For NX3031, the phy is managed by firmware, so driver should avoid
setting any phy registers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The commit that made the CONFIG_GFAR_NAPI code unconditional was
included at the same time as a new CONFIG_GFAR_NAPI user, resulting
in these bugus #ifdef's.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently when we do a packet flood to the Ethernet port, the console
reports error every time when a packet is dropped. This is too
redundant and cost performance. Remove message for this type of event.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for limiting the number of tx pause frames to a
default of 8. Previously, hardware would send out continuous stream of
pause frames.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds jumbo frame support for MCP79 chipsets.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for new tx statistic counters in the hardware -
unicast, multicast, and broadcast
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch enforces a stricter policy on rx errors. The driver needs to
verify whether there are multiple rx errors versus a single error.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the problems reported for 2.6.27-rc1 caused by over aggressive
power management. Turning clock off on PCI Express is problematic for WOL,
and when doing multi-booting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
igb_init_managability does not actually perform any function as the two
registers it attempts to write are both read only on the host. This patch
removes the function and all references to it from the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Three functions were left in the code that are no longer used. I am removing
these functions just to keep the code clean.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The igb_mta_set function was not being correctly used
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the PCS configuration for serdes so that the flow
control options change be set via the ethtool -A option.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With a fiber or serdes NIC installed the driver was causing a null pointer
dereference on driver unload.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The internal name was used in comments, replaced with silicon part number.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The L1 hardware contains a bug that flags a fragmented IP packet
as having an incorrect TCP/UDP checksum, even though the packet
is perfectly valid and its checksum is correct. There's no way to
distinguish between one of these good packets and a packet that
actually contains a TCP/UDP checksum error, so all we can do is
allow the packet to be handed up to the higher layers and let it
be sorted out there.
Add a comment describing this condition and remove the code that
currently fails to handle what may or may not be a checksum error.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are currently no devices supported by the e1000e driver which need
ioport resources, remove the test for it and all unnecessary code
associated with it (struct e1000_adapter elements, local variables, etc.)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a few people seem to have problems maintaining gigabit link
and it was root caused to an interaction between the managability
firmware on the host and the driver, not communicating.
The form of communication they use is the drv_load bit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
82573 EEPROMs have been shipped out with known issues. While most
people will never see the issues some people do and we know
how to address them. Warn the user if we find one of these
EEPROM issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ndev_* printk's are too lenghty and we don't need to specify
the adapter/netdev struct at all, making this a lot more readable.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set 64bits consistent DMA mask since it improves performance
in some cases. No need to check the return value since it is
not required for the driver to work.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes the 'scheduling while atomic' errors introduced by
commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code").
The first hunk of the patch removes an unnecessary
tg3_set_power_state() call. The chip will already be in the D0 state
either due to a chip reset or through a previous call to
tg3_set_power_state().
The second hunk of the patch moves the tg3_set_power_state() call
outside the critical section guarded by tg3_full_lock() and
tg3_full_unlock() functions. The power state of the device is and
should be outside the lock's domain and all other
tg3_set_power_state() calls support this.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should allow packets transmission in monitor mode for 3945. The
patch fixes a merge error with 2.6.26 kernel.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to grap nic access before accessing periphery registers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch decrements rx skb counter in scan abort handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes unhandled interrupt when HW rfkill is on during
devices start up. The behavior changes, now open is successful even
when rfkill is on. This is to align with the situation when rfkill
is set on after opening.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements rssi calculation for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch optimizes memory allocation. The cmd member of
iwl_tx_queue was allocated previously as a continuous block
of memory. This patch allocates separate memory chunks for each command
and maps/unmaps these chunks in the run time.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds few HW bug fixes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Experience with the rtl8187 driver has shown that mac80211 can make
calls to the config callback routine in rapid succession. This patch
creates a mutex that protects the private data in several of the routines
called by mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities
As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).
This should fix Fedora bug: 411481
v2: Fix typos
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the buffer on the stack and even re-using it for all led devices is bad.
Not being able to resolve the name member of the led device structure to a
meaningful value leads to confusion during ad-hoc debugging and potential
breakage in the future, if we ever decide to access the name member outside of
the registration function. Move the buffer to our private per led device
structures so that it is accessible after registration.
A quick grep didn't yield any occurence of using the led device name parameter
outside of the led device registration function, so currently we should already
be safe for normal operation.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames driver name from 4965 to AGN
The driver supports both 4965AGN and 5000AGN family
The driver's original module name iwl4965.ko remains as an alias
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes errors reported by checkpatch in iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965-base.c to iwl-agn.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses dtim_period from association, and sets the listen_interval.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-agn-rs.c: In function 'rs_clear':
iwl-agn-rs.c:2405: warning: unused variable 'priv
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in AGG flow:
u64 bitmap = 0;
bitmap |= 1 << 32 results to be 0xffffffff80000000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the led register in disassociation flow according to
rf-kill state : off - in case of rf_kill, on - otherwise.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965_fill_rs_info was used in sysfs. This info is already present
in iwl-agn-rs debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965-rs to iwl-agn-rs as it provides
rate scale capability for all AGN capable iwlwifi drivers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_set_pwr_src to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch concentrates becaon handling in iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_mac_ampdu_action to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects power_level in sysfs.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for power save for 5000 HW.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/se.h moved to mach-se/mach/se.h, update the path. We could use
mach/se.h here also, but it's preferable to be explicit when there's
only a single supported mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
iwl3945_rx_reply_rx was sending packets too early to
mac80211, before updating signal strength/quality.
This resulted in garbage power levels.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dhananjay Phadke