Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.
This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.
The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove round robin configuration code for 82598 parts it
is not settable and is always false.
If we need/want this in the future we can add it back properly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.
The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.
This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.
By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds full support for SR-IOV by enabling the PF side.
VF side has already been committed.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...when invoked while interface is not up or when auto-negotiation is
disabled as done by other drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
*e1000_gstrings_test is not the same size as e1000_gstrings_test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The irony of the patch to fix the resume regression on PineView causing
a further regression on Ironlake is not lost on me.
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Reported-by: Björn Schließmann <chronoss@gmx.de>
Tested-by: Björn Schließmann <chronoss@gmx.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28802
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The documentation recommends that we should use a polling method for TV
detection as this is more power efficient than the interrupt based
mechanism (as the encoder can be completely switched off). A secondary
effect is that leaving the hotplug enabled seems to be causing pipe
underruns as reported by Hugh Dickins on his Crestline.
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[This is a candidate for stable, but needs minor porting to 2.6.37]
If the user changes the force-audio property and it no longer reflects
the current configuration, then we need to trigger a mode set in order
to update the registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Some keyboard controllers support more than 16 columns and rows.
Increase the limit to 32.
Signed-off-by: Trilok Soni <tsoni@codeaurora.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If we fail to retrieve HID descriptor we need to free allocated URB so
jump to proper label to do that.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When driver uses custom pendown detection method gpio_pendown is not
set up and so we should not try to free it, otherwise we are presented
with:
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:1258 gpio_free+0x100/0x12c()
Modules linked in:
[<c0061208>] (unwind_backtrace+0x0/0xe4) from [<c0091f58>](warn_slowpath_common+0x4c/0x64)
[<c0091f58>] (warn_slowpath_common+0x4c/0x64) from [<c0091f88>](warn_slowpath_null+0x18/0x1c)
[<c0091f88>] (warn_slowpath_null+0x18/0x1c) from [<c024e610>](gpio_free+0x100/0x12c)
[<c024e610>] (gpio_free+0x100/0x12c) from [<c03e9fbc>](ads7846_probe+0xa38/0xc5c)
[<c03e9fbc>] (ads7846_probe+0xa38/0xc5c) from [<c02cff14>](spi_drv_probe+0x18/0x1c)
[<c02cff14>] (spi_drv_probe+0x18/0x1c) from [<c028bca4>](driver_probe_device+0xc8/0x184)
[<c028bca4>] (driver_probe_device+0xc8/0x184) from [<c028bdc8>](__driver_attach+0x68/0x8c)
[<c028bdc8>] (__driver_attach+0x68/0x8c) from [<c028b4c8>](bus_for_each_dev+0x48/0x74)
[<c028b4c8>] (bus_for_each_dev+0x48/0x74) from [<c028ae08>](bus_add_driver+0xa0/0x220)
[<c028ae08>] (bus_add_driver+0xa0/0x220) from [<c028c0c0>](driver_register+0xa8/0x134)
[<c028c0c0>] (driver_register+0xa8/0x134) from [<c0050550>](do_one_initcall+0xcc/0x1a4)
[<c0050550>] (do_one_initcall+0xcc/0x1a4) from [<c00084e4>](kernel_init+0x14c/0x214)
[<c00084e4>] (kernel_init+0x14c/0x214) from [<c005b494>](kernel_thread_exit+0x0/0x8)
---[ end trace 4053287f8a5ec18f ]---
Also rearrange ads7846_setup_pendown() to have only one exit point
returning success.
Reported-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Charulatha V <charu@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This netbook has a only one jack output and an internal mic.
By default, mic and jack sense aren't working. Using lenovo-101e
parameters makes both work.
The device seems based on a Sharetronic Q70, so this should fix audio for
this model too.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 80c802f307 (xfrm: cache bundles instead of policies for
outgoing flows) introduced possible oopse when dst_alloc returns NULL.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris noted that commit de139a3 ("pci: check caps from sysfs file
open to read device dependent config space") caused the capability check
to bypass security modules and potentially auditing. Rectify this by
calling security_capable() when checking the open file's capabilities
for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
Expand security_capable() to include cred, so that it can be usable in a
wider range of call sites.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
Follow kernel coding style traditions more closely.
