For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
port->dev_list maintains a list of devices attached to a given sas root port.
It needs to be mutated under a lock as contexts outside of the
single-threaded-libsas-workqueue access the list via sas_find_dev_by_rphy().
Fixup locations where the list was being mutated without a lock.
This is a follow-up to commit 5911e963 "[SCSI] libsas: remove expander
from dev list on error", where Luben noted [1]:
> 2/ We have unlocked list manipulations in sas_ex_discover_end_dev(),
> sas_unregister_common_dev(), and sas_ex_discover_end_dev()
Yes, I can see that and that is very unfortunate.
[1]: http://marc.info/?l=linux-scsi&m=131480962006471&w=2
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.
These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
* /sys/class/sas_phy/<phyX>/invalid_dword_count
* /sys/class/sas_phy/<phyX>/running_disparity_error_count
* /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
* /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Libsas forget to set the sas_address and device type of rphy lead to file
under /sys/class/sas_x show wrong value, fix that.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Tested-by: Crystal Yu <crystal_yu@usish.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The queue-depth for libsas-attached devices initializes to 32 and can
only be increased manually via sysfs to a max of 64, while mpt2sas
attached devices initialize to 254 and dynamically float via the
midlayer ->change_queue_depth interface.
No performance regression was observed with this change on the isci
driver.
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.
Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation. Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written. If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.
Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:
smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In an enclosure model where there are chaining expanders to a large body
of storage, it was discovered that libsas, responding to a broadcast
event change, would only revalidate the domain of first child expander
in the list.
The issue is that the pointer value to the discovered source device was
used to break out of the loop, rather than the content of the pointer.
This still remains non-compliant as the revalidate domain code is
supposed to loop through all child expanders, and not stop at the first
one it finds that reports a change count. However, the design of this
routine does not allow multiple device discoveries and that would be a
more complicated set of patches reserved for another day. We are fixing
the glaring bug rather than refactoring the code.
Signed-off-by: Mark Salyzyn <msalyzyn@us.xyratex.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
->queuecommand must return either 0, or one of the SCSI_MLQUEUE_* return
values. Non-transient errors are indicated by setting cmd->result before
calling ->scsi_done and returning 0. Fix libsas to adhere to this calling
convention. Note that the DID_ERROR for returns from the low-level driver
might not be correct for all cases, but it's the best we can do with
the current layering in libsas. I also suspect that the pre-existing
handling of -SAS_QUEUE_FULL should really be SCSI_MLQUEUE_HOST_BUSY, but
I'll leave that for a separate change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Switch sas_queuecommand to a normal indentation and goto based error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If expander discovery fails (sas_discover_expander()), remove the
expander from the port device list (sas_ex_discover_expander()),
before freeing it. Else the list is corrupted and, e.g., when we
attempt to send SMP commands to other devices, the kernel oopses.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Cc: stable@kernel.org
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a libsas driver to optionally provide a soft reset handler
for libata to drive. The isci driver allows software to control the
assertion/deassertion of SRST.
[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.
Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd] Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk
After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Commit 56dd2c06 "libsas: Don't issue commands to devices that have been
hot-removed" edited Darrick's original patch to remove setting 'gone' in
the sas_deform_port() path because that prevented scsi sync cache
commands from being issued when the driver was unloaded. However, this
allows true device gone notifications (as signaled port phy events) to
trigger sync cache commands to devices that are known to be unreachable.
Teach libsas which sas_deform_port() invocations are likely device gone
events.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Current version of libsas can not handle SATA NCQ error.
This patch handle SATA NCQ error as AHCI do.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
I think this stems from a misunderstanding of how the ata error handler
works. ata_scsi_cmd_error_handler() gets called with a passed in list
of commands to handle. However, that list may still not be empty when
it exits. The command ata_scsi_port_error_handler() must be called
(which takes no list) before the list will be completely emptied. This
bites the sas error handler because the two are called from different
functions and the original list has gone out of scope before
ata_scsi_port_error_handler() is called. leading to some commands
dangling on bare stack, which is a potential memory corruption issue.
