this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This counter is valuable to determine if the system is unable
to timely return buffers to the hardware and this counter starts
to increase well before the hardware starts to drop packets. If
users experience rx_no_buffer_count increasing, they should increase
the amount of descriptors. That will provide more buffers for the
hardware and will decrease the chance of hard drops.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix NCFGR.SPD setting on 10Mbps. This bug was introduced by
conversion to generic PHY layer in kernel 2.6.23.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use register offset definition for WOLcgClr, rather than a magic
number.
This patch does not change the driver behaviour.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch eliminates a kernel panic with the igb driver in 2.6.25-rc2 when
running on a Intel 82575 Ethernet controller with a 1000BASE-SX PHY. The
panic does not happen with the 1000BASE-T PHY, only with a SX connection.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change all dma op invocations in gianfar.c to actually pass in the
device pointer. Currently, the value is ignored, but it will be
used going forward as we implement archdata for 32-bit powerpc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading a serie of zero from the cmos sram area do not work
well with is_valid_ether_addr(). Let's read the mac address
from the eeprom first as it seems more reliable.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9831
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The forward declarations were already marked static, make the definitions
be static as well. Fixes the sparse warnings as well.
drivers/net/tlan.c:1403:5: warning: symbol 'TLan_HandleInvalid' was not declared. Should it be static?
drivers/net/tlan.c:1435:5: warning: symbol 'TLan_HandleTxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1521:5: warning: symbol 'TLan_HandleStatOverflow' was not declared. Should it be static?
drivers/net/tlan.c:1557:5: warning: symbol 'TLan_HandleRxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1692:5: warning: symbol 'TLan_HandleDummy' was not declared. Should it be static?
drivers/net/tlan.c:1722:5: warning: symbol 'TLan_HandleTxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1770:5: warning: symbol 'TLan_HandleStatusCheck' was not declared. Should it be static?
drivers/net/tlan.c:1845:5: warning: symbol 'TLan_HandleRxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1905:6: warning: symbol 'TLan_Timer' was not declared. Should it be static?
drivers/net/tlan.c:1986:6: warning: symbol 'TLan_ResetLists' was not declared. Should it be static?
drivers/net/tlan.c:2046:6: warning: symbol 'TLan_FreeLists' was not declared. Should it be static?
drivers/net/tlan.c:2095:6: warning: symbol 'TLan_PrintDio' was not declared. Should it be static?
drivers/net/tlan.c:2130:6: warning: symbol 'TLan_PrintList' was not declared. Should it be static?
drivers/net/tlan.c:2166:6: warning: symbol 'TLan_ReadAndClearStats' was not declared. Should it be static?
drivers/net/tlan.c:2242:1: warning: symbol 'TLan_ResetAdapter' was not declared. Should it be static?
drivers/net/tlan.c:2328:1: warning: symbol 'TLan_FinishReset' was not declared. Should it be static?
drivers/net/tlan.c:2451:6: warning: symbol 'TLan_SetMac' was not declared. Should it be static?
drivers/net/tlan.c:2493:6: warning: symbol 'TLan_PhyPrint' was not declared. Should it be static?
drivers/net/tlan.c:2542:6: warning: symbol 'TLan_PhyDetect' was not declared. Should it be static?
drivers/net/tlan.c:2589:6: warning: symbol 'TLan_PhyPowerDown' was not declared. Should it be static?
drivers/net/tlan.c:2614:6: warning: symbol 'TLan_PhyPowerUp' was not declared. Should it be static?
drivers/net/tlan.c:2635:6: warning: symbol 'TLan_PhyReset' was not declared. Should it be static?
drivers/net/tlan.c:2663:6: warning: symbol 'TLan_PhyStartLink' was not declared. Should it be static?
drivers/net/tlan.c:2750:6: warning: symbol 'TLan_PhyFinishAutoNeg' was not declared. Should it be static?
drivers/net/tlan.c:2906:5: warning: symbol 'TLan_MiiReadReg' was not declared. Should it be static?
drivers/net/tlan.c:2996:6: warning: symbol 'TLan_MiiSendData' was not declared. Should it be static?
drivers/net/tlan.c:3038:6: warning: symbol 'TLan_MiiSync' was not declared. Should it be static?
drivers/net/tlan.c:3077:6: warning: symbol 'TLan_MiiWriteReg' was not declared. Should it be static?
drivers/net/tlan.c:3147:6: warning: symbol 'TLan_EeSendStart' was not declared. Should it be static?
drivers/net/tlan.c:3187:5: warning: symbol 'TLan_EeSendByte' was not declared. Should it be static?
drivers/net/tlan.c:3248:6: warning: symbol 'TLan_EeReceiveByte' was not declared. Should it be static?
drivers/net/tlan.c:3306:5: warning: symbol 'TLan_EeReadByte' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* If ConfigBase is 0x03c0 && manfid is (0x0149,0xc1ab),
printk "use axnet_cs instead" message.
Actually, most of the card with manfid(0x0149, 0xc1ab)
use pcnet_cs driver.
* remove entry (0x021b, 0x0202)
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Suppress the warning message about the 'netcard_portlist' defined but not used.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=5839
Init sequence needs to poll phy until phy reset is complete. This is the
same problem that I fixed in 2002 in tulip driver.
Thanks to manty@manty.net for testing this patch.
Thanks to Pozsar Balazs <pozsy@uhulinux.hu> for posting/testing
a similar patch before:
http://lkml.org/lkml/2006/8/21/45
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I booted an igb kernel with the option pci=nomsi and instantly noticed
that interrupts no longer worked on my igb device. I took a look at the
interrupt initialization and quickly discovered a comment stating:
"DO NOT USE EIAME or IAME in legacy mode"
It seemed a bit odd that bits to enable IAM were being set in legacy
interrupt mode, so I dropped out the following parts and interrupts
began working fine again.
