Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and
DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.
Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The touch screen controller in the TPS6507x chip needs values that are
dependent on the characteristics of the touch screen hardware being used
in the board design. In addition, the board provides version information
that is exposed via the kernel input sub-system.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On some platforms like DM355, the number of EDMA parameter slots available
for EDMA_SLOT_ANY usage are few. In such cases, if MMC/SD uses 16 slots
for each instance of MMC controller, then the number of slots available
for other modules will be very few.
By passing the number of EDMA slots to be used in MMC driver from platform
data, EDMA slots available for other purposes can be controlled.
Most of the platforms will not use this platform data variable. But on
DM355, as the number of EDMA resources available is limited, the number of
scatter- gather segments used inside the MMC driver can be 8 (passed as
platform data) instead of 16. On DM355, when the number of scatter-gather
segments was reduced to 8, I saw a performance difference of about
0.25-0.4 Mbytes/sec during write. Read performance variations were
negligible.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DA8xx OHCI driver fails to load due to failing clk_get() call for the USB 2.0
clock. Arrange matching USB 2.0 clock by the clock name instead of the device.
(Adding another CLK() entry for "ohci.0" device won't do -- in the future I'll
also have to enable USB 2.0 clock to configure CPPI 4.1 module, in which case
I won't have any device at all.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
More complete AEMIF support for boards.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added PINMUX configurations for the CLKOUT0 .. CLKOUT2
functions, for boards that want to use these clocks.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Board code may want to use them.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows for a more flexible ioremap() interception based on iotable
contents.
With this patch, the ioremap() interception code can properly translate
addresses only after davinci_soc_info has been initialized. Consequently,
in soc-specific init functions, davinci_common_init() has to happen before any
ioremap() attempts. The da8xx init sequence has been suitably modified to meet
this restriction.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the pinmux implementation so as to ioremap() the pinmux
register area on first use.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch implements the following:
- interrupt initialization uses ioremap() instead of passing a virtual address
via davinci_soc_info.
- machine definitions directly point to cp_intc_init() or davinci_irq_init()
- davinci_intc_type and davinci_intc_base now get initialized in controller
specific init functions instead of davinci_common_init()
- minor fix in davinci_irq_init() to use intc_irq_num instead of
DAVINCI_N_AINTC_IRQ
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the psc and clock control code to use ioremap()ed
registers.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch eliminates IO_ADDRESS() usage for Davinci timer definitions. The
timer code has correspondingly been modified to ioremap() MMRs instead.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch replaces the jtag id base info in davinci_soc_info with a physical
address which is then ioremap()ed within common code.
This patch (in combination with a similar change for PSC) will allow us to
eliminate the SYSCFG nastiness in DA8xx code.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the RTC unlock code to use ioremap() maps instead of
IO_ADDRESS() translation.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the gpio_base definition in davinci_soc_info to be a
physical address, which is then ioremap()ed by the gpio initialization
function.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In the edma driver, most of the long lines in 'if condition' are
broken after the logical operator '&&' except two instances.
This patch fixes that to bring consistency across the file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch replaces occurences of (1 << x) with
BIT(x) as it makes for much better reading.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In the edma driver, there are couple of instances where braces
are used for a single statement 'if' construct.
There are other instances where 'else' part of the if-else construct
does not use braces even if the 'if' part is a multi-line statement.
This patch fixes both.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
'edma_info' structure inside the edma driver represents
a single instance of edma channel controller. Call it
'edma_cc' instead. This also avoids readers confusing
it with an instance of edma_soc_info structre which
carries the platform data for a single channel controller
instance.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
With this patch, AR7 type uart ports are not reset via pwremu registers. This
allows davinci_serial_init() reuse on tnetv107x soc.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch implements davinci serial cleanups towards having this code
reusable on tnetv107x.
The change reuses the platform data membase field to hold the remapped space.
By disabling the UPF_IOREMAP flag in the platform data, we prevent
the 8250 driver from repeating the ioremap.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The uart pdata array is already terminated by a zero flag field.
This patch reuses this terminator and eliminates DAVINCI_MAX_NR_UARTS
definition. This way, future platforms can have different number of uarts
initialized via davinci_serial_init().
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The earlier watchdog reset mechanism had a couple of limitations. First, it
embedded a reference to "davinci_wdt_device" inside common code. This
forced all derived platforms (da8xx and tnetv107x) to define such a device.
This also would have caused problems in including multiple socs in a single
build due to symbol redefinition.
With this patch, davinci_watchdog_reset() now takes the platform device as an
argument. The davinci_soc_info struct has been extended to include a reset
function and a watchdog platform_device. arch_reset() then uses these
elements to reset the system in a SoC specific fashion.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pinmux registers are sequential, and do not need to be enumerated out as they
currently are. This reduces code volume and keeps things simple.
If some future SoC comes up with a discontiguous register map, PINMUX() can
then be expanded with local token pasting.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch eliminates the global gpio_lock, and implements a per-controller
lock instead. This also switches to irqsave/irqrestore locks in case gpios
are manipulated in isr.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows for gpio controllers that deviate from those found on
traditional davinci socs. davinci_soc_info has an added field to indicate the
soc-specific gpio controller type. The gpio initialization code then bails
out if necessary.
