Move the allocation of display_timing memory from of_get_display_timing() to
of_get_display_timings(). This allows us to use of_get_display_timing()
in a way that doesn't require dynamic memory allocation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
By default, the ssd1307 controller uses an addressing mode called page
addressing. This mode only increments the column cursor in memory when
writing data but will not increments the page cursor when we are at the
end of the page.
However, the controller supports another addressing mode, called
horizontal addressing, that will maintain both the page and column
cursors when writing data to the controller.
That means that we can just remove the code that increments the current
page address and reset the column cursor when reaching the end of the
line, allowing to have a lower data overhead, and a simpler driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The code until now was sending only 1pixel-wide page segment at once,
and started a new transfer every time. It has proven very inefficient,
because for one byte to display on the screen, we had to actually send 3
bytes over I2C: the address, the type of data that was going to the
controller, and then the actual data.
This patches changes that by sending a whole page at once, avoiding most
of this expensive overhead.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To efficiently send a whole page to the display, we need to be able to
manipulate more easily the data arrays that has to be sent to the OLED
controller. As such, this patch introduces a ssd1307fb_array structure
that handles both the small header to be sent over i2c, which contains
the type of information sent, and the raw bytes after that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The Solomon SSD1306 OLED controller is very similar to the SSD1307,
except for the fact that the power is given through an external PWM for
the 1307, and while the 1306 can generate its own power without any PWM.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `goldfish_fb_remove':
drivers/video/goldfishfb.c:301: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `goldfish_fb_probe':
drivers/video/goldfishfb.c:247: undefined reference to `dma_alloc_coherent'
drivers/video/goldfishfb.c:280: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A simple frame-buffer describes a raw memory region that may be rendered
to, with the assumption that the display hardware has already been set
up to scan out from that buffer.
This is useful in cases where a bootloader exists and has set up the
display hardware, but a Linux driver doesn't yet exist for the display
hardware.
Examples use-cases include:
* The built-in LCD panels on the Samsung ARM chromebook, and Tegra
devices, and likely many other ARM or embedded systems. These cannot
yet be supported using a full graphics driver, since the panel control
should be provided by the CDF (Common Display Framework), which has been
stuck in design/review for quite some time. One could support these
panels using custom SoC-specific code, but there is a desire to use
common infra-structure rather than having each SoC vendor invent their
own code, hence the desire to wait for CDF.
* Hardware for which a full graphics driver is not yet available, and
the path to obtain one upstream isn't yet clear. For example, the
Raspberry Pi.
* Any hardware in early stages of upstreaming, before a full graphics
driver has been tackled. This driver can provide a graphical boot
console (even full X support) much earlier in the upstreaming process,
thus making new SoC or board support more generally useful earlier.
[akpm@linux-foundation.org: make simplefb_formats[] static]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Rob Clark <robclark@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When booting with DT, there's a crash when omapfb is probed. This is
caused by the fact that omapdss+DT is not yet supported, and thus
omapdss is not probed at all. On the other hand, omapfb is always
probed. When omapfb tries to use omapdss, there's a NULL pointer
dereference crash. The same error should most likely happen with omapdrm
and omap_vout also.
To fix this, add an "initialized" state to omapdss. When omapdss has
been probed, it's marked as initialized. omapfb, omapdrm and omap_vout
check this state when they are probed to see that omapdss is actually
there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Impact:
1:convert all remain take_over_console to do_take_over_console
2:update take_over_console to do_take_over_console in comment
Commit dc9641895a ("vt: delete unneeded functions
register_con_driver|take_over_console") delete take_over_console,
but forget to convert remain take_over_console's users to new API
do_take_over_console, this patch fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are only two place use unregister_con_driver now, this patch
convert them to do_unregister_con_driver too, then we can delete
unregister_con_driver whos function can be achieved with do_unregister_con_driver
easily to reduce code size and duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there is no place use fbcon_takeover, and
fbcon_takeover has huge duplication code with
do_fbcon_takeover, we can achieve fbcon_takeover's
function with do_fbcon_takeover easily, so we
can just delete it.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 054430e773 (fbcon: fix locking harder),
there is only one place use do_fbcon_takeover now, this patch
convert it to do_fbcon_takeover too, then we can delete
fbcon_takeover whos function can be achieved with do_fbcon_takeover
easily to reduce code size and duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The new SOLO6X10 driver needs the built-in console fonts, specifically
the VGA8x16 font and building it without console support results in
a link error error.
drivers/built-in.o: In function `solo_osd_print':
:(.text+0x7d3424): undefined reference to `find_font'
This adds a dependency on the CONFIG_FONTS symbol and changes the
console code to always build the base driver even if there are
no specific fonts built-in.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fbcon uses workqueues and it has no real dependency of scheduling these on the
cpu which scheduled them.
On a idle system, it is observed that and idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.
This patch replaces system_wq with system_power_efficient_wq.