Fix this by manually deleting all outstanding commands from the on-stack
list before it goes out of scope.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These flags are marked as obsolete and the checks for them have been removed
by commit 294440887b (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 14bdef982c ([libata] convert drivers to
use ata.h mode mask defines) didn't convert these two libata driver outside
drivers/ata/...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In some test envirenment, there is loopback topology test. We should
handle this during discovery.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Originally, libata required the illusion that it could access the sata
control register. Now, however, it can run perfectly well without
them, so remove the dummy routines from libsas which tried to emulate
them (but only ended up causing confusion).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ATAPI check condition needs to be treated the same as a success or
protocol return. The register returns from the PACKET command are all
correctly positioned in the device to host register FIS and so we
should collect them properly. Right at the moment this doesn't matter
because libata sends a request sense always for ATAPI errors, but if
it ever checked the registers, we should have the correct contents
just in case.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To date libsas has only looked at the attached sas address when
determining the formation of wide ports. The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other. Introduce a flag
to select stricter behavior at sas_register_ha() time. The flag can be
dropped once it is known that all libsas users expect the same behavior.
Current drivers just initialize this field to zero and get the
traditional behavior.
Reported-by: Patrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fix bug reported by Chuck. And this new version incorporate comments
from Hannes. Please consider to include it into mainline.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Tested-by: Chuck Tuffli <Chuck_Tuffli@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sd will get hung up issuing commands to flush write cache if a SAS
device behind the expander is unplugged without warning. Change libsas
to reject commands to domain devices that have already gone away.
[maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to
permit sync cache commands at module removal]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Tested-by: Haipao Fan <haipao.fan@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some cards (like mvsas) have issue troubles if non-NCQ commands are
mixed with NCQ ones. Fix this by using the libata default NCQ check
routine which waits until all NCQ commands are complete before issuing
a non-NCQ one. The impact to cards (like aic94xx) which don't need
this logic should be minimal
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
REQ_HARDBARRIER is deprecated. Remove spurious uses in the following
users. Please note that other than osdblk, all other uses were
already spurious before deprecation.
* osdblk: osdblk_rq_fn() won't receive any request with
REQ_HARDBARRIER set. Remove the test for it.
* pktcdvd: use of REQ_HARDBARRIER in pkt_generic_packet() doesn't mean
anything. Removed.
* aic7xxx_old: Setting MSG_ORDERED_Q_TAG on REQ_HARDBARRIER is
spurious. Removed.
* sas_scsi_host: Setting TASK_ATTR_ORDERED on REQ_HARDBARRIER is
spurious. Removed.
* scsi_tcq: The ordered tag path wasn't being used anyway. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We have two separate definitions for identical constants with nearly the
same name. One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).
Fix this by eliminating the libsas.h duplicate
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit 70b25f890c
Author: Tejun Heo <tj@kernel.org>
Date: Thu Apr 15 09:00:08 2010 +0900
[SCSI] fix locking around blk_abort_request()
Introduced a reference before check problem, fix this by moving the
lock shorthand code to be right at the point of actual use.
Reported-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_abort_request() expects queue lock to be held by the caller.
Grab it before calling the function.
Lack of this synchronization led to infinite loop on corrupt
q->timeout_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We should not set res to 0 in function sas_ex_discover_dev in order to let
it discover it further when wide port hotplug in .
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hotplug of phys which form wide ports simply does not work at the moment. Fix
this by adding checks at the hotplug points to see if the attached sas address
of the phy already exists (in which case it's part of a wide port) and act
accordingly.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
[jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower
case to fix a ppc64 compile error in linux-next]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a hotplug problem in the way libsas allocates ports: it loops over the
available ports first trying to add to an existing for a wide port and
otherwise allocating the next free port. This scheme only works if the port
array is packed from zero, which fails if a port gets hot unplugged and the
array becomes sparse. In that case, a new port is formed even if there's a
wide port it should be part of. Fix this by creating two loops over all the
ports: the first to see if the phy should be part of a wide port and the
second to form a new port in an empty port slot.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Paul Gortmaker