More elements (tnetv107x) to be added later into enum davinci_gpio_type.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch renders the inlined gpio accessors in gpio.h independent of the
underlying controller's register layout. This is done by including three new
fields in davinci_gpio_controller to hold the addresses of the set, clear, and
in data registers.
Other changes:
1. davinci_gpio_regs structure definition moved to gpio.c. This structure is
no longer common across all davinci socs (davinci_gpio_controller is).
2. controller base address calculation code (gpio2controller()) moved to
gpio.c as this was no longer necessary for the inline implementation.
3. modified inline range checks to use davinci_soc_info.gpio_num instead of
DAVINCI_N_GPIO.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Renamed gpio types to something more sensible:
struct gpio_controller --> struct davinci_gpio_regs
struct davinci_gpio --> struct davinci_gpio_controller
gpio2controller() --> gpio2regs()
irq2controller() --> irq2regs()
This change also moves davinci_gpio_controller definition to gpio.h.
Eventually, the gpio registers structure will be moved to gpio.c and no longer
a common cross-soc definition.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The IDE platform device is registered in three different places (2 board files
for DM644x and in dm646x.c for DM646x) while both the IDE base address and the
IDE IRQ are the same for both SoCs -- therefore, the proper place for the IDE
platform seems to be in devices.c. Merge the IDE platform data and registration
code and create davinci_init_ide() in place of dm646x_init_ide()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
linux/compiler.h is required for __iomem
linux/types.h is required u32
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows socs to override the divider ratio mask by setting an
optional field (div_ratio_mask) in the pll_data structure.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Extended the MUX configuration to allow use of GPIO
terminals 64..57.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The board file #define's its own version of EMIFA base addresses, while there
are DA8XX_AEMIF_*_BASE macros #define'd in <mach/da8xx.h>. Start using them
instead.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently each DaVinci board file #define's its own version of the EMIFA base
addresses (all named DAVINCI_ASYNC_EMIF_*_BASE), which leads to duplication.
Move these #define's to the SoC specific headers, changing their prefixes from
'DAVINCI' to the 'DM355', 'DM644X', and 'DM646X' since all these base addresses
are SoC specific...
And while at it, rename DM646X_ASYNC_EMIF_DATA_CE0_BASE to
DM646X_ASYNC_EMIF_CS2_SPACE_BASE in order to match the DM646x datasheet.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added tnetv107x cpu type definitions and cpu identification macros.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IRQ numbers as defined for tnetv107x cp_intc.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added definitions for LPSC modules in the tnetv107x SOC
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added list of muxed pins on the tnetv107x SOC.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename da8xx_pinmux_setup() to davinci_cfg_reg_list() and promote it for use in
other SOCs that may need the ability to configure multiple pins in one shot.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current clock control code always gates the clock (PSC state Disable = 2)
on clk_disable(). Some on-chip peripherals (e.g. LCD controller on TNETV107X)
need to be put into SwRstDisable = 0 on clock disable, to maintain
hardware sanity.
This patch extends the davinci_psc_config() arguments to pass in the desired
module state instead of a boolean enable/disable. Further, clk_disable() now
checks for the PSC_SWRSTDISABLE clk flag before selecting the target state.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Host map configuration instructs the interrupt controller to route interrupt
channels to FIQ or IRQ lines. Currently, DA8xx family of devices leave these
registers at their reset-default values.
TNETV107X however does not have sane reset defaults, and therefore this
architecture needs to reconfigure the host-map such that channels 0 and 1
go to FIQ, and the remaining channels raise IRQs.
This patch adds an optional host map argument to cp_intc_init() for this.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
timer_init() programs timer64 hardware. The module should ideally be brought
out of reset before this happens.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Preliminary modification prior to adding support for TNETV107X based on
ARM1176. This change allows for CPUs other than ARM926T to be used for Davinci
derivative SoCs. Existing devices (DA8x and DMx) operate unchanged.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the ISR in the EDMA driver clears the pending interrupt for all
channels without regard to whether that channel has a registered callback
or not.
This causes problems for devices like DM355/DM365 where the multimedia
accelerator uses EDMA by polling on the interrupt pending bits of some of the
EDMA channels. Since these channels are actually allocated through the Linux
EDMA driver (by an out-of-kernel module), the same shadow region is used by
Linux and accelerator. There a race between the Linux ISR and the polling code
running on the accelerator on the IPR (interrupt pending register).
This patch fixes the issue by making the ISR clear the interrupts only for
those channels which have interrupt enabled. The channels which are allocated
for the purpose of being polled on by the accelerator will not have a callback
function provided and so will not have IER (interrupt enable register) bits set.
Tested on DM365 and OMAP-L137/L138 with audio and MMC/SD (as EDMA users).
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Archith John Bency <archith@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The merge for 2.6.34 brings in 8-bit support to the DaVinci MMC/SD driver.
This patch updates the platform data for DA830/OMAP-L137 EVM to use 8-wire
support available in the driver.
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The DA830/OMAP-L137 EVM has GPIO based card detection logic, but the current
code does not use it.
Add support for GPIO based card detection to avoid reading the card to see
if a card is present or not.
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup usage of void pointers when using genirq. genirq API
takes and returns void *, where this GPIO API is using those
as __iomem pointers.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Sekhar Nori