Delete typedef, re-name "per cpu counters" to
simply be counters etc.
This patch changes no functionality.
Suggested-by: Thiago Farina <tfransosi@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
bug could cause false positive on indicating
presence of invarient TSC or APERF support.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
As a precautionary measure, expand the fix submitted in commit
4d163b75e9 entitled "tg3: Fix 5719 A0 tx
completion bug" to apply to all 5719 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-I (include path) should be specified for host builds.
This one was overlooked somehow. Fixes
https://bugzilla.kernel.org/show_bug.cgi?id=25902
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Alexey Salmin <alexey.salmin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slight revision to this patch...use min_t() instead of conditional
assignment. Also, remove the FIXME comment and replace it with the
explanation that Steve gave earlier.
After receiving a packet, we currently check the header. If it's no
good, then we toss it out and continue the loop, leaving the caller
waiting on that response.
In cases where the packet has length inconsistencies, but the MID is
valid, this leads to unneeded delays. That's especially problematic now
that the client waits indefinitely for responses.
Instead, don't immediately discard the packet if checkSMB fails. Try to
find a matching mid_q_entry, mark it as having a malformed response and
issue the callback.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The current TPM TIS driver in git discards the timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
I am also adding a sysfs entry 'timeouts' showing the timeouts that are
being used.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes an OOPS triggered when calling modprobe ipmi_si a
second time after the first modprobe returned without finding any ipmi
devices. This can happen if you reload the module after having the
first module load fail. The driver was not deregistering from PNP in
that case.
Peter Huewe originally reported this patch and supplied a fix, I have a
different patch based on Linus' suggestion that cleans things up a bit
more.
Cc: stable@kernel.org
Cc: openipmi-developer@lists.sourceforge.net
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit ce6ada35bd ("security: Define CAP_SYSLOG") Serge Hallyn
introduced CAP_SYSLOG, but broke backwards compatibility by no longer
accepting CAP_SYS_ADMIN as an override (it would cause a warning and
then reject the operation).
Re-instate CAP_SYS_ADMIN - but keeping the warning - as an acceptable
capability until any legacy applications have been updated. There are
apparently applications out there that drop all capabilities except for
CAP_SYS_ADMIN in order to access the syslog.
(This is a re-implementation of a patch by Serge, cleaning the logic up
and making the code more readable)
Acked-by: Serge Hallyn <serge@hallyn.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously we were relying on it being pulled in by other headers for
the prototype of s3c24xx_irq_suspend() and s3c24xx_irq_resume().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch cleans following up.
- Moved definition of System MMU IPNUM into mach/sysmmu.h
- Removed useless SYSMMU_DEBUG configuration
- Removed useless header file plat/sysmmu.h
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The 's5pv310_device_sysmmu' is used on SMDKV310. But since it is not
compiled now, there is a build error. To fix this compilation error,
S5PV310_DEV_SYSMMU needs to be selected for SMDKV310 board.
This patch enables System MMU support on SMDKV310.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: Adding description]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The two fragments of an unicast packet must have successive sequence numbers to
allow the receiver side to detect matching fragments and merge them again. The
current implementation doesn't provide that property because a sequence of two
atomic_inc_return may be interleaved with another sequence which also changes
the variable.
The access to the fragment sequence number pool has either to be protected by
correct locking or it has to reserve two sequence numbers in a single fetch.
The latter one can easily be done by increasing the value of the last used
sequence number by 2 in a single step. The generated window of two currently
unused sequence numbers can now be scattered across the two fragments.
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
If we didn't have a routing cache, we would not be able to properly
propagate certain kinds of dynamic path attributes, for example
PMTU information and redirects.
The reason is that if we didn't have a routing cache, then there would
be no way to lookup all of the active cached routes hanging off of
sockets, tunnels, IPSEC bundles, etc.
Consider the case where we created a cached route, but no inetpeer
entry existed and also we were not asked to pre-COW the route metrics
and therefore did not force the creation a new inetpeer entry.
If we later get a PMTU message, or a redirect, and store this
information in a new inetpeer entry, there is no way to teach that
cached route about the newly existing inetpeer entry.