[Updated code flow and a nitpick spelling error --Auke]
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The lock acquisition in fs_ioctl() does not appear to actually be necessary,
and thus is simply removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds kdump support to the ehea driver. As the firmware doesn't free
resource handles automatically, the driver has to run an as simple as possible
free resource function in case of a crash shutdown. The function iterates over
two arrays freeing all resource handles which are stored there. The arrays are
kept up-to-date during normal runtime. The crash handler fn is triggered by the
recently introduced PPC crash shutdown reg/unreg functions.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When asked to blink LEDs the tg3 driver behaves when using:
ethtool -p ethX
The default value for data is zero, and other drivers interpret this
as blink forever (or at least a really long time). The tg3 driver
interprets this as blink once. All drivers should have the same
behaviour.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches to workaround the 5706S on an HP blade were not
sufficient. The link state still does not change properly in some
cases. This patch adds polling to make it completely reliable.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This silences sparse when run on zd1211rw.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This silences a few sparse warnings. There are two more where
I can't follow the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'u64' is not necessarily 'unsigned long long'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_beacon_update_timers':
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_intr':
drivers/net/wireless/ath5k/base.c:2391: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse sees int -> bool cast as an error:
hw.c:3754:10: warning: cast truncates bits from constant value (ffffffea becomes 0)
Fix it by converting the rettype to int and check appropriately.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Omitted lock causes sparse warning
drivers/net/wireless/ath5k/base.c:1682:1: warning: context imbalance in 'ath5k_tasklet_rx' - different lock contexts for basic block
Add the lock to the guilty fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on report from Cavan Carroll <cavancarroll@hotmail.com>:
http://bugzilla.kernel.org/show_bug.cgi?id=9863
Cc: Cavan Carroll <cavancarroll@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When deleting the veth driver, veth_close calls netif_carrier_off
for the two extremities of the network device. netif_carrier_off on
the peer device will fire an event and hold a reference on the peer
device. Just after, the peer is unregistered taking the rtnl_lock while
the linkwatch_event is scheduled. If __linkwatch_run_queue does not
occurs before the unregistering, unregister_netdevice will wait for
the dev refcount to reach zero holding the rtnl_lock and linkwatch_event
will wait for the rtnl_lock and hold the dev refcount.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matheos Worku <Matheos.Worku@Sun.COM>
1) niu_enable_alt_mac() needs to be adjusted so that the mask
is computed properly for the BMAC case.
2) BMAC has 6 alt MAC addresses available, not 7.
Signed-off-by: David S. Miller <davem@davemloft.net>
BMAC port alternate MAC address index needs to start at 1. Index 0 is
used for the main MAC address.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the removal the the "rgmii-interface" device_type property from the
dts files, the newemac driver needs an update to only rely on compatible
property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds printk messages with basic information about the driver being loaded.
This information includes a summary of the compiled-in features, which
simplifies bug-reporting and debugging a lot.
Also a firmware ID is printed. This is a unique identifier blob for a specific
version of the firmware. This ID is attached to a specific version of the firmware
blob in b43-fwcutter (see fwcutter git).
This helps users to select the right firmware for their device.
This also makes it possible to use automated scripts to fetch and extract the right
firmware for the driver. (The script will grep the .ko for the "Firmware-ID: xxx" string.)
While the driver might still support other versions of the firmware for backward
compatibility, this will always print out the officially supported version, which
people _should_ use.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restock the RX queue when there are a lot of unused frames so that the
RX ring buffer doesn't overrun, causing a ucode assertion. Backport of
patch "iwlwifi: fix ucode assertion for RX queue overrun".
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no association process in IBSS mode - so testing the
association id is not needed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
CC: Richard Scherping <richard@scherping.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revert commit blow that wrongly suppressed sparse warning in
iwlwifi eeprom reading
In addtion it suppresses correctly the iwlwifi eeprom register reading anomaly.
commit 45883ae47a0a4700c0f4716dc75a255cccdc3a76
misc wireless annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware version information should always get printed. Not only on a
debug build.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the firmware ID to modinfo.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware version information should always get printed. Not only
on a debug build.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds printk messages with basic information about the driver being loaded.
This information includes a summary of the compiled-in features, which
simplifies bug-reporting and debugging a lot.
Also a firmware ID is printed. This is a unique identifier blob for a specific
version of the firmware. This ID is attached to a specific version of the firmware
blob in b43-fwcutter (see fwcutter git).
This helps users to select the right firmware for their device.
This also makes it possible to use automated scripts to fetch and extract the right
firmware for the driver. (the script will grep the .ko for the "Firmware-ID: xxx" string.
While the driver might still support other versions of the firmware for backward
compatibility, this will always print out the officially supported version, which
people _should_ use.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This checks if the DMA address is bigger than what the controller can manage.
It will reallocate the buffers in the GFP_DMA zone in that case.
The patch by Michael Buesch has been ported to b43legacy.
Thanks to Matti Viljanen for reporting this.
Cc: Matti Viljanen <viljanen.matti@gmail.com>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Value of count is used to decide when to replenish rx buffers. If it is
equal or above 8 we replenish the buffers. Ensure there is no starvation
by initializing count to 8 - thus forcing replenish at first iteration.
This is helpful when rx receives batches of buffers smaller than 8.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prevents sending host commands when rfkill is on
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The geos information is set up during probe and should only
be removed during pci_remove, not during _down.
This is a temporary fix until the setting of the status bits
have been cleaned up (to explicitly match all setting with
clearing of status bits).
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jesse Brandeburg