Cc: Dave Airlie <airlied@redhat.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
commit 6cd2c7db4 (videomode: videomode_from_timing work) changed the name of
the function from videomode_from_timing() to videomode_from_timings().
commit 32ed6ef1 (videomode: create enum for videomode's display flags) changed
the 'data_flags' field in videomode structure to 'flags'
Adapt to these changes in order to fix the following errors:
drivers/video/mxsfb.c:761:3: error: too many arguments to function 'videomode_from_timing'
drivers/video/mxsfb.c:761:7: error: void value not ignored as it ought to be
drivers/video/mxsfb.c:768:9: error: 'struct videomode' has no member named 'data_flags'
drivers/video/mxsfb.c:770:9: error: 'struct videomode' has no member named 'data_flags'
Also, select VIDEOMODE_HELPER instead of OF_VIDEOMODE, as this one is
deprecated.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The support for PB1100, PB1500, and PB1550 got merged into the code for
DB1000 and DB1550 code in v3.7. When that was done the three related
Kconfig symbols were dropped. But not all related Kconfig macros were
removed. Do so now.
Note that the PB1100 code in the Au1100 LCD driver is removed entirely
and not converted to use its current Kconfig macro. That is done because
the macros it uses (PB1100_G_CONTROL, PB1100_G_CONTROL_BL, and
PB1100_G_CONTROL_VDD) are never defined. Actually only one of these was
ever defined (PB1100_G_CONTROL) but that define was removed in v2.6.34.
So, as far as I can tell, this code could have never compiled.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5040/
Acked-by: John Crispin <blogic@openwrt.org>
Commit 11bd5933ab ("fbdev/ps3fb: use vm_iomap_memory()") introduced
the following warning:
drivers/video/ps3fb.c: In function 'ps3fb_mmap':
drivers/video/ps3fb.c:712:2: warning: suggest parentheses around '+' inside '<<' [-Wparentheses]
Fix this by adding the parentheses.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the I2C adapter needed by the TFP410 device is not available yet,
return EPROBE_DEFER so that the device will get probed again.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add proper error handling for venc_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the VENC driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add proper error handling for hdmi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the HDMI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add proper error handling for rfbi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the RFBI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add proper error handling for dsi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DSI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add proper error handling for sdi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the SDI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add proper error handling for dpi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DPI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb requires the panel drivers to have been probed when omapfb is
initialized. omapfb does not support insertion of new panels after its
probe. This causes a problem in case omapdss or the panel probes have
been deferred due to EPROBE_DEFER error, as omapfb won't find any
displays.
As a quick fix, this patch changes the omapfb probe so that if omapfb
does not find any displays, it'll return EPROBE_DEFER. This is not
perfect, as with a board with no displays, omapfb will get deferred
forever. Also, if the board has multiple displays, but only some of them
have been probed, omapfb will start and leave the unprobed displays out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using platform_driver_probe(), use module_platform_driver()
so that we can support deferred probing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb requires the panels to have been probed before omapfb's probe. We
currently manage that by having omapfb in late initcall level. However,
a much simpler way is to just change the makefile so that omapfb is
after the panel drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 100c826235 (OMAPDSS: DPI: use new
clock calculation code) breaks dpi.c compilation if DSI is not enabled
in the kernel configuration.
Fix compilation by adding dummy inline functions for the ones that dpi.c
references. The functions will never be called, as dpi.c knows that
there is no DSI device available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable supporting the DT structure of LP855x family devices. If the
platform data is NULL, the driver tries to parse a DT structure. Then,
the platform data is copied from the DT. Documentation is added as well.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'load_new_rom_data' was used for checking whether new ROM data should
be updated or not.
However, we can decide it with 'size_program' data. If the size is
greater than 0, it means updating ROM area is required. Otherwise, the
default ROM data will be used. Therefore, this duplicate platform data
can be removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The brightness of LP855x devices is controlled by I2C register or PWM
input . This mode was selected through the platform data, but it can be
chosen by the driver internally without platform data configuration.
How to decide the control mode:
If the PWM period has specific value, the mode is PWM input.
On the other hand, the mode is register-based.
This mode selection is done on the _probe().
Move 'mode' from a header file to the driver private data structure,
'lp855 x'. And correlated code was replaced.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Configurable data, backlight device name is set to constant character type.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using legacy suspend/resume methods, using newer dev_pm_ops
structure allows better control over power management. Also, use of
pm_message_t is deprecated. Thus, it is removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using legacy suspend/resume methods, using newer dev_pm_ops
structure allows better control over power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using legacy suspend/resume methods, using newer dev_pm_ops
structure allows better control over power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Platform LCD devices may need to do some device-specific initialization
before they can be used (regulator or GPIO setup, for example), but
currently the driver does not support any way of doing this. This patch
adds a probe() callback to plat_lcd_data which platform LCD devices can
set to indicate that device-specific initialization is needed.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for configuring AS3711 backlight driver from DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tomi Valkeinen