During hibernation and suspend on x86_64 save CPU registers in the saved_context
structure rather than in a handful of separate variables.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The x86_64 arch/x86/kernel/Makefile uses references into
arch/x86/kernel/cpu/... to use code from there.
Unifiy it with the nicely structured i386 way and reuse the existing
subdirectory make rules.
Also move the machine check related source into ...kernel/cpu/mcheck,
where the other machine check related code is.
No code change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move mce.c to mce_32.c to allow the later move of the x86_64 mce.c
from arch/x86/kernel/ to ...kernel/cpu/mcheck
No code change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Prepare the makefiles in x86/kernel/cpu and x86/kernel/cpu/mcheck to
be used by the x86_64 build as well.
No code change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Most of contents in crash are same.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The previous patch wasn't correctly handling the 'count' variable. If
a CPU gave bad results on the 1st or 2nd run but good results on the
3rd, it wouldn't do the correct thing. No idea if any such CPU
exists, but the patch below handles that case by discarding the bad
runs.
If a bad result (too quick, or too slow) occurs on any of the 3 runs
it will be discarded.
Also updated some comments to explain what's going on.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I ran into this problem on a system that was unable to obtain NTP sync
because the clock was running very slow (over 10000ppm slow). ntpd had
declared all of its peers 'reject' with 'peer_dist' reason.
On investigation, the tsc_khz variable was significantly incorrect
causing xtime to run slow. After a reboot tsc_khz was correct so I
did a reboot test to see how often the problem occurred:
Test was done on a 2000 Mhz Xeon system. Of 689 reboots, 8 of them
had unacceptable tsc_khz values (>500ppm):
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 21 3.048%
1999800 - 1999850 166 24.128%
1999850 - 1999900 241 35.029%
1999900 - 1999950 211 30.669%
1999950 - 2000000 42 6.105%
2000000 - 2000000 0 0.000%
2000050 - 2000100 0 0.000%
[...]
2000100 - 2015000 1 0.145% << BAD
2015000 - 2030000 6 0.872% << BAD
2030000 - 2045000 1 0.145% << BAD
2045000 < 0 0.000%
The worst boot was 2032.577 Mhz, over 1.5% off!
It appears that on rare occasions, mach_countup() is taking longer to
complete than necessary.
I suspect that this is caused by the CPU taking a periodic SMI
interrupt right at the end of the 30ms calibration loop. This would
cause the loop to delay while the SMI BIOS hander runs. The resulting
TSC value is beyond what it actually should be resulting in a higher
tsc_khz.
The below patch makes native_calculate_cpu_khz() take the best
(shortest duration, lowest khz) run of it's 3 calibration loops. If a
SMI goes off causing a bad result (long duration, higher khz) it will
be discarded.
With the patch applied, 300 boots of the same system produce good
results:
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 30 10.000%
1999800 - 1999850 166 55.333%
1999850 - 1999900 89 29.667%
1999900 - 1999950 15 5.000%
1999950 < 0 0.000%
Problem was found and tested against 2.6.18. Patch is against 2.6.22.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
1) This allows us to get alot closer to booting bzImages.
2) It means we don't have to know page_offset.
3) The Guest needs to modify the boot pagetables to create the
PAGE_OFFSET mapping before jumping to C code.
4) guest_pa() walks the page tables rather than using page_offset.
5) We don't use page_offset to figure out whether to emulate: it was
always kinda quesationable, and won't work for instructions done
before remapping (bzImage unpacking in particular).
6) We still want the kernel address for tlb flushing: have the initial
hypercall give us that, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch should apply cleanly to the 2.6.23-git7 kernel. It changes the
powernow-k8 driver code that deals with 3rd generation Opteron, Phenom,
and later processors to match the architectural pstate driver described
in the AMD64 Architecture Programmer's Manual Volume 2 Chapter 18. The
initial implementation of the hardware pstate driver for PowerNow!
used some processor-version specific features, and would not be
maintainable in the long term as the processor features changed.
This architectural driver should work on all future AMD processors.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add the BSS to the resource tree just as kernel text and kernel data are in
the resource tree. The main reason behind this is to avoid crashkernel
reservation in that area.
While it's not strictly necessary to have the BSS in the resource tree (the
actual collision detection is done in the reserve_bootmem() function before),
the usage of the BSS resource should be presented to the user in /proc/iomem
just as Kernel data and Kernel code.
Note: The patch currently is only implemented for x86 and ia64 (because
efi_initialize_iomem_resources() has the same signature on i386 and ia64).
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we fix all the opensource gfx drivers to use the DMA api's, at that time
we can yank this config options out.
[jengelh@computergmbh.de: Kconfig fixes]
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MSI interrupt handler registrations and fault handling support for Intel-IOMMU
hadrware.
This patch enables the MSI interrupts for the DMA remapping units and in the
interrupt handler read the fault cause and outputs the same on to the console.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Actual intel IOMMU driver. Hardware spec can be found at:
http://www.intel.com/technology/virtualization
This driver sets X86_64 'dma_ops', so hook into standard DMA APIs. In this
way, PCI driver will get virtual DMA address. This change is transparent to
PCI drivers.
[akpm@linux-foundation.org: remove unneeded cast]
[akpm@linux-foundation.org: build fix]
[bunk@stusta.de: fix duplicate CONFIG_DMAR Makefile line]
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch uses the updated boot protocol to do paravirtualized boot.
If the boot version is >= 2.07, then it will do two things:
1. Check the bootparams loadflags to see if we should reload the
segment registers and clear interrupts. This is appropriate
for normal native boot and some paravirtualized environments, but
inapproprate for others.