The facilities implemented here handle this problem.
First we create a generation ID. When we create a cached route of any
kind, we remember the generation ID at the time of attachment. Any
time we force-create an inetpeer entry in response to new path
information, we bump that generation ID.
The dst_ops->check() callback is where the knowledge of this event
is propagated. If the global generation ID does not equal the one
stored in the cached route, and the cached route has not attached
to an inetpeer yet, we look it up and attach if one is found. Now
that we've updated the cached route's information, we update the
route's generation ID too.
This clears the way for implementing PMTU and redirects directly in
the inetpeer cache. There is absolutely no need to consult cached
route information in order to maintain this information.
At this point nothing bumps the inetpeer genids, that comes in the
later changes which handle PMTUs and redirects using inetpeers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Validity of the cached PMTU information is indicated by it's
expiration value being non-zero, just as per dst->expires.
The scheme we will use is that we will remember the pre-ICMP value
held in the metrics or route entry, and then at expiration time
we will restore that value.
In this way PMTU expiration does not kill off the cached route as is
done currently.
Redirect information is permanent, or at least until another redirect
is received.
Signed-off-by: David S. Miller <davem@davemloft.net>
Future changes will add caching information, and some of
these new elements will be addresses.
Since the family is implicit via the ->daddr.family member,
replicating the family in ever address we store is entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
USB: cdc-acm: Adding second ACM channel support for Nokia N8
USB, Mass Storage, composite, gadget: Fix build failure and memset of a struct
USB: Fix trout build failure with ci13xxx_msm gadget
USB: EHCI: fix scheduling while atomic during suspend
USB: usb-storage: unusual_devs entry for Coby MP3 player
USB: ftdi_sio: Add VID=0x0647, PID=0x0100 for Acton Research spectrograph
USB: fix race between root-hub resume and wakeup requests
USB: prevent buggy hubs from crashing the USB stack
usb: r8a66597-udc: Fixed bufnum of Bulk
USB: ftdi_sio: add ST Micro Connect Lite uart support
USB: Storage: Add unusual_devs entry for VTech Kidizoom
USB SL811HS HCD: Fix memory leak in sl811h_urb_enqueue()
USB: ti_usb: fix module removal
USB: io_edgeport: fix the reported firmware major and minor
usb: ehci-omap: Show fatal probing time errors to end user
usb: musb: introduce api for dma code to check compatibility with usb request
usb: musb: maintain three states for buffer mappings instead of two
usb: musb: disable double buffering when it's broken
usb: musb: hsdma: change back to use musb_read/writew
usb: musb: core: fix IRQ check
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bfin_5xx: split uart RX lock from uart port lock to avoid deadlock
68360serial: Plumb in rs_360_get_icount()
n_gsm: copy mtu over when configuring via ioctl interface
virtio: console: Move file back to drivers/char/
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: zram: fix data corruption issue
Staging: Comedi: Fix a few NI module dependencies
Staging: comedi: Add MODULE_LICENSE and similar to NI modules
staging: brcm80211: bugfix for softmac crash on multi cpu configurations
staging: sst: Fix for dmic capture on v2 pmic
staging: hv: Enable sending GARP packet after live migration
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
virtio_net: Add schedule check to napi_enable call
x25: Do not reference freed memory.
pch_can: fix tseg1/tseg2 setting issue
isdn: hysdn: Kill (partially buggy) CVS regision log reporting.
can: softing_cs needs slab.h
pch_gbe: Fix the issue which a driver locks when rx offload is set by ethtool
netfilter: nf_conntrack: set conntrack templates again if we return NF_REPEAT
pch_can: fix module reload issue with MSI
pch_can: fix rmmod issue
pch_can: fix 800k comms issue
net: Fix lockdep regression caused by initializing netdev queues too early.
net/caif: Fix dangling list pointer in freed object on error.
USB CDC NCM errata updates for cdc_ncm host driver
CDC NCM errata updates for cdc.h
ixgbe: update version string
ixgbe: cleanup variable initialization
ixgbe: limit VF access to network traffic
ixgbe: fix for 82599 erratum on Header Splitting
ixgbe: fix variable set but not used warnings by gcc 4.6
e1000: add support for Marvell Alaska M88E1118R PHY
...
