1. the following code to configure PGSRx is no way portable and
intuitive:
- PGSR0 = 0x00008800;
- PGSR1 = 0x00000002;
- PGSR2 = 0x0001FC00;
- PGSR3 = 0x00001F81;
this is removed as low power state has already been encoded in
the pin configuration definitions.
Note: there is no specific reason for some of the GPIOs to drive
high in low power mode as indicated by the above setting, those
bits are ignored, and the result is validated to work.
2. the following code to configure GPIO wakeup is removed as this
is now totally handled by pxa2xx_mfp_config():
- PWER = 0xC0000002;
- PRER = 0x00000002;
- PFER = 0x00000002;
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MFP configurations after resume should be done before the GPIO registers
are restored. Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The main issue here is that pxa3xx does not have GAFRx registers,
access directly to these registers should be avoided for pxa3xx:
1. introduce __gpio_is_occupied() to indicate the GAFRx and GPDRx
registers are already configured on pxa{25x,27x} while returns
0 always on pxa3xx
2. pxa_gpio_mode(gpio | GPIO_IN) is replaced directly with assign-
ment of GPDRx, the side effect of this change is that the pin
_must_ be configured before use, pxa_gpio_irq_type() will not
change the pin to GPIO, as this restriction is sane, esp. with
the new MFP framework
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To further clean up the GPIO and IRQ structure:
1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
function pxa_init_gpio()
2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
an argument
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by
1. wrapping long lines and making comments tidy
2. using IRQ_TYPE_* instead of migration macros __IRQT_*
3. introduce a pr_debug() for the commented printk(KERN_DEBUG ...)
stuff
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by:
1. introduce dedicated pxa_{mask,unmask}_low_gpio()
2. remove set_irq_chip(IRQ_GPIO_2_x, ...) which has already been
initialized in pxa_init_irq()
3. introduce dedicated pxa_init_gpio_set_wake()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. As David Brownell suggests, using ffs() is going to make the loop
a bit faster (by avoiding unnecessary shift and iteration)
2. Russell suggested find_{first,next}_bit() being used with the
gedr[] array
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AC97 clock rate on PXA3xx is generated with a configurable divider
from sys_pll.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we fail to boot due to an unsupported processor ID, print the
processor ID as part of the failure message.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
U-Boot puts an image at the load address specified in the uImage
header before jumping to the entry point.
In the CONFIG_ZBOOT_ROM case ZBOOT_ROM_TEXT is the right load
address.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
By default, this option was selected by the platform Kconfig. This
patch adds "depends on" to L2X0 so that it can be enabled/disabled
manually.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch enables the building of Linux for the PB1176 platform.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the base files for the PB1176 platform support.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the resource and device definitions for the compact
flash.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the PB11MPCore support to the corresponding Kconfig
and Makefile to enable building.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the base files for the PB11MPCore platform support.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The upcoming PB11MPCore and PB1176 have different memory maps and some
of the definitions in platform.h are no longer common. This patch
moves them to the board-eb.h file and updates their usage in
realview_eb.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since the PB1176 has different UART base addresses, this patch moves
the definitions form platorm.h to board-eb.h. It also modifies
uncompress.h to detect the platform type at run-time.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the timer definitions from platform.h into board-eb.h
as they are different on PB11MPCore and PB1176. It also adds
timerX_va_base variables in core.c which are set by the
realview_eb_timer_init function before invoking realview_timer_init.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the patch definitions into board-eb.h and
realview_eb.c (from core.c) as they are different on the PB11MPCore
and PB1176 platforms.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This is in preparation for the RealView PB11MPCore and PB1176 patches
which have different base addresses for the GIC.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
RealView/EB revD platform comes with the SMSC LAN9118 Ethernet
chip. This patch allows either the smc91x or the smc911x drivers to be
used with the RealView/EB platform.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the SCU initialisation from __v6_setup to the
smp_prepare_cpus() function as it relies on platform-specific
settings. Changes to get_core_count() are mainly for allowing cleaner
code with the upcoming PB11MPCore patches.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch implements Thumb-2 application support in Linux. Original
implementation by Paul Brook with fixes for VFP and Neon by Catalin
Marinas.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a prefetch abort handler similar to the data abort one
and renames the latter for consistency. Initial implementation by Paul
Brook with some renaming by Catalin Marinas.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add the TinCanTools Hammer board to list of supported machines in the
arch/arm/mach-s3c2410 directory, as well as a default config entry. the
mach-tct_hammer.c file initializes basic i/o, clocks, irqs, as well as
the mtd flash layout if enabled in the kernel configuration.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There seems to be some problem with at-least the S3C2440 and
bus traffic during an reset. It is unlikely, but still possible
that the system will hang in such a way that the watchdog cannot
get the system out of the state it is in.
Change to making the code that calls the watchdog reset run from
cached memory so that instruction fetches have quiesced before the
watchdog fires.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All current Simtec designs source the DCLK outputs from
the UPLL. This means the DCLK's parent must be set to UPLL
so that anything enabling and disabling an UPLL sourced
clock does not shutdown the DCLK due to missing open counts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the name of the S3C2412_CLKDIVN_ARMDIVN define.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change GPA21 to output over reset so that nRSTOUT is not
asserted whilst suspended.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Juergen Beisert <j.beisert@pengutronix.de>
This patch separates the current code into i.MX2 and i.MX3 and modifies
the Kconfig files to reflect this separation in the menus.
Things happend since last review:
- make i.MX3 compile again
- fix some structure names to be conform with all the shared/common
sources from i.MX1/i.MX2
Previous changes:
- stay conform to other Kconfig files (note from Russell King)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eric miao