2. Check the hardware architecture, and dispatch to the appropriate
kernel entrypoint. If the bootloader doesn't set this, then we
simply do the normal boot sequence.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates for version 2.07 of the boot protocol. This includes:
load_flags.KEEP_SEGMENTS- flag to request/inhibit segment reloads
hardware_subarch - what subarchitecture we're booting under
hardware_subarch_data - per-architecture data
The intention of these changes is to make booting a paravirtualized
kernel work via the normal Linux boot protocol.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
This patch removes the crashkernel parsing from
arch/x86_64/kernel/machine_kexec.c and calls the generic function, introduced
in the last patch, in setup_bootmem_allocator().
This is necessary because the amount of System RAM must be known in this
function now because of the new syntax.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the crashkernel parsing from
arch/i386/kernel/machine_kexec.c and calls the generic function, introduced in
the last patch, in setup_bootmem_allocator().
This is necessary because the amount of System RAM must be known in this
function now because of the new syntax.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
copy_oldmem_page should not return leaving a page frame from the
previous kernel mapped.
Signed-off-by: Fernando Luis Vázquez Cao <fernando@oss.ntt.co.jp>
Acked-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpu_data is currently an array defined using NR_CPUS. This means that
we overallocate since we will rarely really use maximum configured cpus.
When NR_CPU count is raised to 4096 the size of cpu_data becomes
3,145,728 bytes.
These changes were adopted from the sparc64 (and ia64) code. An
additional field was added to cpuinfo_x86 to be a non-ambiguous cpu
index. This corresponds to the index into a cpumask_t as well as the
per_cpu index. It's used in various places like show_cpuinfo().
cpu_data is defined to be the boot_cpu_data structure for the NON-SMP
case.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here is a small patch to change the behavior of the PMU msr allocator
to avoid BUG_ON() when the MSR is unknwon. Instead, it now returns
ok, which means "I do not manage". The current allocator is not
yet managing the full set of PMU registers (e.g., GLOBAL_* on Core 2).
[watchdog] do not BUG_ON() in the MSR allocator if MSR is unknown, return ok
instead
Signed-off-by: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is from an earlier message from Christoph Lameter:
processor_core.c currently tries to determine the apicid by special casing
for IA64 and x86. The desired information is readily available via
cpu_physical_id()
on IA64, i386 and x86_64.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Additionally, boot_cpu_id needed to be exported to fix compile errors in
dma code when !CONFIG_SMP.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Convert cpu_llc_id from a static array sized by NR_CPUS to a per_cpu
variable. This saves sizeof(cpu_llc_id) * NR unused cpus. Access is
mostly from startup and CPU HOTPLUG functions.
Note there's an additional change of the type of cpu_llc_id from int to
u8 for ARCH i386 to correspond with the same type in ARCH x86_64.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch converts the x86_cpu_to_apicid array to be a per cpu
variable. This saves sizeof(apicid) * NR unused cpus. Access is mostly
from startup and CPU HOTPLUG functions.
MP_processor_info() is one of the functions that require access to the
x86_cpu_to_apicid array before the per_cpu data area is setup. For this
case, a pointer to the __initdata array is initialized in setup_arch()
and removed in smp_prepare_cpus() after the per_cpu data area is
initialized.
A second change is included to change the initial array value of ARCH
i386 from 0xff to BAD_APICID to be consistent with ARCH x86_64.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This simplifies the io_apic.c __assign_irq_vector() logic and removes
the explicit SYSCALL_VECTOR check, and also allows for vectors to be
reserved by other mechanisms (ie. lguest).
[ tglx: arch/x86 adaptation ]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't want any lockdep or other fragile machinery to run during oopses.
Use raw spinlocks directly for oops locking.
Also disables irq flag tracing there.
[ tglx: arch/x86 adaptation ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch defines the missing function smp_call_function_mask() for x86_64,
this is more or less a cut&paste of i386 function. It removes also some
duplicate code.
This function is needed by KVM to execute a function on some CPUs.
AK: Fixed description
AK: Moved WARN_ON(irqs_disabled) one level up to not warn in the panic case.
[ tglx: arch/x86 adaptation ]
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch provides a new set of functions for managing the descriptor
tables that can be used instead of putting the raw assembly in .c files.
Remodeling of store_tr() suggested by Frederik Deweerdt.
[ tglx: arch/x86 adaptation ]
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Both functions printk the same information, except for CRx and
debug registers in the show_registers() one and a bit different
manner. So move the common code into one place. This is already
done for x86_64, so I think it's worth having the same on i386.
This saves 100 bytes of .rodata section :) ...
but only 8 from .text :(
[ tglx: arch/x86 adaptation ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
They were already very similar; just use the same file now.
[ tglx: arch/x86 adaptation ]
Cc: lenb@kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ICH3 and ICH4 have undocumented HPET capabilities. This patch enables
HPET for platforms based around these ICHs.
Tested on various ICH3 and ICH4 platforms.
Because HPET is not officially documented for ICH3/4 and may not have
been validated by chipset folks, we're on thin ice here. I'd recommend
testing this patch in -hrt or -mm for a while and wait for
success/failure reports before feeding it upstream.
tglx: depends on the force_hpet command line option !
Signed-off-by: Udo A. Steinberg <us15@os.inf.tu-dresden.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds quirks to force enable HPET on Via VT8235 and
VT8237 chipsets. The datasheet for 8237 documents HPET
functionality (although wrongly) whereas HPET is undocumented
for 8235.
Tested on A7V880 (8237) and K7VT4A+ (8235) boards.
tglx: depends on the force_hept commandline option
Signed-off-by: Udo A. Steinberg <us15@os.inf.tu-dresden.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
add force_hpet boot option.
(this will be useful to make the forced-enable quirks depend on.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simple cosmetic update for the cs5536 reboot fixup; define the MSR that's used
for rebooting in geode.h, and use the define.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rafael J. Wysocki