The following panic BUG_ON occurs during qib testing:
Kernel BUG at include/linux/timer.h:82
RIP [<ffffffff881f7109>] :ib_qib:start_timer+0x73/0x89
RSP <ffffffff80425bd0>
<0>Kernel panic - not syncing: Fatal exception
<0>Dumping qib trace buffer from panic
qib_set_lid INFO: IB0:1 got a lid: 0xf8
Done dumping qib trace buffer
BUG: warning at kernel/panic.c:137/panic() (Tainted: G
The flaw is due to a missing state test when processing responses that
results in an add_timer() call when the same timer is already queued.
This code was executing in parallel with a QP destroy on another CPU
that had changed the state to reset, but the missing test caused to
response handling code to run on into the panic.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Under harsh testing conditions, including low memory, the guest would
stop receiving packets. With this patch applied we no longer see any
problems in the driver while performing these tests for extended periods
of time.
Make sure napi is scheduled subsequent to each napi_enable.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Olaf Kirch <okir@suse.de>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a hang when booting as dom0 under Xen, when jiffies can be
quite large by the time the kernel init gets this far.
Signed-off-by: Tim Deegan <Tim.Deegan@citrix.com>
[jbeulich@novell.com: !time_after() -> time_before_eq() as suggested by Jiri Slaby]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bb758e9637 removed snd_hrtimer_callback() from the hardware
interrupt handler, thus moving it into a tasklet, but did not tell the
ALSA timer framework about this, so the timer handling would now be done
in the ALSA timer tasklet scheduled from another tasklet.
To fix this, add the flag to tell the ALSA timer framework that the
timer handler is already being invoked in a tasklet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a timer interrupt was delayed too much, hrtimer_forward_now() will
forward the timer expiry more than once. When this happens, the
additional number of elapsed ALSA timer ticks must be passed to
snd_timer_interrupt() to prevent the ALSA timer from falling behind.
This mostly fixes MIDI slowdown problems on highly-loaded systems with
badly behaved interrupt handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the reporter, node 0x15 needs to be muted for subwoofer
to stop sounding. This pin is marked as unused by BIOS, so fix that.
BugLink: http://bugs.launchpad.net/bugs/715877
Cc: stable@kernel.org (2.6.37+)
Reported-by: Hans Peter
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an empty string is passed to patch option, the driver should
ignore it. Otherwise it gets an error by trying to load it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since tail is the previous fp - 1, we need to compare the new fp with tail + 1
to ensure that we don't end up passing in the same tail again, in order to
avoid a potential infinite loop in the perf interrupt handler (which has been
observed to occur). A similar fix seems to be needed in the OProfile code.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With certain configurations, we inline the unlock functions in modules,
which results in SMP alternatives being created in modules. We need to
fix those up when loading a module to prevent undefined instruction
faults.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jeff Moyer reported these messages:
Warning: ... trying to fall back to cpu-clock-ticks
couldn't open /proc/-1/status
couldn't open /proc/-1/maps
[ls output]
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.008 MB perf.data (~363 samples) ]
That lead me and David Ahern to see that something was fishy on the thread
synthesizing routines, at least for the case where the workload is started
from 'perf record', as -1 is the default for target_tid in 'perf record --tid'
parameter, so somehow we were trying to synthesize the PERF_RECORD_MMAP and
PERF_RECORD_COMM events for the thread -1, a bug.
So I investigated this and noticed that when we introduced support for
recording a process and its threads using --pid some bugs were introduced and
that the way to fix it was to instead of passing the target_tid to the event
synthesizing routines we should better pass the thread_map that has the list of
threads for a --pid or just the single thread for a --tid.
