Introduce a wrapper around scsi_cmd_ioctl that takes a block device.
The function will then be enhanced to detect partition block devices
and, in that case, subject the ioctls to whitelisting.
Cc: linux-scsi@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We weren't filling in the transfer length of the
flush cache command (it transfers 4 bytes of zeroes).
Firmware didn't seem to be bothered by this, but it
should be fixed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IRQF_SHARED is required for older controllers that don't support MSI(X)
and which may end up sharing an interrupt.
Also remove deprecated IRQF_DISABLED.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A long time ago, probably in 2002, one of the distros, or maybe more than
one, loaded block drivers prior to loading the SCSI mid layer. This meant
that the cciss driver, being a block driver, could not engage the SCSI mid
layer at init time without panicking, and relied on being poked by a
userland program after the system was up (and the SCSI mid layer was
therefore present) to engage the SCSI mid layer.
This is no longer the case, and cciss can safely rely on the SCSI mid
layer being present at init time and engage the SCSI mid layer straight
away. This means that users will see their tape drives and medium
changers at driver load time without need for a script in /etc/rc.d that
does this:
for x in /proc/driver/cciss/cciss*
do
echo "engage scsi" > $x
done
However, if no tape drives or medium changers are detected, the SCSI mid
layer will not be engaged. If a tape drive or medium change is later
hot-added to the system it will then be necessary to use the above script
or similar for the device(s) to be acceesible.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: iss_storagedev@hp.com
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The P600 requires a small delay when changing states. Otherwise we may think
the board did not reset and we bail. This for kdump only and is particular
to the P600.
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Joseph Handzik <joseph.t.handzik@beardog.cce.hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Joseph Handzik <joseph.t.handzik@beardog.cce.hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
drivers/block/cciss.c: In function ‘cciss_send_reset’:
drivers/block/cciss.c:2515:2: error: implicit declaration of function ‘fill_cmd’
drivers/block/cciss.c: At top level:
drivers/block/cciss.c:2531:12: error: conflicting types for ‘fill_cmd’
drivers/block/cciss.c:2534:1: note: an argument type that has a default promotion can’t match an empty parameter name list declaration
drivers/block/cciss.c:2515:18: note: previous implicit declaration of ‘fill_cmd’ was here
make[1]: *** [drivers/block/cciss.o] Error 1
make: *** [drivers/block/cciss.o] Error 2
Move fill_cmd() to above where it is first used.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is to allow number of commands reserved for use by SCSI tape drives
and medium changers to be adjusted at driver load time via the kernel
parameter cciss_tape_cmds, with a default value of 6, and a range
of 2 - 16 inclusive. Previously, the driver limited the number of
commands which could be queued to the SCSI half of the the driver
to only 2. This is to fix the problem that if you had more than
two tape drives, you couldn't, for example, erase or rewind them all
at the same time.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It causes NMIs which are undesirable at best, unsurvivable at worst.
Prefer the soft reset instead.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Just go straight to the soft-reset method instead.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
on driver load, if reset_devices is set, and the hard reset
attempts fail, try to bring up the controller to the point that
a command can be sent, and send it a soft reset command, then
after the reset undo whatever driver initialization was done to get
it to the point to take a command, and re-do it after the reset.
This is to get kdump to work on all the "non-resettable" controllers
(except 64xx controllers which can't be reset due to the potentially
shared cache module.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register. We want to
use it if it's available.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Just to reduce the messages about timeouts that appear.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When waiting for the board to become "not ready"
don't print a message saying "waiting for board to
become ready" (possibly followed by a message saying
"failed waiting for board to become not ready". Instead,
it should be "waiting for board to reset" and "failed
waiting for board to reset."
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
"
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Detect failure of controller reset by noticing if the 32 bytes of
"driver version" we store on the hardware in the config table
fail to get zeroed out. Previously we noticed if the controller
did not transition to "simple mode", but this did not detect reset
failure if the controller was already in simple mode prior to
the reset attempt (e.g. due to module parameter hpsa_simple_mode=1).
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
and fix a nearby typo, "do" that should have been "due"
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Controller will DMA only 32-bits of the tag per command
on completion if it knows we are only using 32-bit tags.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In process_nonindexed_cmd, hoist figuring of masked tag out of loop since
it is the same throughout.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This attribute, requested by Redhat, allows kexec-tools to know
whether the controller can honor the reset_devices kernel parameter
and actually reset the controller. For kdump to work properly it
is necessary that the reset_devices parameter be honored. This
attribute enables kexec-tools to warn the user if they attempt to
designate a non-resettable controller as the dump device.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit 8a3173de inadvertently changed the ordering when
switching to hlists. Change to regular list heads so we
can use tail list adds, this improves performance.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If you delete a logical drive, and then run BLKRRPART (e.g. via fdisk)
on a logical drive which is "after" the deleted logical drive in the h->drv[]
array, then cciss_revalidate panics because it will access the null pointer
h->drv[x] when x hits the deleted drive.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The recent patch to fix the removal of a non-existing proc
directory introduced this build problem for !CONFIG_PROC_FS:
drivers/block/cciss.c:4929: error: 'proc_cciss' undeclared (first use in this function)
Fix it by moving proc_cciss outside of the CONFIG_PROC_FS scope.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch removes the controller overlap between cciss and hpsa. It was
decided that no overlap should exist. All new controllers will use the hpsa
SCSI based driver.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Structure IOCTL_Command_struct is copied to userland with
some padding fields at the end of the struct unitialized.
It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We would prefer not to have any overlap between the two drivers.
Remove the cciss_allow_hpsa option, as it it is no longer needed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is to conserve memory in a memory-limited kdump scenario
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
After a reset, we should first wait for the board to become "not ready",
and then wait for it to become "ready", instead of immediately
waiting for it to become "ready", and do this waiting *after*
restoring PCI config space registers.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: fix PCI IDs for new controllers
This patch fixes the botched up PCI IDs of new controllers. Please consider
this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The block device drivers have all gained new lock_kernel
calls from a recent pushdown, and some of the drivers
were already using the BKL before.
This turns the BKL into a set of per-driver mutexes.
Still need to check whether this is safe to do.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The "h->scatter_list" is allocated inside a for loop. If any of those
allocations fail, then the rest of the list is uninitialized data. When
we free it we should start from the top and free backwards so that we
don't call kfree() on uninitialized pointers.
Also if the allocation for "h->scatter_list" fails then we would get an
Oops here. I should have noticed this when I send: 4ee69851c "cciss:
handle allocation failure." but I didn't. Sorry about that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Paolo Bonzini