silently ignores this fact and it was first
discovered now when building with an updated toolchain.
Reported-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
vmalloc'ed pages are faulted into a process' page tables on demand. In
order to facilitate this, do_page_fault needs to know whether it was
called via a page fault exception or a TLB-miss exception.
This patch adds a wrapper around the _x_page_fault_handler entry points
that the TLB-miss exceptions can call into in order to have the relevant
parameter set to satisfy do_page_fault.
This fixes a bug and is "good enough" for now. That said, this whole
handling of vmalloc needs to be audited for correctness at some point.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
pm_idle() on openrisc was dead code.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: linux@lists.openrisc.net
Signed-off-by: Jonas Bonn <jonas@southpole.se>
The kernel might be invoked through the reset vector, so to
preserve parameters passed to it, temp regs that are not
in the function parameter range needs to be used.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This is modelled on commits such as the one below:
Commit fc1c3a003e ("sh: use kbuild.h
instead of defining macros in asm-offsets.c") introduced in v2.6.26.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
schedule_tail() requires that the 'prev' task be passed as an argument
to it. This arg is set in _switch, just before 'returning' to one of
the ret_* functions where schedule_tail is invoked.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
getname() is intended to copy pathname strings from userspace into a
kernel buffer. The result is just a string in kernel space. It would
however be quite helpful to be able to attach some ancillary info to
the string.
For instance, we could attach some audit-related info to reduce the
amount of audit-related processing needed. When auditing is enabled,
we could also call getname() on the string more than once and not
need to recopy it from userspace.
This patchset converts the getname()/putname() interfaces to return
a struct instead of a string. For now, the struct just tracks the
string in kernel space and the original userland pointer for it.
Later, we'll add other information to the struct as it becomes
convenient.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that IRQ domains are in use, we should be acting on domain-local
IRQ numbers (hwirq) instead of 'global' ones.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
When using audit on OpenRISC, an audit arch is needed. This defines
it and fixes a compile-time bug uncovered in linux-next, likely from a
cut/paste from an arch with 64/32-bit modes that defined arch_arch():
arch/openrisc/kernel/ptrace.c:190:2: error: implicit declaration of function 'audit_arch'
This replaces it with the newly defined AUDIT_ARCH_OPENRISC, since it
is only 32-bit, and currently only operates in big-endian mode.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The function sys_or1k_atomic was using call-saved registers without
restoring their value before returning. This is a faux pas: either
we need to restore their values or use scratch regs; the latter is
less code so that's the route this patch takes.
Thanks to David Hennerström for doing most of the heavy-lifting in
tracking this one down.
Reported-by: Davd Hennerström <david.hennerstrom@aacmicrotec.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This switches OpenRISC over to fully using the generic dma-mapping
framework. This was almost already the case as the architecture's
implementation was essentially a copy of the generic header.
This also brings this architecture in line with the recent changes
to dma_map_ops (adding attributes to ops->alloc).
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This moves OpenRISC to using the irqdomain infrastructure. This doesn't
fundamentally change anything other than that it will be easier to have
multiple interrupt controllers in the future.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jonas Bonn <jonas@southpole.se>
Link: http://lkml.kernel.org/r/20120503085035.083343435@linutronix.de
The pt_regs struct had both a 'syscallno' field and an 'orig_gpr11' field
and it wasn't really clear how these were supposed to be used. This patch
removes the syscallno field altogether and makes orig_gpr11 work more
like other architectures: keep track of syscall number in progress or
hold -1 for non-syscall exceptions.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
dump_stack() is used by modules and needs to be exported.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
It takes a couple of instructions to actually configure a clock event
so setting an alarm just 1 clock cycle in the future isn't going to work;
doing so results in setting an alarm in the "past" in which case the event
won't fire until the timer overflows and rolls back around to the "current
time".
Not quite sure how many clock cycles it actually takes to get through to
actually writing the register, but 100 seems to work reliably.
Use generic helper to set up the clock event while we're at it.
Reported-by: Jan Schulte <jan.schulte@aacmicrotec.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
setup_rt_frame() needs to return an indication of whether it succeeded
or failed in setting up the signal stack frame. If setup_rt_frame()
fails then we must not modify current->blocked.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
get_signal_to_deliver() already resets the signal handler if
SA_ONESHOT is set in ka->sa.sa_flags, there's no need to do it again
in handle_signal(). Furthermore, because we were modifying
ka->sa.sa_handler (which is a copy of sighand->action[]) instead of
sighand->action[] the original code actually had no effect on signal
delivery.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Instead of open coding the sequence from force_sigsegv() just call
it. This also fixes a bug because we were modifying ka->sa.sa_handler
(which is a copy of sighand->action[]), whereas the intention of the
code was to modify sighand->action[] directly.
As the original code was working with a copy it had no effect on
signal delivery.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This patch enables passing a fdt pointer to the kernel.
This makes for the kernel parameter API:
void kernel(unsigned int fdt);
which, in accordance with the OpenRISC ABI results in:
r3 = pointer to fdt
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Commits d7e7528bcd and
b05d8447e7 simplified the usage of the
audit_syscall_[entry|exit] functions. Unfortunately, the OpenRISC
architecture didn't get fixed up along with the other architectures when
those patches were pushed. This makes the relevant changes to this
architecture.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Grant Likely