Checked in the following ways:
On a 8-way machine run cyclictest:
[root@emilia ~]# perf record cyclictest -a -t -n -p99 -i100 -d50
policy: fifo: loadavg: 0.00 0.13 0.31 2/139 28798
T: 0 (28791) P:99 I:100 C: 25072 Min: 4 Act: 5 Avg: 6 Max: 122
T: 1 (28792) P:98 I:150 C: 16715 Min: 4 Act: 6 Avg: 5 Max: 27
T: 2 (28793) P:97 I:200 C: 12534 Min: 4 Act: 5 Avg: 4 Max: 8
T: 3 (28794) P:96 I:250 C: 10028 Min: 4 Act: 5 Avg: 5 Max: 96
T: 4 (28795) P:95 I:300 C: 8357 Min: 5 Act: 6 Avg: 5 Max: 12
T: 5 (28796) P:94 I:350 C: 7163 Min: 5 Act: 6 Avg: 5 Max: 12
T: 6 (28797) P:93 I:400 C: 6267 Min: 4 Act: 5 Avg: 5 Max: 9
T: 7 (28798) P:92 I:450 C: 5571 Min: 4 Act: 5 Avg: 5 Max: 9
^C[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.108 MB perf.data (~4719 samples) ]
[root@emilia ~]#
This will create one extra thread per CPU:
[root@emilia ~]# tuna -t cyclictest -CP
thread ctxt_switches
pid SCHED_ rtpri affinity voluntary nonvoluntary cmd
28825 OTHER 0 0xff 2169 671 cyclictest
28832 FIFO 93 6 52338 1 cyclictest
28833 FIFO 92 7 46524 1 cyclictest
28826 FIFO 99 0 209360 1 cyclictest
28827 FIFO 98 1 139577 1 cyclictest
28828 FIFO 97 2 104686 0 cyclictest
28829 FIFO 96 3 83751 1 cyclictest
28830 FIFO 95 4 69794 1 cyclictest
28831 FIFO 94 5 59825 1 cyclictest
[root@emilia ~]#
So we should expect only samples for the above 9 threads when using the
--dump-raw-trace|-D perf report switch to look at the column with the tid:
[root@emilia ~]# perf report -D | grep RECORD_SAMPLE | cut -d/ -f2 | cut -d: -f1 | sort | uniq -c
629 28825
110 28826
491 28827
308 28828
198 28829
621 28830
225 28831
203 28832
89 28833
[root@emilia ~]#
So for workloads started by 'perf record' seems to work, now for existing workloads,
just run cyclictest first, without 'perf record':
[root@emilia ~]# tuna -t cyclictest -CP
thread ctxt_switches
pid SCHED_ rtpri affinity voluntary nonvoluntary cmd
28859 OTHER 0 0xff 594 200 cyclictest
28864 FIFO 95 4 16587 1 cyclictest
28865 FIFO 94 5 14219 1 cyclictest
28866 FIFO 93 6 12443 0 cyclictest
28867 FIFO 92 7 11062 1 cyclictest
28860 FIFO 99 0 49779 1 cyclictest
28861 FIFO 98 1 33190 1 cyclictest
28862 FIFO 97 2 24895 1 cyclictest
28863 FIFO 96 3 19918 1 cyclictest
[root@emilia ~]#
and then later did:
[root@emilia ~]# perf record --pid 28859 sleep 3
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.027 MB perf.data (~1195 samples) ]
[root@emilia ~]#
To collect 3 seconds worth of samples for pid 28859 and its children:
[root@emilia ~]# perf report -D | grep RECORD_SAMPLE | cut -d/ -f2 | cut -d: -f1 | sort | uniq -c
15 28859
33 28860
19 28861
13 28862
13 28863
10 28864
11 28865
9 28866
255 28867
[root@emilia ~]#
Works, last thing is to check if looking at just one of those threads also works:
[root@emilia ~]# perf record --tid 28866 sleep 3
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.006 MB perf.data (~242 samples) ]
[root@emilia ~]# perf report -D | grep RECORD_SAMPLE | cut -d/ -f2 | cut -d: -f1 | sort | uniq -c
3 28866
[root@emilia ~]#
Works too.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
amd64_debug_display_dimm_sizes() reports the distribution of the DIMMs
on each DRAM controller and its chip select sizes. Thus, the last don't
have anything to do with whether we're running in ganged DCT mode or not
- their sizes don't change all of a sudden. Fix that by removing the
ganged-check and dump DCT0's config for DCT1 when in ganged mode since
they're identical.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
SWP emulation requires that CPU domain support is disabled in order to
work safely. Make that explicit in the kernel configuration to prevent
illegal configurations being generated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
John Fastabend